Phoenix PWB-1535A Manuel utilisateur
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
1 / 24
Installation and Operation Manual
Wheel Balancer
PWB – 1535A
ATTENTION - Please read the instruction before using this product. Failure
to follow the instructions may result in serious injury. Keep the instruction
for reference by operators.
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
2 / 24
Table of Contents
1. Safety Instructions …………..................................................3
a. Owner’s Responsibility
b. Intended Use
c. Precaution
2. Product Specification ..............................................................5
3. Product Installation …………..................................................6
4. Control Panel ...........................................................................6
5. System Setting ..........................................................................8
6. Wheel Parameters Input .......................................................11
6.1 Input 3 Parameters of Wheel with Automatic Gauge ...........12
6.2 Input 4 Parameters of Wheel with Automatic Gauge ...........13
6.3 Input Parameters Manually ..............................................14
7. Calibration .............................................................................14
8. Standard Dynamic Mode ......................................................17
9. Static Mode .............................................................................20
10. ALU1-3 modes ......................................................................20
11. ALUS Mode ..........................................................................21
12. OPT Mode .............................................................................21
13. Motorcycle Mode .................................................................22
14. Errors and Trouble Shooting ..............................................22
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
3 / 24
1. Safety Instructions
a. Owner’s Responsibility
In order to maintain your product properly and to ensure operator
safety, it is the responsibility of the owner to read and follow these
instructions:
All operators should be properly trained.
All operators should not wear loose clothing or jewelry. These
things may become entangled with the wheel or turntable
while using the changer and could cause serious injury.
All operators should wear protective eye gear. Safety glasses
with side shields, goggles, or face shields are acceptable
All operators recommend wear sturdy leather work shoes with
steel toes and oil resistant soles, to prevent injury in typical
shop activities.
Safety guard should be used to avoid injury.
The wheel balancer contains electronics and should be kept
indoors and in a dry environment. Exposure to water can cause
damage and is not covered under any warranty.
Exposure to extreme heat can damage internal parts of the
wheel balancer.
The wheel balancer does not have an electrical surge protector.
The user should supply a surge protector to avoid damage to
the wheel balancer in the event of an electrical surge or storm.
Do not use the wheel balancer beyond its measurement or
weight range. Using the wheel balancer beyond its
measurement or weight range could cause damage to the
wheel balancer and does not ensure a precise balance of the
wheel.
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
4 / 24
Other safety regulations may be in place according to OSHA or
your local city and county. These should all be followed in
addition to the instructions in this manual.
Keep all instructions permanently with the unit and all labels
and notices are clean and visible
b. Intended Use
The balance will automatically enter the distance of the wheel
from machine and the diameter of the rim. You only have to
enter the width. Standard balancers require you to enter all
three parameters manually, but this 1535A model makes the
process quick and easy.
The wheel Balancer has been designed and manufactured
exclusively for balance tires.
Manufacturer cannot be held responsible for any damage
caused through the use of the Wheel Balancer for purposes
other than the specified in this manual.
c. Precaution
Any tampering or modification to the equipment carried out
without the manufacturer’s prior authorization will free
Manufacturer from all responsibility for damage caused
directly or indirectly by the above actions.
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
5 / 24
2. Product Specification
Rim Diameter 10"-28"
Rim Width 1.5"-20"
Maximum wheel weight 155 lbs.
Cycle Time 8 seconds
Power supply 110v/1ph
+ or - 1 gram of accuracy
Oz/Gram switch
Standard Dynamic Mode, Static Mode, ALU 1-3 Mode, ALUS
Mode, Motorcycle Mode.
Self -calibrate function and Easy maintenance
includes free truck cone adapter set
includes plastic hood and quick release wing nuts
includes all accessories shown in the pictures
Gray power coat finish
Oversize 40mm Shaft and laser guide device indicated spot
where the weight attached on.
3. Product Installation
Remove Wheel Balancer from shipping crate and pallet.
Place Wheel Balancer on flat and stable floor.
Install the Safety hood.
Install threaded rod to spin rod extruding from side of the
machine using the hex bolt.
If Wheel Balancer shakes or moves while spinning the wheel, it
needs to be bolted to the ground to ensure proper function.
Electrical plug is preinstalled to fit North American 110 volt
electrical socket. Plug into proper electrical socket. Do not
hard wire directly to your electrical source. There is no power
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
6 / 24
surge protection on the machine. Please use a power surge
protector to ensure your machine is not damaged.
Install the wheel balancer in a dry and safe environment.
Exposure to moisture or extreme heat can damage the
components inside the wheel balancer.
4. Control Panel
A. Inside Unbalance Point
B. Inside Unbalance Display Window
C. Middle Static Unbalance Display Window
D. Sticking and Clamping Weight Position Indicator
E. Outside Unbalance Display Window
F. Outside Unbalance Point
G. Standard Dynamic Mode
H. Static Mode
I. ALU Mode
J. ALUS Mode
K. OPT Mode
L. Split/Hidden weight indicator
M. Mm/Inch Indicator
N. Motorcycle Mode
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
7 / 24
O. Wheel Parameters Input and Shift Key
P. Down Key
Q. Up Key
R. Enter Key
S. Dynamic/Static Mode Key
T. ALU Mode Key
U. OPT/HID Key
V. Measurement Unit Key
W. Start Key
X. Motorcycle Mode Key
Y. Fine Measurement Key
Z. Stop Key
This is the beginning screen that will be displayed when you first turn on
the machine:
(If set to Grams)
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
8 / 24
(If set to Ounces)
At anytime you may change from Ounces to Grams and back
by simply pressing the C button.
5. System Setting
This section shows the user how to change the various system
settings to meet their needs. You will need to check the settings and
adjust them accordingly before balancing a wheel.
Step 1: Hold down the “ENTER” button until you see:
You are now in the system settings mode.
Step 2: Use the UP and DOWN keys to navigate the different
setting selections. You will see that the display in the MIDDLE
STATIC UNBALANCE DISPLAY WINDOW:
Will change as each time you press the UP or DOWN keys.
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
9 / 24
Here are the descriptions for each system setting that can be changed:
Guard control setting: If set to “On” the machine
will not allow a wheel to spin while the safety hood is in the
up position. If set to “Off” the machine will ignore the safety
hood and will spin when the user presses START.
Standardization display setting: Set to 1g or 5g if using
grams to measure. Set to .10 Oz or .25 Oz if you are using
Ounces to measure. This sets the multiple in which the weight
will be displayed on the display board.
Least unbalance value setting. Set between 1 g-40 g
or .1 Oz-1.5 Oz. When the machine spins the wheel, any
unbalance amount less than your setting will display as 0.
Buzzer switch setting. Change to “On” or “Off” to control
the buzzer sound.
Width Input setting. Change width input to Grams
or Ounces. Grams will display “0.” and Ounces will display
“0.0”.
Diameter input setting. Change Diameter input to
Grams or Ounces. Grams will display “0.” and Ounces will
display “0.0”.
Unbalance unit of measurement. “Gr” means the unit will
display in grams.“OS” means the unit will display in ounces.
Phoenix Auto Equipment
-Address: 2711 East Craig Road Ste #E, North Las Vegas, NV, 89030 United States
- Website: https://www.phoenixautoequipment.com
- Phone: 7025802883
10 / 24
Step 3: Once you have found the system setting that you wish to
change, press the ENTER key. This will then allow you to change the
system setting to fit your needs. For example, the display will
change to:
To Change this setting to off, push the UP or DOWN arrow. Once
you have the setting correct to fit your needs, press the ENTER
button to return to the system settings main menu. You can now
use the UP or DOWN arrows to move to the next setting you wish
to change.
Step 4: Once you have made all the system setting changes you
need, press the WHEEL PARAMETERS INPUT AND SHIFT KEY
which looks like: .
This will save your changes and return you to the original
balancing screen. To exit the system settings without saving your
changes, press the STOP key.
Table des matières
