Philips 42PW9982 Manuel utilisateur

Information for users in the UK

(Not applicable outside the UK)

Positioning the TV

For the best results, choose a position where light does not fall directly on the screen, and at some distance away from radiators or

other sources of heat. Leave a space of at least 5 cm all around the TV for ventilation, making sure that curtains, cupboards etc.

cannot obstruct the air flow through the ventilation apertures.

The TV is intended for use in a domestic environment only and should never be operated or stored in excessively hot or humid

atmospheres.

General Points

Please take note of the section 'General Information' at the end of the English section in this booklet.

Interference

The Department of Trade and Industry operates a Radio Interference Investigation Service to help TV license holders improve

reception of BBC and IBA programmes where they are being spoilt by interference.

If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television and Radio Reception".

Mains connection

Before connecting the TV to the mains, check that the mains supply voltage corresponds to the voltage printed on the type plate on

the rear panel of the TV. If the mains voltage is different, consult your dealer.

Important

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows :

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved type.

In order to maintain conformity to the EMC directive, the mains plug on this product must not be removed.

Connecting the aerial

The aerial should be connected to the socket marked xat the back of the receiver. An inferior aerial is likely to result in a poor,

perhaps unstable picture with ghost images and lack of contrast. Make-shift loft or set-top aerials are often inadequate.

Your dealer will know from experience the most suitable type for your locality.

Should you wish to use the receiver in conjunction with other equipment, which connects to the aerial socket such as TV games, or

a video camera, it is recommended that these be connected via a combiner unit to avoid repeated connection and disconnection of

the aerial plug.

English

Contents

Your remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation

Search for and store TV channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Select the menu language and country . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Automatic installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Manual installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Give name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Reshuffle the programme list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Select favourite TV channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Install TV setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Define decoder/descrambler programme numbers . . . . . . . . . . . . . . . 9

The keys on the front of the receiver box . . . . . . . . . . . . . . . . . . . . . . 9

Operation

Use of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Use of the main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Picture menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Sound menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Features menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Dual Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Peripheral equipment

Connect Peripheral equipment and computer . . . . . . . . . . . . . . . . . . . 20

Select Peripheral equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Record with your videorecorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Lexicon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

EasyLink features are based on the "one touch

operation" approach. This means that a

sequence of actions are executed at the same

time in both the television and the video

casreceiverte recorder, if both are fitted with

the EasyLink function and connected with the

video recorder with the eurocable supplied.

VCR1

VCR2

DVD

AMP

TUNER

TAPE

SAT

Your remote control

p. 10 Vvolume key

¬sound temporarily

switched off

p. 10 qpicture format

p. 10 Xbilingual choice

p. 11 jcontinuous subtitles /

subtitle language selection

(DVD - Digital Video Disc)

p. 18 bteletext on/off

p. 17 Dual screen

- P+ channel selection

cswitching screens

dfreeze the subpicture

Bswitch to standby p. 10

ion screen info p. 10

0previous programme p. 10

Videorecorder p. 26

Digital Video Disc p. 26

Sfreeze the main picture p. 11

Preduce image noise

ﬁmosaic screen

spersonal preferences

Installation p. 4

yÚ

Aselect your choice p. 12

OK activate your choice

Pprogramme selection p. 10

Smart Controls

p. 11 picture and sound

settings

123

456

789

ce fh U

‡

ÏN

π†

PP cd

SPﬁs

T-C AUDIO

PICTURE SOUND

DVD SELECT DVD

p. 25 uselection of VGA, EXT1,

EXT2, EXT3 or FRONT

Mperipheral selection

TV TV selection

p. 17 bdual screen on/off

p. 12 PICTURE, SOUND, FEATURES

menus, programme list

Dolby Pro Logic menu

p. 18 direct txt page or subject selection

p. 18 Teletext

direct txt page or subject selection

kindex page selection

e interrupt

c mix tv/txt picture

henlarge

fsolution to riddles

Utime display

Preparation

Make sure that the wall mount (see wall mounting instructions

supplied) is being fixed securely enough so that it can carry at least

50 kg.

&Place the receiver box wherever you want, but leave at least 5 cm space free

all around the box for ventilation.

(E.g. on the ground, in a cupboard, behind a wall, in another room....)

éConnect one of the supplied aerial cables 1, and the DISPLAY POWER 3,

DISPLAY VIDEO 2, and SUBWOOFER 4cables as shown in the inside

frontcover of this handbook.

Make sure all screws of the cables 2and 3are tighted well.

“Check if the red loudspeaker button at the back of the receiver is in the

INTERNAL SPEAKERS position.

‘Connect the two Surround Sound rear loudspeakers supplied 5.

Always connect both Surround Sound loudspeakers: the left rear loudspeaker

at REAR L; the right rear loudspeaker at REAR R.

Push the connector clip down and insert the end of the wire into the opening: the

positive wire (the one with the black line) to the grey loudspeaker connection; the

negative wire to the black loudspeaker connection. Do not insert the wires too far.

The Surround Sound loudspeakers should always be located behind or to either side of

the listener. If preferred you can also hang the loudspeakers on the wall.

(To connect your computer, see p. 23.

To connect other peripherals, see p. 20.

In order to obtain the best result, please use only the supplied antenna cables

between the receiver box and videorecorder, and between videorecorder and

antenna connector.

§Insert the mains plug supplied 6into the power socket at the back of the

receiver and in the wall socket with a mains voltage of 220V-240V.

Please, only use the supplied rim-earthed mains cord with its built-in

suppressor to ensure safety and EMC.

èRemote control: Remove the cover of the battery compartment.

Insert the 2 batteries supplied (Type R03G-1,5V).

Press the TV key next to the display to be sure your remote control is in the

TV mode.

The batteries supplied do not contain the heavy metals mercury and cadmium.

Nevertheless in many countries exhausted batteries may not be disposed of with your

household waste. Please ensure you dispose of exhausted batteries according to local

regulations.

!Switch TV on : Press the power button Aon the front of the receiver.

A green indicator and the screen light up.

If the indicator is red, press the + P - key on the remote control.

The green indicator blinks every time you press a key on the remote control.

When you switch on your set for the first time, the MENU LANGUAGE automatically

appears on the screen. Alternatively the explanation appears in the different

languages.

EXTERNAL

FRONT

SPEAKERS

REAR

SPEAKERS

RO3 / AAA

Installation

Select the INSTALLATION MENU

&Open the door of the remote control.

éPress Sand sat the same time.

To use the menus

&Use the Akeys to select a menu or menu item.

éPress the OK key to activate.

“Press one of the colour menu keys on the door of the remote control to

return or to switch menu off.

π†

ÒC

‡

Sﬁs

TXT dfh U

yÚ

Menu Language

Country

Automatic Installation

Manual Installation

Give Name

Reshuffle

Favourite Programmes

Decoder/Descrambler

Setup

INSTALLATION

Menu Language

Country

Automatic Installation

Manual Installation

Give Name

Reshuffle

Favourite Programmes

Decoder/Descrambler

Setup

INSTALLATION

Store TV channels

First, you have to select your language and your country.

&Select the Menu Language in the INSTALLATION menu and press the

OK key.

éSelect your language and press the OK key.

“Select Country and press the OK key.

‘a. If you have your own aerial, select the country or part of the world from

where you want to receive the TV channel and press the OK key.

b. If you are connected to a cable system, select the country or part of the

world where you are now located and press the OK key.

You can now search for and store the TV channels in two different ways: using

automatic installation or manual installation (tuning-in channel by

channel).

•Select your choice and press the OK key.

Menu Language

Country

Automatic Installation

Manual Installation

Give Name

INSTALLATION

LANGUAGE English

... ...

••• ••• •••

COUNTRY UK

•••

••• •••

•••

Other

Automatic Installation

Searching O%.....................100%

AUTOMATIC

INSTALLATION

MANUAL

INSTALLATION

05 10

16 11

27 12

38 13

4 9 ...

(Selection Mode)

System

Programme No.

Store

Automatic installation

&In the Automatic Installation menu select On with the pπ keys to activate

the searching.

All TV channels are searched for and stored automatically.

Wait until the Searching bar at the bottom of the screen has disappeared.

If a cable system which broadcasts ACI (Automatic Channel Installation) or a

TV channel transmitting a teletext page with the frequencies and programme

names of all the TV channels which can be received, is detected, the search is

stopped and a programme list appears.

The programme list is automatically filled with all the programme numbers and

names of the TV channels transmitted.

It is possible that the cable company or the TV channel displays a broadcast selection

menu. Layout and items are defined by the cable company or the TV channel.

Make your choice with the Akeys and press the OK key.

éPress one of the colour menu keys on the door of the remote control to

return to the Installation menu.

Manual installation

Searching for and storing TV channels is done channel by channel.

You must go through every step of the Manual Installation menu.

Selection Mode is only present and lights up if the country you selected also

offers the channel option. (C-channels for aerial channels, S-channels for cable

channels.)

You can choose either channel or frequency mode.

&Select the TV system

•Select the country or part of the world from where you want to receive

the TV channel.

If you are connected to a cable system, select your country or part of the

world where you are now located.

éSearch for a TV channel

The frequency or the channel number increases until a TV channel is found.

In case of poor reception, you can improve the reception by adjusting the

frequency with the + P - key.

Direct selection of a TV channel

If you know the frequency, or the C- or S-channel number, enter the 3 digits of

the frequency directly with the digit keys 0 to 9.

“Enter the programme number

‘ Store steps &to “

•Select Store and press the OK key.

(Repeat the steps &to ‘to store another TV channel.

To exit from the menu

•Press one of the colour menu keys on the door of the remote control.

After the new or extra TV channel has been stored, the TV automatically transfers the

TV channel(s) to the video recorder provided with the EasyLink function.

The message : EasyLink : Downloading Presets ... appears at the bottom of the

screen.

The programme list of the video recorder is now equal to the one of the TV.

AUTOMATIC

INSTALLATION

0 10 ...

1 BBC1 11 ...

2 BBC2 12 ...

3 ITV 13 ...

4 ... .. ...

. ... .. ...

Automatic Installation Off

According to your preference you can change the order of the stored TV

channels.

&Select Reshuffle in the INSTALLATION menu and press the OK key.

éSelect the programme number you want to change.

Use the p or π keys to select another column of the programme list.

“Press the OK key.

‘Select the new number.

(Press the OK key again.

Repeat the reshuffling until all TV channels are allocated as you like.

§Press one of the colour menu keys to return to the INSTALLATION menu.

Reshuffle the programme list

RESHUFFLE 90

VGA 0

91 EXT1 1 BBC1

92 EXT2 2 BBC2

93 EXT3 3 ....

94 FRONT 4 ....

95 5 ....

96 .......

Select Favourite TV channels

FAVOURITE

PROGRAMMES

VGA 0 ... 10 ...

EXT1 1 ... 11 ...

EXT2 2 ... 12 ...

EXT3 3 ... 13 ...

FRONT 4 ... 14 ...

5 ... 15 ...

..... ......

Programme Number

Favourite

It is possible to change the name stored in the memory or to assign a name

to a TV channel which has not yet been entered. A name with up to 5 letters

or numbers can be given to the programme numbers 0 to 99. For example

SUPER, BBC1,... Between 99 and 0, in the column in the middle, you can also

name any peripherals that are connected.

&Select Give Name in the INSTALLATION menu and press the OK key.

éSelect the programme number.

“Press the OK key.

‘Select the character with the o or œ keys.

(Select the following position with the p or π keys.

§Select the following character.

èPress the OK key when finished.

!Press one of the colour menu keys to return to the INSTALLATION menu.

A space, numbers or other special characters are located between Z and A.

GIVE NAME 90

VGA 0

91 EXT1 1 BBC1

92 EXT2 2 BBC2

93 EXT3 3 ....

94 FRONT 4 ....

95 5 ....

96 .......

Give name

After leaving the installation you can browse through the TV channels by

pressing the + P - key. Only those TV channels which are in the favourite list

will be displayed. The non-favourite TV channels can still be selected with the

digit keys.

You can also do this for a programme number reserved for the programmes

you receive from your decoder.

&Select Favourite programmes in the INSTALLATION menu and press the

OK key.

éSelect your programme number.

“Select Favourite.

‘Select Yes or No.

(Repeat éto ‘for every TV channel you want to change into a favourite

or a non-favourite TV channel.

§Press one of the colour menu keys to return to the INSTALLATION menu.

Menu Language

Country

Automatic Installation

Manual Installation

Give Name

Reshuffle

Favourite Programmes

Decoder/Descrambler

Setup

INSTALLATION

&Select Setup in the INSTALLATION menu and press the OK key.

éUse the red menu key to return or to switch menu off.

Audio Output

If you have audio equipment connected to your receiver, you can select two

types of audio output.

•Select Variable with the por πkeys if you want to adjust the volume via

the TV when using your audio equipment to reproduce the TV sound signal. It

is possible that the volume control of the audio equipment needs to be

adjusted.

Select Constant if you want to adjust the volume with the volume control of

your audio equipment or if you want to record the sound of a TV programme

to an audio recorder (tape, DCC,...).

Ext2 Output

See Record with your video recorder without EasyLink, p. 27.

CD-i/Photo CD

See Connect Peripheral Equipment, Other equipments, p. 21.

Surround Mode

According to the broadcast sound modes, select the Surround Sound

possibilities:

Pro Logic with Dolby Pro Logic broadcasting. Nice effects can be reached in

Pro Logic mode with good stereo broadcasts.

Dolby 3 Stereo if no surround speakers are connected or if oversynthesized

sounds result in annoying surround effects.

Hall with mono or poor stereo broadcasting.

Off if you want to switch off Surround Sound.

Which loudspeakers are active, depends on the selected Surround mode.

See Dolby Pro Logic Install, p. 14.

Note: If you have only connected a right and left external loudspeaker and no centre

speaker, select Pro Logic and not Dolby3 Stereo in the Surround Mode menu

item. See also Centre mode, Phantom selection.

Centre Mode (only selectable in Dolby 3 Stereo or Pro Logic when you have

connected and selected external loudspeakers)

With internal speakers: the item centre mode can not be selected.

With external speakers: (external left and right loudspeakers and a centre

loudspeaker. See Connect Peripheral Equipment, External Loudspeakers, p. 22)

Note : Do not forget to put the red loudspeaker button at the back of the receiver in

the EXTERNAL SPEAKERS position.

•When in Surround Mode you have selected Pro Logic, you can select

Normal, Phantom or Wide in the Centre Mode;

•When in Surround Mode you have selected Dolby 3 Stereo, you can select

Normal or Wide in the Centre Mode;

•Select Phantom if no external centre speaker is connected;

•Select Normal if you have connected a small centre speaker which can not

reproduce low frequencies (< 100 Hz);

•Select Wide if you have connected a full range external centre speaker.

Install TV setup

Menu Language

Country

Automatic Installation

Manual Installation

Give Name

Reshuffle

Favourite Programmes

Decoder/Descrambler

Setup

INSTALLATION

Audio Output

Ext2 Output

CD-i/Photo CD

Surround Mode

Centre Mode

Ext Amplifier

Information Line

Ext 2 Input

VCR type

Picture mute

SETUP

External amplifier

This menu item can only be selected in case you did NOT select external

loudspeakers (with the red loudspeaker button at the back in INTERNAL

SPEAKER position).

•Select No: - if you did not connect an audio amplifier at the back of your

receiver. The menu item Centre Mode can not be selected;

- if you want to make a sound recording from your TV on an

audio recorder. See also Audio Output;

- if you do not want to use the external audio amplifier for

reproduction of the left and right channel of the Dolby signal.

•Select Yes: - if you connected an audio amplifier to AUDIO L and Rat the

back of your receiver, see Connect Peripheral Equipment,

Audio Equipment, p. 21, and you want to enjoy even more

impressive sound.

All TV loudspeakers only function as centre speaker and the

speakers connected to the audio amplifier reproduce the left

and right channel.

The menu item Audio Output can not be selected.

In the menu item Centre Mode you can select either Normal

or Phantom (the sound from the centre speaker is reproduced

via the left and right loudspeakers of the amplifier).

Information Line

After the selection of a TV programme or after pressing the ikey on the

remote control, a TV channel which broadcasts teletext may transmit the

name of the TV channel or the programme name or another message which

appears briefly in the information line at the bottom of the screen.

When selected Off, the information line will only appear after pressing the

ikey, and not after the selection of a TV channel.

Ext2 Input

See Connect Peripheral Equipment, Video recorder, p. 21.

VCR type

See Connect Peripheral Equipment, Video recorder, p. 21.

Picture mute

•Press the por πkeys to select a Blue or Black screen when there is no

picture or information.

•Press of the colour menu keys.

The INSTALLATION menu reappears.

Fast exit from the menus

•Press one of the colour menu keys repeatedly to switch off all menus.

Autres manuels pour 42PW9982

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philips TV

Philips

Philips 24PFS5603/12 Manuel utilisateur

Philips

Philips 7506 Series Manuel utilisateur

Philips

Philips 27PT31B1 Manuel utilisateur

Philips

Philips 29PT5645 Manuel utilisateur

Philips

Philips 39PHS6707 Manuel utilisateur

Philips

Philips 21PT2252 Manuel utilisateur

Philips

Philips 29PT9131/12 Manuel utilisateur

Philips

Philips Matchline 28PW9308/05 Manuel utilisateur

Philips

Philips 20PT6441 Manuel utilisateur

Philips

Philips 7908 Series Manuel utilisateur

Philips

Philips Matchline 36LM8908 Manuel utilisateur

Philips

Philips 5800 SERIES Manuel utilisateur

Philips

Philips 32PFL66X6H Manuel utilisateur

Philips

Philips LC4.2HE Manuel utilisateur

Philips

Philips Magnavox TS3260CI Manuel utilisateur

Philips

Philips Matchline 28PW960A Manuel utilisateur

Philips

Philips 8217 Series Manuel utilisateur

Philips

Philips 37HF7005/93 Manuel utilisateur

Philips

Philips 7906 Series Manuel utilisateur

Philips

Philips 20PT2321 Manuel utilisateur

Philips

Philips Matchline 28PW9617 Manuel utilisateur

Philips

Philips 37TA2800/79 Manuel utilisateur

Philips

Philips 50PUS7506 Manuel utilisateur

Philips

Philips 21PT5207/60 Manuel utilisateur

Manuels TV populaires d'autres marques

Toshiba

Toshiba 27A10 Manuel utilisateur

Hitachi

Hitachi 32FX48B Manuel utilisateur

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manuel utilisateur

Changhong Electric

Changhong Electric uhd55b6000is Manuel utilisateur

Panasonic

Panasonic Genus TX-G10 Manuel utilisateur

Toshiba

Toshiba 19A20 Manuel utilisateur

Sony

Sony XBR-100Z9D Manuel utilisateur

Samsung

Samsung 55S9 B Series Manuel utilisateur

Sharp

Sharp LC-40FI5012E Manuel utilisateur

Loewe

Loewe Table Stand Reference 55 Manuel utilisateur

Sylvania

Sylvania 6427FB Manuel utilisateur

Sanyo

Sanyo CE19LD90N-B Manuel utilisateur

North State

North State TV2GO Manuel utilisateur

RCA

RCA RTU7877 Manuel utilisateur

Sharp

Sharp 21K-FG1RU Manuel utilisateur

Sony

Sony Esprit TAV-L1 Manuel utilisateur

Grundig

Grundig 43 VLE 4820 Manuel utilisateur

Samsung

Samsung LN26C350D1D Manuel utilisateur