Philips CARD01 Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Philips Accessoires TV

Philips

Philips SCANCARD II Manuel utilisateur

Philips

Philips SWA3554 Manuel utilisateur

Philips

Philips SWV2559W Manuel utilisateur

Philips

Philips Flavors 22FDF2023 Manuel utilisateur

Philips

Philips Flavors 32FDF1013 Manuel utilisateur

Philips

Philips SWV3804NZ Manuel utilisateur

Philips

Philips SWV2187W Manuel utilisateur

Philips

Philips SWV2259W Manuel utilisateur

Philips

Philips SWV3561 Manuel utilisateur

Philips

Philips SWV2142W Manuel utilisateur

Philips

Philips SWW1890/27 Manuel utilisateur

Philips

Philips UHP/915B455011 Manuel utilisateur

Philips

Philips SWV2081W Manuel utilisateur

Philips

Philips SVC4255G/10 Manuel utilisateur

Philips

Philips Wireless TV link SBCVL1400/05 Manuel utilisateur

Philips

Philips SQM6325/00 Manuel utilisateur

Philips

Philips Flavors 42FDF1023 Manuel utilisateur

Philips

Philips SWW1800/12 Manuel utilisateur

Philips

Philips Flavors 42FDF4023 Manuel utilisateur

Philips

Philips Flavors 42FDF7013 Manuel utilisateur

Philips

Philips TC32PV2 Manuel utilisateur

Philips

Philips 22PP1152 Manuel utilisateur

Philips

Philips SVC1116F/27 Manuel utilisateur

Philips

Philips SVC3222G/10 Manuel utilisateur

Manuels Accessoires TV populaires d'autres marques

pass & seymour

pass & seymour GFCI Manuel utilisateur

Skyvue

Skyvue SECURITY ALARM DEVICE Manuel utilisateur

Niles

Niles C5-RFWM Manuel utilisateur

Sony

Sony CRU-52X1 Manuel utilisateur

Sony

Sony BRAVIA KDL-46Z4100/S Mode d’emploi

BVE

BVE MATRIX 7xe Manuel utilisateur

Epson

Epson Moverio BT-100 Manuel utilisateur

Alcatel

Alcatel onetouch v100 Manuel utilisateur

Flow

Flow 836 ONT Manuel utilisateur

AIRIS

AIRIS G819 Manuel utilisateur

Loewe

Loewe Digital Recorder + Manuel utilisateur

Sceptre

Sceptre Stello Manuel utilisateur

Goodmans

Goodmans GD11FVRSD32 Manuel utilisateur

Serene

Serene TVDirect TV-95 Manuel utilisateur

TRUlink

TRUlink 89000 Manuel utilisateur

Panasonic

Panasonic DigiCard Manuel utilisateur

Alpine communications

Alpine communications Roku Device Manuel utilisateur

LEGRAND

LEGRAND SANUS BSA-IWP801 Manuel utilisateur

PHILIPS CLONE EXTENDER CARD

CARD01

Description: This Clone Extender Card is intended to be used on Card Model TV’s whenever there is a

need to use the Smart Loader RL5180 to program the set. It is not possible to use the

RL5180 Smart Loader to program a Card TV without using the Clone Extender Card

(CARD01). The RJ11 jack on the Card that originally came in the TV is not for using a

Smart Loader. This RJ11 jack is for DCM (Data Communication Module) applications.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT

TO RAIN OR MOISTURE.

CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert.

ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la

borne correspondante de la prise et pousser jusqu’au fond.

HOW TO USE THE CLONE EXTENDER CARD

1. Unplug the TV’s AC power cord from the power source.

2. The Card Door is located on the rear of the TV cabinet and slides over the antenna connector.

Remove the two screws that hold the Card Door to the TV cabinet. Remove the Card Door from the

back of the TV cabinet.

a. If a Card is in the TV, there is a wire that connects the TV Tuner and the Card. Disconnect

the wire from the Card. Remove the Card by sliding it backward toward the rear of the TV.

(The Card plugs into a 32 pin connector.)

b. If there is not a Card in the TV, go to the next step.

3. To install the Clone Extender Card: Turn the Card solder side up with the 32 pin connector facing

the Card slot opening.

CAUTION: THE CARD MUST BE PLUGGED IN SOLDER SIDE UP AND COMPONENT SIDE

DOWN.

4. Slide the Card into the opening, (use the slots on the left and right of the opening to guide the Card

in) attaching it to the 32 pin connector inside the TV. Plug the TV’s AC power cord into the power

source.

5. Plug RL5180 Smart Loader into the 6 pin connector (RJ11) on the Clone Extender Card. Follow the

instructions supplied with the RL5180 Smart Loader to program the TV. When the Smart Loader

operation is completed, unplug the TV from the AC power source and replace the original Card and

Card Door cover. Ensure the TV operation is normal.

st

CAUTION

ATTENTION

This “bolt of lightning” indicates

uninsulated material within your unit

which may cause an electrical shock. For

the safety of everyone in your household,

please do not remove product covering.

The “exclamation point” calls

attention to features for which you

should read the enclosed literature closely

to prevent operating and maintenance

problems.

3135 015 16011