Philips 46PP9501/05 Manuel utilisateur

Information for users in the UK

(Not applicable outside the UK)

Positioning the TV

For the best results, choose a position where light does not fall directly on the screen, and at some distance away from radiators

or other sources of heat. Leave a space of at least 5 cm all around the TV for ventilation, making sure that curtains, cupboards etc.

cannot obstruct the air flow through the ventilation apertures.

The TV is intended for use in a domestic environment only and should never be operated or stored in excessively hot or humid

atmospheres.

General Points

Please take note of the section 'Tips' at the end of the English section in this booklet.

Interference

The Department of Trade and Industry operates a Radio Interference Investigation Service to help TV license holders improve

reception of BBC and IBA programmes where they are being spoilt by interference.

If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television and Radio Reception".

Mains connection

Before connecting the TV to the mains, check that the mains supply voltage corresponds to the voltage printed on the type plate

on the rear panel of the TV. If the mains voltage is different, consult your dealer.

Important

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows :

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS1362 5A,A.S.T.A. or BSI approved type.

In order to maintain conformity to the EMC directive, the mains plug on this product must not be removed.

Connecting the aerial

The aerial should be connected to the socket marked xat the back of the set. An inferior aerial is likely to result in a poor,

perhaps unstable picture with ghost images and lack of contrast. Make-shift loft or set-top aerials are often inadequate.

Your dealer will know from experience the most suitable type for your locality.

Should you wish to use the set in conjunction with other equipment, which connects to the aerial socket such as TV games, or a

video camera, it is recommended that these be connected via a combiner unit to avoid repeated connection and disconnection of

the aerial plug.

Loop aerial (if provided)

The loop aerial packed with the set will give satisfactory reception under good signal conditions. Fit the aerial bracket and lead by

pushing the peg into the square hole in the backcover until it latches in place. Then insert the plug on the lead into the aerial

socket.

Contents

English

Your remote control 2

Preparation 3

Installation 4

Store TV channels 4

Select the menu language and country 4

Automatic installation 5

Manual installation 5

Give name 6

Reshuffle the programme list 6

Select favourite TV channels 6

Install TV setup 7-8

EasyLink features are based on the “one touch operation” approach.This

means that a sequence of actions are executed at the same time in both

the television and the video cassette recorder, provided both are fitted

with the EasyLink function and connected with the eurocable

supplied with your video recorder.

Installation

Operation

Use of the remote control 9-11

Use of the menus

Picture menu 12

Sound menu 12-15

Features menu 16

NEXTVIEW 17-21

Teletext 22-24

Keys on front of the TV 24

Connect peripheral equipment

Connecting and selecting equipment 25-29

Remote control functions for peripherals 29-30

Recording 31

Tips 32

Index 32

Glossary 33

2Preparation

Mha

SMART

ACTIVE

CONTROLSMART

213

546

879

®Ò‡π

†

æb

Mqa

MOVIE SPORT CHILD NEWS OTHER

VCR DVD SAT

TUNER CD

OK MENU

TAPE CDR

SMARTSMART

PICTURESOUND

¬V P

◊

fh Uf

yÚ

pπ

yÚ

®q

bﬁcd

INSTANT

ZOOM

Preparation

Your remote control

Teletext p. 23

Utime display/subpage selection

fsolution to puzzles

display PDC/VPS code

henlarge

Preduce image noise p. 11

Smart Controls

Msmart sound p. 10

hactive control p. 10

asmart picture p. 10

Dual Screen p. 10

bdual screen on

cno function

dstill teletext picture

ﬁstrobe

Bswitch to standby p. 9

ion screen info p. 9

0previous programme p. 9

◊video recorder/DVD function p. 9

Xbilingual choice/sound info p.11

TXT language group selection p. 23

EasyLink p. 11

®INSTANT recording

qpicture format p. 11

bteletext on/off p. 22

Ïmain menu on/off p. 9

cursor to select

your choice p. 12

Installation p. 4

Vvolume up/down p. 9

¬sound mute p. 9

Pprogramme selection p. 9

Peripherals p. 29

wselection of EXT1,EXT2,EXT3

or FRONT

TV, videorecorder (VCR), DVD,

Satellite (SAT), TUNER,CD,TAPE or

cd-recordable (CDR) selection.

Colour keys

- select TV channels by theme p. 11

- direct teletext page or

subject selection p. 23

Video recorder/DVD player/Satellite

p. 29-30

Ono function

Sfreeze the picture p. 9

hold teletext page p. 23

Qsurround modes p. 9

æNEXTVIEW on/off p. 9

OK activate your choice

Place the TV on a solid surface.

For ventilation, leave at least 5 cm free all around the TV.

To prevent any unsafe situations, do not place any objects on top of the TV.

Avoid heat, direct sunlight and exposure to rain or water.

éInsert the aerial plug firmly into the aerial socket xat the back of the

TV. For best picture quality use the suppressor-aerial cable supplied.

“Insert the mains plug in the wall socket having a mains voltage of 220V-240V.

To prevent damaging the mains (AC) cord which could cause a fire or electric

shock, do not place the TV on the cord.

‘Remote control: Remove the cover of the battery compartment.

Insert the 2 batteries supplied (Type R6-1,5V).

Press the TV key to be sure your remote control is in the TV mode.

The batteries supplied do not contain the heavy metals mercury and cadmium.

Nevertheless in many countries exhausted batteries may not be disposed of with

your household waste. Please check on how to dispose of exhausted batteries

according to local regulations.

Note: this remote control functions with TVs which use the RC6 signalling standard.

(Switch TV on : Press the power switch Aon the front of your TV.

A green indicator on the front of the TV and the screen light up. If the

indicator is red, press the -P+ key on the remote control.

Normally, the TV will display a picture on screen in 10-15 seconds.

A yellow indicator appears when the TV is in electronic program guide

acquisition mode. If no data is detected the indicator will change to red after

the system is finished checking for information.

The green lamp blinks every time you press a key on the remote control.

When you switch on your set for the first time, the menu LANGUAGE

automatically appears on the screen. Alternatively the explanation appears in the

different languages. Choose your own language and press the OK key on the

remote control.

Go on to page 4.

3Preparation

Preparation

CABLE

R6 / AA

æb

VCR

MOVIE OTHERNEWSCHILDSPORT

TV DVD SAT

CDTUNER TAPE CDR

4Installation

Store TV channels

After the new or extra TV channels have been stored, the TV automatically transfers

those TV channels to the video recorder if it is equipped with the EasyLink function.

The message EasyLink : Downloading ...... appears on the screen. The

programme list of the video recorder is now the same as the one of the TV. If the TV

is connected to a video recorder which supports the NEXTVIEWLink function, the TV

also automatically transfers the language and country selections to the video

recorder.

First, select your language and country.

Select Menu Language and press the OK key.

éSelect your language and press the OK key.

Use the cursor up/down to scroll through the list and to bring up other

languages which are not displayed on the screen at present.

“Select Country and press the OK key.

‘Select the country where you are now located and press the OK key.

Use the cursor up/down to scroll through the list and bring up other

countries which are not displayed on the screen at present.

Select Other when none of the countries applies.

You can now search for and store the TV channels in two different ways:

using automatic installation or manual installation (tuning-in channel by

channel).

Select your choice and press the OK key.

Select the menu language and country

MENU TITLE

Menu language

Country

Automatic Installation

JINSTALLATION

MENU TITLE

United Kingdom

....

JCOUNTRY

MENU TITLE

English

....

JMENU LANGUAGE

Open the door of the remote control.

éPress Uand fat the same time.

Installation

Select the INSTALLATION menu

Use the cursor in the up/down, left/right direction to select a menu item.

éPress the OK key to activate.

“Use the Ïkey to return or to switch the menu off.

To use the menus

MENU TITLE

Subject 1

Subject 2

Subject 3

JSubject 4

Subject 5

Subject 6

JSubject 4 L M

pπ

213

546

879

◊

X®qP

yÚ

ZOOM

INSTANT

213

æb

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

MOVIE OTHERNEWSCHILDSPORT

OK MENU

select menu item

return or switch

main menu off

activate

Searching for and storing TV channels is done channel by channel.

You must go through every step of the Manual Installation menu.

Selection Mode is only present and lights up if the country selected also

offers the channel option (C-channels for aerial channels, S-channels for cable

channels).

You can choose either channel or frequency mode.

Select the TV system

Select the country or part of the world from where you want to receive the

TV channel.

If you are connected to a cable system, select your country or part of the

world where you are now located.

éPress the cursor down and enter the programme number with the digit keys.

“Search for a TV channel

Press the cursor left/right.

The frequency or the channel number increases until a TV channel is found.

Direct selection of aTV channel

If you know the frequency, the C- or S-channel number, enter it directly with

the digit keys 0 to 9.

Ask for a list from your cable company or dealer, alternatively consult the

Table of frequencies on the inside backcover of this handbook.

‘Fine tune

In case of poor reception, you can improve the reception by adjusting the

frequency with the cursor left/right.

(Store steps to ‘

Select Store and press the OK key.

Repeat every step to store another TV channel.

§To exit from the menu press the Ïkey on the remote control.

In the Automatic Installation menu select Start and press the OK key to

activate the searching. All TV channels are searched for and stored

automatically.

If a cable system which broadcasts ACI (Automatic Channel Installation) or a

TV channel transmitting a teletext page with the frequencies and programme

names of all the TV channels which can be received, is detected, the search is

stopped and a programme list appears.

The programme list is automatically filled with all the programme numbers

and names of the TV channels transmitted.

It is possible that the cable company or the TV channel displays a broadcast

selection menu. Layout and items are defined by the cable company or the TV channel.

Make your choice with the cursor and press the OK key.

To exit from the menu press the Ïkey on the remote control.

Go on to page 6.

5Installation

Manual installation

Automatic installation

Automatic Installation

Start

Stop

TV is searching

One moment please ...

JStop K

Automatic Installation

Start

Stop

1 BBC1

2 BBC2

3 CNN

....

JStart K

Manual Installation

(Selection Mode)

System

Programme No.

Fine tune

Store

JSystem K

6Installation

Give name

It is possible to change the name stored in the memory or to assign a name

to a TV channel which has not yet been entered.A name with up to 5 letters

or numbers can be given to the programme numbers 0 to 99. For example

SUPER, BBC1,...

Between 99 and 0 you can also name any peripherals that are connected.

Select Give Name in the INSTALLATION menu and press the OK key.

éSelect the programme number.

“Press the OK key.

‘Select the character with the cursor up/down.

(Select the following position with the cursor left/right.

§Select the following character.

èPress the OK key when finished.

!Press the Ïkey to return to the INSTALLATION menu.

A space, numbers or other special characters are located between Z and A.

According to your preference you can change the order of the stored TV

channels.

Select Reshuffle in the INSTALLATION menu and press the OK key.

éSelect the programme number you want to exchange.

“Press the OK key.

‘Select the new number you want to exchange with the first selected one.

(Press the OK key.

Repeat the operation until all TV channels are allocated as you like.

§Press the Ïkey to return to the INSTALLATION menu.

Reshuffle the programme list

After leaving the installation you can browse through the TV channels by

pressing the - P + key. Only those TV channels which are in the favourite list

will be displayed.The non-favourite TV channels can still be selected with the

digit keys. By default all stored channels are added in the favourite list.

Select Favourite programmes in the INSTALLATION menu and press

the OK key.

éSelect your favourite programme number.

“Select Yes or No with the cursor left/right.

‘Repeat for every TV channel you want to change into a favourite or a

non-favourite TV channel.

(Press the Ïkey to return to the INSTALLATION menu.

For a proper functioning of NEXTVIEW, the first TV channel from the favourite list

should also broadcast the correct date and time via teletext.

Select Favourite TV channels

INSTALLATION

Menu Language

Country

Automatic Installation

Manual Installation

Give Name

Reshuffle

Favourite Programmes

SETUP

JGive Name

Give Name

EXT1

EXT2

EXT3

FRONT

1 BBC1

2 BBC2

3 ....

4 ....

5 ....

Reshuffle

EXT1

EXT2

EXT3

FRONT

1 CNN

2 BBC2

3 ....

4 ....

5 ....

J1 CNN

Favourite programmes

0 ... No

1 ... Yes

2 ... No

3 .... No

4 .... Yes

5 ....

J2 ... Yes

7Installation

The Setup menu allows you to set up those settings which are considered as

only once and which are not related to the installation of the TV channels.

The Setup menu contains items that control the settings of the TV’s functions

and features, services and peripherals you may have connected.

Use the cursor in the up/down, left/right direction to select the menu item.

éUse the OK key to activate.

“Use the Ïkey to return or switch menu off.

Digital sources

See Connect Peripheral Equipment, p. 26 to connect your digital equipment,

like a DVD, satellite tuner or a similar digital device.

Define Decoder/Descrambler programme numbers

If a decoder or a descrambler is connected, see p. 25, you can define one or

more programme numbers as decoder programme numbers.

Press the cursor left/right to select the input used to connect to your

decoder Off,EXT1 or EXT2.

Select Off if you do not want the selected programme number being

activated as a decoder programme number.

Select EXT2 when the decoder is connected to your EasyLink video recorder.

When selecting the decoder, the message EasyLink: Downloading Presets....

appears on the screen.

Dynamic Bass Enhancement (DBE)

Select DBE with the cursor up/down.

Press the cursor left/right to adjust the DBE control.When selected On, DBE

increases the low frequency audio range for the playback of TV sound.

Information Line

Select On and after the selection of a TV programme or after pressing the

ikey on the remote control, a TV channel which broadcasts teletext may

transmit the name of the TV channel, the programme name or another

message.This is displayed on screen next to information about sound, picture

format and DNR setting.

When selected Off, only sound, picture format and DNR information is

displayed after the selection of a TV channel or after pressing the ikey.

Factory settings

Select Factory settings and press the OK key to restore picture and sound

settings, predefined in the factory.

Extra front speakers

See Connect Extra loudspeakers,Amplifier, p. 27.

If no extra front speakers/amplifier are connected, do not change the

predefined factory setting which is No (TV).

Rear speakers

See Surround Settings Menu, p. 13.

If no rear speakers are connected, do not change the predefined factory

setting which is No (TV).

Install TV Setup

INSTALLATION

Menu Language

Country

Automatic Installation

Manual Installation

Give Name

Reshuffle

Favourite Programmes

SETUP

JSETUP

Decoder/Descrambler

Programme

Decoder Status

JProgramme

SETUP

Digital Sources

Decoder/Descrambler

Information line

Factory settings

Extra front speakers

Rear Speakers

Auto surround on/off

NEX

IEW

provider none, 0...99

Auto Format yes/no

DBE

INSTALLATION

JDigital sources

8Installation

Auto surround

Sometimes the broadcaster transmits special signals for Surround Sound

encoded programmes.

Dependent on your speaker configuration, the TV automatically switches to

the best surround sound mode when Auto Surround is switched On.

When rear speakers are connected and selected, Dolby Pro Logic will be

reproduced.When no rear speakers are connected, Dolby Virtual will be

reproduced. Overruling this surround mode remains possible.

NEXTVIEW provider

Most broadcasters in Europe are offering teletext pages containing the days

programme schedule.These pages can be requested by switching the TV to

Teletext Guide.

An increasing number of broadcasters are offering an extended programme

guide service called NEXTVIEW.

NEXTVIEW is a new way of presenting programme schedules and offers more

features than basic teletext.With NEXTVIEW it is possible to show for instance

all the movies or children programmes coming tonight or on following days.

If you select None as NEXTVIEW provider, the TV will capture all data from

the available TV channels which broadcast NEXTVIEW. Broadcaster defined

menus will not be available.

If you select a programme number of a TV channel stored in the favourite list

as NEXTVIEW provider, the selected TV channel will provide NEXTVIEW data

and additional info of its own broadcasts as well as from other (non selected)

TV channels.

Normally you will select as NEXTVIEW provider the TV channel that transmits

most information in your language.You can make the best selection via info

from TV announcements or from the newspapers.

Important:

For a proper functioning of NEXTVIEW, the first TV channel from the favourite list

should also broadcast the correct date and time via teletext.

Please check at startup if the time and date are correct in the NEXTVIEW screen.

Remark:

Not all TV channels support NEXTVIEW.

How to make use of NEXTVIEW, see p. 17.

Auto Format

Selecting Auto FormatYes, the screen will automatically be filled as much as

possible with the picture when TV programmes are not carrying special

signals detecting the correct screen format.

With the qkey on the remote control you can still select other picture

formats. See p. 11.

Installation

Select Installation and press the OK key to return immediately to the

INSTALLATION menu.

‘To exit from the menu press the Ïkey repeatedly.

SETUP

Digital Sources

Decoder/Descrambler

Information line

Factory settings

Extra front speakers

Rear Speakers

Auto surround on/off

NEX

IEW

provider none, 0...99

Auto Format yes/no

DBE

INSTALLATION

NEX

IEW

provider none/o...99

9Use of the remote control

Operation

Use of the remote control

Mha

SMART

ACTIVE

CONTROL

SMART

PICTURESOUND

213

546

879

®Ò‡π

†

æb

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

◊

MOVIE SPORT CHILD NEWS OTHER

OK MENU

wSelect peripherals

Press this key repeatedly to select EXT1,

EXT2, EXT3 or FRONT, according to where

you connected the peripherals (p. 29).

TV VCR DVD SAT TUNER CDTAPE CDR

Press one of these keys to use the remote

control directly in the TV, video recorder,

DVD or satellite mode. A green led lights up.

Press the same key again within 3 seconds to

use the remote control in the mode

indicated below the key (tuner, CD, tape or

CD-recordable).A red led lights up.

Press the key again to return to the function

mentioned above the key.

BStandby

The set is switched off and the red indicator

(yellow in the case of NEXTVIEW info

acquisition) lights up. In case of NEXTVIEW

acquisition the TV is switched to full

standby after max. 1 hour and the red

indicator lights up.

To switch the TV on again, press - P + or the

digit keys.

If your EasyLink video recorder has the

system standby function and you press the

standby key for 3 seconds, both the TV and

video recorder are switched to standby.

®Ò‡π†Video recorder see p. 29

æNEXTVIEW on/off see p. 17

OK Press this key to activate your choice in

the menus.

SFreeze

To activate/de-activate the frozen picture and

to hold a teletext page.

QSurround mode

Press this key repeatedly to select another

surround mode: Pro Logic, Dolby Virtual,

Dolby 3 Stereo, Stereo or Hall.

iScreen information

Press for 5 seconds to activate/de-activate

the extended or reduced display of TV

channel and programme information on the

screen.

Press briefly to display information about the

selected TV channel and programme, the

sound reception, picture settings, the selected

DNR setting and the remaining time set with

the sleeptimer.

0/9 Digit keys

To select a TV channel.

For a two digit programme number, enter the

second digit within 2 seconds.

To switch immediately to a selected one digit

TV channel, keep the digit key pressed a bit

longer.

0Previous programme

The previously selected TV channel is

displayed.

The ◊indication has a video recorder/DVD

function.

Use of the remote control

bTeletext on/off see p. 22

ÏMain menu on/off see p. 12

VVolume

Press + or - to adjust the volume.

¬ Mute key

Temporarily interrupt the sound or restore

it.

PProgramme selection

To browse through the TV channels

activated in the Favourite Programme menu.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philips Téléviseur à projection

Philips

Philips 43PP9202 Manuel

Philips

Philips 43PP8421 Manuel

Philips

Philips 50PL9220D Manuel utilisateur

Philips

Philips Magnavox 8P5434C Manuel utilisateur

Philips

Philips 54XP43C/37 Manuel utilisateur

Philips

Philips MAGNAVOX TP4830 Manuel utilisateur

Philips

Philips MX5471 Manuel utilisateur

Philips

Philips 9P6440C Manuel utilisateur

Philips

Philips 55PP950299 Manuel utilisateur

Philips

Philips 55PP9363H Manuel utilisateur

Philips

Philips 9P5044C1 Manuel utilisateur

Philips

Philips Magnavox 9P5514C Manuel d'utilisation

Philips

Philips 64P8341 Manuel utilisateur

Philips

Philips 8P4841C Manuel utilisateur

Philips

Philips 64P834299 Manuel

Philips

Philips 51PP9100D - Hook Up Guide Manuel utilisateur

Philips

Philips 60PP9910/17B Guide de l'utilisateur

Philips

Philips 60PP 9601 Manuel utilisateur

Philips

Philips Magnavox 8P5444C Manuel utilisateur

Philips

Philips 60PW9363/17 Manuel utilisateur

Philips

Philips 55PP9352 Manuel utilisateur

Philips

Philips 60PP9363 Manuel utilisateur

Philips

Philips 43998320 Manuel utilisateur

Philips

Philips Magnavox 9P5031C Manuel utilisateur

Manuels Téléviseur à projection populaires d'autres marques

Samsung

Samsung ST-43T6P Manuel utilisateur

Toshiba

Toshiba ColorStream TP50G60 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric WD-65734 Manuel utilisateur

Optoma

Optoma EP652A Manuel utilisateur

Samsung

Samsung SP43T8HPX/XEC Manuel utilisateur

Sony

Sony KP-57WS500 - 57" Hi-scan 1080i™ 16:9 Projection... Guide de l'utilisateur

Hitachi

Hitachi 51F510 Manuel utilisateur

RCA

RCA P52950 Manuel utilisateur

Sony

Sony KP-51DS1U Manuel utilisateur

Magnavox

Magnavox 51MP392H - 51" Widescreen Hd Ready Tv Manuel utilisateur

Hitachi

Hitachi 46F510 Manuel utilisateur

Pioneer

Pioneer Elite PRO 510HD Manuel utilisateur

JVC

JVC I'Art Pro AV-48P776 Manuel utilisateur

Sony

Sony GRAND WEGA KDF-55XS955 Manuel utilisateur

Sony

Sony KP-46WT520 - Wide Screen Projection Tv Manuel utilisateur

Toshiba

Toshiba 42HM66 - 42" Rear Projection TV Manuel utilisateur

Hitachi

Hitachi 51S715 Manuel utilisateur

Samsung

Samsung HC-P5256W Manuel utilisateur