Philips SimplyGo Manuel utilisateur

SimplyGo

Quick-start guide

This guide is intended to help you get started using the SimplyGo

portable oxygen concentrator. If you have questions that are not

answered in this guide, please consult the SimplyGo User Manual

or contact your homecare provider.

Getting started

Charge the battery using the AC power cord.

Before using SimplyGo for the first time, the battery requires an

initial uninterrupted charging time of four hours minimum. This can

be accomplished by installing the battery (see step 2 of Quick-start

instructions) and using the AC power cord.

To charge the battery using the AC power cord provided with your

system, follow these steps:

1. Connect the AC power supply’s output cable to the SimplyGo power

input connector located on the upper right side of the unit.

2. Connect the AC power cord’s connector to the AC power supply.

3. Connect the AC power cord’s plug to an AC outlet.

Important: The first time you charge the battery, be sure to charge it fully.

Do not use the DC power cord for initial charge; instead use AC power.

Control panel display

1. Power Turns SimplyGo on and off

2. Alarm silence Turns the audible alarm off

3. Mode Selects one of the three possible operating modes

4. Display screen Shows information about the operating

status of the device

5. Plus (+)/minus (-) + Increases the displayed setting;

- Decreases the displayed setting

6. Cannula connector Oxygen output and connection

point for cannula

1 2 3 4 5 6

1. Attach the shoulder strap to

the carrying case.

Slide SimplyGo into carrying case,

secure, and attach shoulder strap if

desired. SimplyGo can be operated in

or out of the case.

2. Insert the charged battery into

the device.

There is only one way the battery can be

inserted into SimplyGo. Using its handle,

position the battery over the battery

compartment, lower into place, and press

until it snaps into place. After the battery

is inserted, check to make sure the

battery handle is level with or slightly

below the top of the plastic case.

3. Connect a nasal cannula to the

oxygen outlet on top of the device.

Connect a nasal cannula to the top of

SimplyGo. To avoid a disruption of oxygen,

route the cannula so that it is not pinched

or kinked. A standard single lumen nasal

cannula and tubing should be used.

SimplyGo works with cannula tubing up to

30 ft. (9 m).

Quick-start instructions

4. Turn on SimplyGo.

Turn the device on by pressing the

Power button twice. After the first

press, the display screen and the button

backlights turn on. Press the Power

button a second time to place the device

in operating mode. This second

press helps prevent unwanted starts

or inadvertent changes in oxygen flow.

The introductory screen momentarily

appears followed by the final operating

mode screen.

5. Set the mode.

Press the Mode button. Note: If the

device is operating and the screen

is dark, the first press turns on the

screen backlight. In this case, press

the button a second time to select

the mode. Continue pressing the

Mode button to scroll through the

Pulse, Continuous Flow, or Sleep

modes. When the desired mode

appears in the display, stop pressing

the button and wait. The display

will return to the run time screen

of the mode you selected, and the

device will operate in this mode.

6. Set the flow rate.

To set the device’s flow setting, press

either the + or – button. To increase

the flow setting, press the + button.

To decrease the flow setting, press the

– button. The device can be set to 1,

1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, and 6

in Pulse or Sleep mode. SimplyGo can

be set to 0.5, 1, 1.5, and 2 in Continuous

Flow mode. Always verify the flow rate

when turning on SimplyGo.

To set up and use the mobile cart,

follow these easy steps.

1. Set the mobile cart on a level surface, hold the handle

with one hand, and open the base support.

2. With SimplyGo properly positioned in its carrying case,

place the device on the base of the cart and secure

using the elastic strap on the back of the case.

Mobile cart operation

Oxygen delivery modes

Pulse mode

When SimplyGo is in the Pulse mode, it detects when the user

begins to take a breath and then delivers a pulsed volume of oxygen

determined by the setting number.

Continuous Flow mode

In Continuous Flow mode, a constant flow of oxygen is supplied based

on the setting number (in liters per minute). When the desired mode

appears in the display, stop pressing the button and wait. The display

will return to the run time screen of the mode you selected and the

device will operate in this mode.

Sleep mode

Sleep mode is similar to the Pulse mode; SimplyGo detects when the

user begins to take a breath and then delivers a pulsed volume of

oxygen determined by the setting number. The Sleep mode differs

from Pulse mode in that it has a more sensitive triggering level and

delivers a softer, more comfortable pulse for sleeping. If no breath

is detected for a period of time, the system automatically delivers

a continuous flow of oxygen at a rate consistent with the last used

Continuous Flow mode setting.

3. Press down on the “PUSH” button located at the top

of the handle. Then pull the handle upward to extend

the cart arm to the desired height.

4. Attach the accessory bag around the cart handle using

the bag’s elastic strap.

All rights are reserved.

Philips Healthcare reserves the right to make changes in specifications and/or to

discontinue any product at any time without notice or obligation and will not be

liable for any consequences resulting from the use of this publication.

Hoech WMB 11/21/11 MCI 4104502 PN 1094881

Please visit www.philips.com/simplygo

Respironics and SimplyGo are trademarks of Respironics, Inc. and its affiliates.

Philips Healthcare is part of

Royal Philips Electronics

How to reach us

www.philips.com/healthcare

healthcare@philips.com

Asia

+49 7031 463 2254

Europe, Middle East, Africa

+49 7031 463 2254

Latin America

+55 11 2125 0744

North America

+1 425 487 7000

800 285 5585

(toll free, US only)

Philips Respironics

1010 Murry Ridge Lane

Murrysville, PA 15668

Customer Service

+1 724 387 4000

800 345 6443 (toll free, US only)

Philips Respironics

International Headquarters

+33 1 47 28 30 82

www.philips.com/respironics

Autres manuels pour SimplyGo

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philips Équipement d'oxygène

Philips

Philips EverFlo Q Manuel utilisateur

Philips

Philips SimplyGo Manuel utilisateur

Philips

Philips EverFlo Q Manuel d'utilisation et d'entretien

Philips

Philips EverFlo Manuel utilisateur

Philips

Philips SimplyGo Manuel utilisateur

Philips

Philips simplyFLO Manuel utilisateur

Manuels Équipement d'oxygène populaires d'autres marques

Maxtec

Maxtec MAXO2+A Mode d'emploi

AirSep

AirSep SeQual Workhorse Series Manuel utilisateur

SeQual

SeQual Eclipse 1000 Manuel utilisateur

dideco

dideco KIDS D100 Manuel utilisateur

C-Aire

C-Aire Companion Series Manuel utilisateur

Teledyne

Teledyne 329R Manuel utilisateur

ResMed

ResMed MIRAGE LIBERTY 61848 Manuel utilisateur

SeQual

SeQual Regalia Manuel utilisateur

O2matic

O2matic HOT 100 Manuel utilisateur

wtw

wtw Oxi 330/SET Manuel

C-Aire

C-Aire FreeStyle Comfort Manuel utilisateur

DeVilbiss

DeVilbiss iFILL PD1000A Series Manuel

Inova Labs Inc.

Inova Labs Inc. LifeChoice Manuel utilisateur

Nidek Medical

Nidek Medical OCSI Manuel utilisateur

Point Four Systems

Point Four Systems MBD075 Manuel utilisateur

John Bunn

John Bunn Optium JB0180 Manuel utilisateur

Dräger

Dräger Oxy K 30 E/S Manuel utilisateur

ABB

ABB 9408 Series Manuel utilisateur