Philips ILS-CL-8RES Manuel utilisateur
Lightolier Controls
2828 Trade Center Drive, Suite 130B
Carrollton, TX 75007
+1-800-526-2731 (In the United States and Canada)
214-647-7880
Fax: 214-647-8032
www.lolcontrols.com
Lilghtolier Controls is a hilips Controls brand.
This manual is for informational use only and is subject to change without notice.
Lightolier Controls assumes no responsibility or liability for any claims resulting
from errors or inaccuracies that may appear in this manual.
Version as of: November 18, 2009
Document: 85-6370A0
Lytemode 8-Button Remote Station User’s Guide
©2009 hilips Controls. All Rights Reserved.
THREE YEAR LIMITED WARRANTY
The hilips Controls product, when properly installed and under normal conditions of use
(without overload, abuse or alteration), is warranted to you, the original user, for a period
of three years form the date of original retail purchase, to be free from defects in materials
and workmanship. If during the warranty period you believe the purchased product or any
part thereof has such a defect, you must return the product (or part) at your cost during
such period, with proof of purchase (or if installed by a third-party a written explanation
of installation transaction with proof of date), to hilips Controls, 2828 Trade Center Dr.
Ste. 130B, Carrollton, TX 75007, for repair or replacement (or to an authorized hilips
Controls supplier which agrees in advance to handle the return and replacement by
factory authorization). If the product or part is found by hilips Controls to have been
defective in material or workmanship it will be repaired or replaced (as deemed necessary
by hilips Controls), and the replacement will be returned to you free of charge. The
original user is solely responsible for any costs associated with removal and
re-installation of the product and shipping to hilips Controls or its authorized supplier.
HILI S CONTROLS LIMITS THE DURATION OF THE IM LIED WARRANTY OF
MERCHANTABILITY WITH RES ECT TO THE RODUCT TO THE LIMITED
WARRANTY ERIOD SET FORTH ABOVE, AND OTHERWISE DISCLAIMS ALL
IM LIED WARRANTIES WITH RES ECT TO THE RODUCT AND ITS ARTS.
Some states disallow certain limitations on implied warranties so you should consult your
state law if you have a questions regarding this limitation and disclaimer. hilips Controls
disclaims any and all liability for incidental, consequential, special or indirect damage
arising out of any claimed breach of warranty or otherwise. However, some states do not
allow exclusion or limitation of such damages, so this disclaimer may not apply to you.
The remedy provided in the Limited Warranty for defective products is the user’s sole and
exclusive remedy, subject to your state law. Further, this Warranty gives the user specific
legal rights, and the user may also have other rights which may vary from state to state.
If you believe warranty claim is warranted, you may contact your nearest authorized
hilips Controls supplier. If one does not exist in your area, please contact hilips
Controls Customer Service at the above address (or at 1-800-526-2731), or please visit us
at www.lolcontrols.com.
Room Combine Switch User’s Guide 1
Table of Contents
Customer Service .....................................................................2
Lytemode System Overview ...................................................3
Room Combine Switch Overview ...........................................4
Installation ...............................................................................5
Setting ILS Network ID ...........................................................6
Setup ........................................................................................8
Mode .................................................................................8
ID Address ......................................................................10
LED Intensity .................................................................11
Display Version ..............................................................12
Operation ...............................................................................13
Setting Combine IDs (Method 1) ...................................13
Setting Combine IDs (Method 2) ...................................15
Combine/Un-combine Rooms ........................................16
Factory Defaults and Troubleshooting ..................................17
Resetting Factory Defaults .............................................17
Troubleshooting ..............................................................18
Installing Custom Buttons .....................................................19
Specifications ........................................................................20
Accessories ............................................................................20
2Customer Service
Customer Service
Technical and Sales assistance for Lytemode products are
available worldwide.
Phone: +1-800-526-2731 (In the United States and Canada)
+1-214-647-7880 (Worldwide)
Room Combine Switch User’s Guide 3
Lytemode System Overview
The Lytemode System is designed to control architectural
lighting by distributing both power and intelligence. The system
provides processing power and control at each respective Master or
Remote Station, eliminating the need for a central processor.
Lytemode Master Stations provide individual control for up to 16
channels, 13 scenes plus “Off”, and adjustable fade times. Multiple
Master Stations may be linked together for control of up to 128
Channels and 13 preset scenes. By combining Lytemode Master
Stations with Lytemode Remote Stations, the system provides
remote access to scenes, Master Raise/Lower control, Multi-room
partition control, or Master Station Lockout. Lytemode Master
Stations are easily programmed using the front panel buttons,
without removing the Master Station from the wall, and without the
need for a computer. Lytemode Master Stations are compatible with
both Lightolier Controls Insulated Gate Bipolar Transistor
(IGBT) Dimming Cabinets as well as Silicon Controlled Rectifier
(SCR) Dimming Panels.
Lytemode products are controlled by the Intelligent Lytemode
System (ILS) protocol. All Lytemode control devices must be
connected to the ILS system and given a unique ID (or address) in
order to interact properly. The ID identifies the device on the
network and allows the device to avoid network collisions when
transmitting data.
4Room Combine Switch Overview
Room Combine Switch Overview
The Lytemode Room Combine Switch provides easy partition
control of meeting rooms, banquet halls, and other large partitioned
spaces. When partitions are open, the Room Combine Switch links
the Master Stations in each room so that adjustments to one Master
Station are duplicated on all linked Master Stations, maintaining a
uniform look throughout the expanded space. When partitions are
closed, the Room Combine Switch isolates the Master Stations in
each room for individual room control.
The Room Combine Switch is capable of controlling up to eight
partitions. Three Room Combine Switches may be linked together
for control of up to 24 partitions.
H
C
D
E
F
G
B
ALighting Panel
Room Combine
A
BC
D
E
G
F
North East
West South
PF1 PF2
Room Combine Switch User’s Guide 5
Installation
The Lytemode ILS Network consists of a single CAT5e cable
connecting all ILS modules in a daisy chain manner. All units
connect to the network using a 9-pin connector (included).
To install:
Step 1. Unpack unit and inspect for any signs of shipping damage.
Ensure that two mounting screws are included.
Step 2. Connect ILS Network Cable to 9-pin connector at back of
Room Combine Switch.
Step 3. Insert Combine Switch into standard deep rough-in box
(not included). Secure with two supplied mounting screws.
Step 4. Snap faceplate into place.
1WH/OR(+Data)
2 OR (- Data)
3SHIELD
4WH/GN(+Volts)
5 GN (Ground)
6WH/BL(+Volts)
7 BL (Ground)
8WH/BR(+Volts)
9 BR (Ground)
9-Pin Connector Wiring
PIN SIGNAL
9-Pin
Faceplate
Connector
Room
Combine
Switch
Rough-In Box
(not included)
6Setting ILS Network ID
Setting ILS Network ID
Lytemode products are controlled by the Intelligent Lytemode
System (ILS) protocol. All Lytemode ILS devices must be given an
ID (or address), which identifies the device on the network and
allows it to avoid network collisions when transmitting data.
Standard IDs are in the range of 1 to 255. An ID of 0 will disable
the unit and prevent it from transmitting on the network.
IDs are typically unique. For example, an ILS Master will require a
unique ID to allow dimmers to track its channel levels. However,
ILS Remotes should be given the same ID as the ILS Master it
controls. ILS Remotes rely on the fact that they are manually
triggered to avoid network collisions with other ILS Remotes
having the same ID.
The table on the following page provides guidelines for addressing.
Room Combine Switch User’s Guide 7
ILS Network Addressing:
* Notes:
1 – Matches ILS Master ID.
2 – ILS Masters must be programmed to accept.
3 – Will respond to Remote Polls, Status Requests and Commands.
4 – Unit uses a self generated ID.
Note: Refer to the instructions included with your particular
device(s) in order to set corresponding control IDs.
Device ID Sub-ID Devices / ID Remotely
Polled? Notes *
Remote 1-255 0 Multiple No 1
Two Button
Remote Auto 0 n/a No 4
Global Remote 1-255 0 Multiple No 2
Remote Keypad 1-255 0-7 1 Yes 3
Remote I/O 1-255 0-7 1 Yes 3
Room Combine 1-255 0 1 Yes 3
Mini-Master 1-255 0-7 1 Yes 3
Master 1-255 0-7 1 Yes 3
RS-232 Port Auto 0 n/a No 4
Smart Matrix
Dimmer Rack 1-255 n/a 1 Yes 3
Capio Dimmer
Rack 1 -255 n/a 1 Yes 3
8Setup
Setup
This section describes how to program the unit’s Mode, Address,
LED Brightness, and display the unit’s Version.
Mode
The unit can be set to function in one of several Modes as follows:
Step 1. Press and hold D and E for 3 seconds.
ALED will blink rapidly.
Step 2. Enter Mode by setting Gand Hbuttons as
either Off or On as shown in the following
table. (LEDs will blink for any Mode not
supported.)
Step 3. Press Ato save and exit.
Mode G H
0 – RCGP Remote (1-8) Off Off
1 – RCGP Remote (9-16) Off On
2 – RCGP Remote (17-24) On Off
3 – RCGP Master On On
H
C
D
E
F
G
B
A
H
C
D
E
F
G
B
A
C
D
B
A
Example:
Mode 3
Table des matières
Autres manuels Philips Équipement d'éclairage
Philips
Philips B50 Manuel utilisateur
Philips
Philips Hue 1822511 Manuel utilisateur
Philips
Philips goLITE BLU Manuel utilisateur
Philips
Philips MASTER Colour CDM-R111 Manuel utilisateur
Philips
Philips HP8550 Manuel utilisateur
Philips
Philips Lightstrip Plus 71901/U8 Series Manuel utilisateur
Philips
Philips eW Cove QLX Powercore Manuel utilisateur
Philips
Philips HF3670 Manuel utilisateur
Philips
Philips 17274/**/16 Manuel utilisateur
Philips
Philips Selecon Accent LED Beamshaper Manuel utilisateur
Philips
Philips PLFRESNEL1 Manuel utilisateur
Philips
Philips B50ST Manuel utilisateur
Philips
Philips Ligholier KUBIK 1.0 SL110A Manuel utilisateur
Philips
Philips hue Lightstrip Plus Manuel utilisateur
Philips
Philips Compac CTX6 Series Manuel utilisateur
Philips
Philips burton SUPER EXAM 50 LED Fiche technique
Philips
Philips SL PAR 150 Manuel utilisateur
Philips
Philips ColorGraze IntelliHue Powercore BCS559 30x60 RGBMW... Manuel utilisateur
Philips
Philips Ecomoods 57940/31/96 Manuel utilisateur
Philips
Philips ColorDial Pro Manuel utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
