Philips EH313L Manuel utilisateur

PHILIPS EH313L

7.5W x 2 LED FLOODLIGHT

LED Light

Lampshade

Wall Box

PIR (Motion Sensor)

INTRODUCTION

This 7.5W x 2 LED FLOODLIGHT is a unique indoor or

outdoor lighting system for your home or business place:

1. Prior to normal operation, test the light no matter in

the daytime or nighttime.

2. Determine how long the light will be on after motion

is detected.

3. Manual override feature enables the light to stay on

continuously both day and night.

4. Two adjustable lights allow you to provide the

optimum lighting coverage.

Note: Read this entire manual before you start to

install the system.

SAFETY PRECAUTIONS

DO NOT install this fitting when it is raining.

DO isolate the power supply during installation or

maintenance.

DO ensure that the power supply circuit is protected

by a 16 amp circuit breaker or suitable equivalent

fuse.

The fixing screw should not be removed after

installation. Secure the connection of the light

head assembly and motion sensor to the base, so

as to avoid any unsteadiness.

The unit can be installed vertically, not horizontally

as shown in the below drawing. (FIGURE 1)

Wall Mount Recommended (FIGURE 1)

IMPORTANT

Installation must be performed by skilled technicians

who are informed about the standards and technical

requirements of the appliance and its proper

installation.

Check your local codes as they apply to your situation.

If the house wiring is of aluminum, consult with an

electrician about proper wiring methods.

Before proceeding with the installation, TURN OFF

THE POWER TO THE LIGHTING CIRCUIT AT THE

CIRCUIT BREAKER OR FUSE BOX TO AVOID

ELECTRICAL SHOCK.

CHOOSING A MOUNTING LOCATION

For safety and the best results, fix the unit on a solid

wall, 2.5m above the ground.

For outdoor installation, a location under eaves is

preferable.

Avoid aiming the motion sensor at pools, heating

vents, air conditioners or objects which may change

temperature rapidly.

Do not allow sunlight to fall directly on the front of

unit.

Try to avoid pointing the unit at trees or shrubs or

where the motion of pets may be detected.

The motion sensor is more sensitive to objects

moving across its field of view. It is less sensitive

to objects moving directly towards the sensor head.

(FIGURE 2)

FIGURE 2









INSTALLATION

A drill and a screwdriver are needed for installation.

Select a location for the unit based on the coverage

angles shown in FIGURE 3.

180°

12m

110°

UNIT(m)

COVERAGE ANGLES

FIGURE 3

WIRING INSTRUCTION

(1) Switch off the power source.

(2) Detach the wall box by unscrewing the screw

adjacent to the control knobs (retain the screw for

later use). (FIGURE 4)

FIGURE 4

(3) Use a screwdriver to break a small hole on the cable

gasket, enabling the power cord to enter the wall

box.

(4) Route the power cord through the cable gasket.

(5) Determine the proper location to mount the light.

Use the wall box as a template to mark the fixing

holes on the wall. Drill the holes and insert the

plastic wall plugs supplied. Fix the wall box using

two screws provided. (FIGURE 5)

38 m

FIGURE 5

(6) Strip approximately 6-8mm insulating part of the

wires from the power cord.

(7) Connect the BROWN wire (Live wire) to the terminal

block “L” mark.

Connect the BLUE wire (Neutral wire) to the

terminal block “N” mark. (FIGURE 6)

TO LAMP LIVE

NEUTRAL

AC POWER

BROWN

BLUE

FIGURE 6

(8) Replace the unit to the wall box by fastening the

screw retained.

ADJUST ANGLE

The lights can be adjusted up to 45° leftward and

rightward respectively; the PIR sensor can be adjusted

90°leftward and 90°rightward. (FIGURE 7a)

RIGHT 45°

LEFT 45°

RIGHT 90°

LEFT 90°

FIGURE 7a

The lights can be adjusted 37.5° downward. For the

PIR sensor, on the rear side of motion sensor is an

adjustment bar which can be used to adjust the angle of

PIR sensor to up to 30°downward. (FIGURE 7b)

30°

37.5°

adjustment

FIGURE 7b

SETTING THE LIGHTING SYSTEM

(1) TEST MODE

Turn the LUX control and the TIME control

counterclockwise to the edge –the TEST position.

(FIGURE 8)

Time

5S 12min

Lux

FIGURE 8

Turn on the wall switch. The unit will start warming

up for about 60 seconds. After warm-up it will

automatically revert to normal operation. During the

warm-up period the lights will stay on.

Walk through the detection area. The lights turn on

when you move and turn off when you stop. Wait

until the lights turn off and then move again to test

the sensor.

Adjust the motion sensor to cover the desired

detection area. For a smaller coverage area, point

the sensor down; for a larger coverage area, point

the sensor up.

(2) TIME ADJUSTMENT

The TIME adjustment controls how long the light will stay

on after motion has been detected.

Turn the TIME control knob clockwise to increase (up to

12 minutes) the period the lights stay on or counter

clockwise to decrease (down to 5 seconds) the time

delay (FIGURE 9).

Time

5S 12min

Time

5S 12min

FIGURE 9

(3) LUX ADJUSTMENT

The LUX control knob determines at which ambient Lux

level the lights will turn on when the sensor is in

Automatic Operation mode.

The adjustable Lux range is between 30 and 200 Lux.

Turn the LUX control knob clockwise to the MOON

position and the lights will only turn on at night (below 30

Lux). Turn the LUX control knob counterclockwise to

increase the Lux setting. Adjust the control knob

depending on your requirements.

Lux

FIGURE 10

OPERATION

Depending on your needs, you can switch the unit

between the following operation modes: Automatic

Operation and Manual Override.

(1) Automatic Operation

Turn on the wall switch. After about 60 seconds

warm-up the sensor will enter Automatic Operation.

When the sensor detects motion and the ambient light

level is lower than the LUX setting, the lights will

automatically turn on. The lights will stay on for the

duration of TIME setting and then turn off. Note that if

motion is detected again while the lights are still on, the

time counting will be reset.

Adjustment

Bar

(2) Manual Override

To keep the lights on regardless of the motion, you can

override the automatic operation. To enable Manual

Override mode, first ensure that the lights are on and

then turn the wall switch off and on twice (off-on, off-on)

within 3 seconds. The interval between the first and

second operation must be within 0.5 - 2 seconds.

In Manual Override mode, the lights will remain on for

around 5 hours. After 5 hours the lights will turn off and

the motion sensor will revert to Automatic Operation.

Users can also manually set the motion sensor back to

Automatic Operation by: 1) turning the wall switch off and

on twice within 3 seconds; or 2) turning off the wall switch

for at least 10 seconds and then turning it back on.

TROUBLESHOOTING

Light does not turn on

Confirm that you have made a correct “wiring

connection”.

Ensure that the load is within normal range.

Change the load if necessary.

Adjust the LUX control knob by turning it

counterclockwise.

Light remains on

Make sure the wiring connection is correct.

Adjust the TIME control knob by turning it

counterclockwise.

Make sure that the unit is not in Manual Override

mode.

Others

The specification of protective shield shall consult

to local service agent.

SPECIFICATIONS

Power Requirement

AC 220 - 240V / 50Hz

Lighting Load

15W (7.5W x 2)

Color Temperature (K)

5000K

CRI

>75

Lumen (lm)

800lm (400lm x 2)

L70 Life Span (hours)

30000 hr

Detection Angle

Up to 180°at 2m Height

Detection Range

Up to 12m (39.4ft) at 2m

Height

Projection Area

7m2

Sensor Swiveling Angle

Up to 90°Leftward

Up to 90°Rightward

Up to 30°Downward

Light Adjustable Angle

Up to 45o Leftward

Up to 45°Rightward

Up to 37.5°Downward

Mounting Height

Recommended 2.5m (8.2ft)

Wall Mount

Time Adjustment

5 seconds - 12 minutes

Lux Adjustment

30 - 200 Lux

Operation Mode

Off/Auto/Manual override

Warm Up Time

About 60 seconds

Working Temperature

-20°C - +40°C

Dimension

201 x 185 x 167(mm)

Weight

796±10g

Protection Class

Class II

Protection Degree

IP44

Safety

*Specifications are subject to change without notice.

A501112090R

Warning:

Do not dispose of electrical appliances as unsorted

municipal waste, use separate collection facilities.

Contact your local government for information regarding

the collection systems available.

If electrical appliances are disposed of in landfills or

dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your

health and well-being.

Autres manuels Philips Projecteur

Philips

Philips SL WASH 180 RGBW Mode d’emploi

Philips

Philips BVP500 Guide de l'utilisateur

Philips

Philips GearUnits ECM 330 Manuel utilisateur

Philips

Philips SL ParBlazer 100 UV Mode d’emploi

Philips

Philips BVP483 Manuel utilisateur

Philips

Philips conTempo RVP150 Manuel utilisateur

Philips

Philips HADCO WAMT14 Manuel utilisateur

Philips

Philips P-5557-B Manuel utilisateur

Philips

Philips VL500 Wash Luminaires Manuel utilisateur

Philips

Philips F Series Manuel utilisateur

Philips

Philips Clearflood Large BVP651 Manuel utilisateur

Philips

Philips SmartBright BVP173 Manuel utilisateur

Philips

Philips SmartBright BVP171 Manuel utilisateur

Philips

Philips PentaFlood Manuel utilisateur

Philips

Philips BVP154 Series Manuel utilisateur

Philips

Philips P-2558-C Manuel utilisateur

Philips

Philips HNF901 Guide de l'utilisateur

Philips

Philips eXpanium eXp 401 Manuel utilisateur

Philips

Philips MVF 406, 1800 W cat A1 Guide de démarrage rapide

Philips

Philips BVP510 Guide de l'utilisateur

Philips

Philips Tempo Flood Light Manuel utilisateur

Philips

Philips VARI-Lite VL4000 Manuel utilisateur

Philips

Philips BVP158 Manuel utilisateur

Philips

Philips BVP158 LED24/WW NW CW PSU 20W SWB CN Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur