Philips DS9000 Manuel utilisateur
Installation Guide
DS-9000 / DS-9100 Series DVR (V1.0.2)
Installation Guide - DS-9000 / DS-9100 Series DVR 1
Verify Contents
Verify that the package contents are correct by checking the
items against the packing list.
Note: Please contact your dealer for damaged or missing
items.
DVR Pre-Installation
The DS-9000 and DS-9100 Series DVRs are highly advanced
surveillance equipment that should be installed with care.
Please take into consideration the following precautionary
steps before installation of the DVR.
1. Keep all liquids away from the DVR.
2. Install the DVR in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory
specifications.
4. Install a manufacturer recommended HDD.
DVR Installation
During the installation of the DVR:
1. Use brackets for rack mounting.
2. Ensure there is ample room for audio and video cables.
3. When installing cables, ensure that the bend radius of the
cables are no less than five times than it’s’ diameter.
4. Connect both the alarm and RS-485 cable.
5. Allow at least 2cm (~0.75in) of space between racks
mounted devices.
6. Ensure the DVR is grounded.
7. Environmental temperature should be within the range of
-10ºC ~ 55ºC, 14ºF ~ 131ºF.
8. Environmental humidity should be within the range of
10% ~ 90%.
Hard Disk Installation
Before installing a hard disk drive (HDD), please make sure
the power is disconnected from the DVR. A factory
recommended HDD should be used for this installation.
Tools Required: Phillips screwdriver.
To install a HDD on your
DVR:
1. Remove the lid of the
DVR by unfastening
the screws on the back.
2. Install the HDD in the
HDD rack using the
pro- vided screws. To
install on the bottom
HDD rack, the top
HDD rack must be
removed first.
3. Connect the HDD to
the motherboard of the
DVR with the included
data cable.
4. Connect the power
cable to the HDD.
5. Re-install the lid of the
DVR and fasten
screws.
2 Installation Guide - DS-9000 / DS-9100 Series DVR
Rear Panel Diagram
No. Item Description
1 VIDEO IN BNC connectors for analog video input.
AUDIO IN BNC connectors for analog audio input.
2 VIDEO SPOT OUT BNC connector for monitor. If VGA is connected, it is for video output only. If VGA
is not connected, it is for video output, playback and showing PTZ controls.
AUDIO SPOT OUT BNC connector for audio output. If VGA is connected, audio is synchronized with
VGA. If VGA is not connected, audio is synchronized with VIDEO SPOT OUT.
3 VIDEO OUT BNC connector for video output. If VGA is connected, it is used for spot output only
with local video display, playback, recording and PTZ controls. If VGA is not
connected, it is used as the main video output with local video display and menu
operations.
AUDIO OUT BNC connector for audio output. This connector is synchronized with VIDEO OUT.
4 LINE IN BNC connector for audio input.
5 VGA DB9 connector for VGA output. Display local video output and menu.
6 Loop Out (Optional) DB15 interface for connection video matrix and monitor.
7 RS-232 Interface Connector for RS-232 devices.
8 eSATA (Optional) Connects external SATA HDD, CD/DVD-RM or disk array.
9 LAN Interface Connector for LAN (Local Area Network).
10 USB Interface Connector for USB devices.
11 Termination Switch RS-485 termination switch.
Up position is not terminated. Down is 120Ω termination.
12 RS-485 Interface Connector for RS-485 devices. T+, T- pin connects to PTZ.
Controller Port D+, D- pin connects to Ta, Tb pin of controller. For cascading devices, the first
DVR’s D+, D- pin should be connected with the D+, D- pin of the next DVR.
ALARM IN Connector for alarm input (up to 16 channels).
ALARM OUT Connector for alarm output (4 channels).
13 GROUND Ground(needs to be connected when DVR startup)
14 POWER AC 110V ~ 220V
Installation Guide - DS-9000 / DS-9100 Series DVR 3
Peripheral Connections
Connecting to Alarm Input / Output Device
The alarm input/output interface of the DVR is shown below:
The alarm input is an open/close relay. If the input is not an
open/closed relay, follow the connection diagram below:
To connect to an AC/DC load, use the following diagram:
For DC load, JP4 can be used within the limit of 12V/1A
safely. If the interface is connected to an AC load, JP4 should
be left open. Use an external relay for safety (as shown in the
figure above).
There are 4 jumpers (JP4, JP5, JP6, and JP7) on the
motherboard, each corresponding with one alarm output. By
default, jumpers are connected. To connect an AC load,
jumpers should be removed.
Note: An external relay is needed to prevent electric shock
when connecting to an AC load.
Alarm Connection
To connect alarm devices to the DVR:
1. Disconnect pluggable block from the ALAM IN /ALARM
OUT terminal block.
2. Unfasten stop screws from the pluggable block, insert
signal cables into slots and fasten stop screws. Ensure
signal cables are in tight.
3. Connect pluggable block back into terminal block.
RS-485 Connection
To connect RS-485 devices to the DVR:
1. Disconnect pluggable block from the RS-485 terminal
block.
2. Unfasten stop screws from the pluggable block, insert
signal cables into slots and fasten stop screws. Ensure
signal cables are in tight.
3. Connect pluggable block back into terminal block.
4 Installation Guide - DS-9000 / DS-9100 Series DVR
Note: The RS-485 PTZ control should be connected with
the
T+ and T- pin on the RS-485 terminal block.
Controller Connection
To connect a controller to the DVR:
1. Disconnect pluggable block from the KB terminal block.
2. Unfasten stop screws from the KB D+, D- pluggable
block, insert signal cables into slots and fasten stop
screws. Ensure signal cables are in tight.
3. Connect Ta on controller to D+ on terminal block and Tb
on controller to D- on terminal block. Fasten stop screws.
4. Connect pluggable block back into terminal block.
Note: Make sure both the controller and DVR are grounded.
HDD Storage Calculation
Chart
The following chart shows an estimation of storage space
used based on recording at one channel for an hour at a fixed
bit rate.
Bit Rate Storage Used
96K 42M
128K 56M
160K 70M
192K 83M
224K 98M
256K 112M
320K 140M
384K 168M
448K 196M
512K 225M
640K 281M
768K 337M
896K 393M
1024K 450M
1280K 562M
1536K 675M
1792K 787M
2048K 900M
Note: Please note that supplied values for storage space
used is just for reference. Storage space used is estimated by
formulas and may have some deviation from actual value.
Autres manuels pour DS9000
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Philips DVR
Philips
Philips DVDR615 Manuel utilisateur
Philips
Philips VR140/58 Manuel utilisateur
Philips
Philips DVDR3305/02 Manuel utilisateur
Philips
Philips Cineos DVDR9000H Manuel utilisateur
Philips
Philips DVR2008/97 Manuel utilisateur
Philips
Philips VR330/07 Manuel utilisateur
Philips
Philips DVDR3305/02 Manuel utilisateur
Philips
Philips 34DV2 Manuel de service
Philips
Philips TL24A5T Manuel utilisateur
Philips
Philips DVR2008 Manuel utilisateur
Philips
Philips VR 540 Manuel utilisateur
Philips
Philips VR558 Manuel utilisateur
Philips
Philips DSR6000 Guide de démarrage rapide
Philips
Philips HDR5750 Manuel utilisateur
Philips
Philips DSR7000 Manuel utilisateur
Philips
Philips DVR1EP08 Manuel utilisateur
Philips
Philips VR 700 Manuel utilisateur
Philips
Philips DVDR730/0x Manuel utilisateur
Philips
Philips Divar Manuel utilisateur
Philips
Philips VAE8015 Manuel utilisateur
