Philio Technology Corporation PAN34 Manuel utilisateur

Specification

Operating Voltage 100 -240VAC 50-60Hz

Maximum Load Re i tive load 5A max.

Range Minimum 40m indoor 100m outdoor line of ight

Operating Temperature 0°C - 40°C

Humidity Up to 85% max.

Storage Temperature -20°C to 60°C

Location Indoor u e only

Frequency Range 868.40MHz; 869.85MHz (EU)

908.40MHz; 916.00MHz (USA/Canada)

920.90 MHz, 921.70 MHz, 923.10 MHz (Taiwan)

RF Maximum Power +10dBm (Peak), -10dBm (Average)

OTA Support

FCC ID RHHPAN34

Dimen ion 47.5 x 39 x16 mm

Wire 0.75mm² , 18AWG

** Specification are ubject to change and improvement without notice.

Troubleshooting

Symptom Cause of Failure Recommendation

The PAN34 not working

and LED off

1. The PAN34 i not

connect to the Main

power

2. The PAN34 break

down

1. Check power connection

2. Don’t open up the PAN34 and

end it for repair.

The hutter move direction

i rever e

Wrong connection of NC

and NO to the motor

Swap the NC NO connection

PAN34 LED light work fine

But can not control

1. No a ociation etting

2. Same frequency

interference

3. S1 or S2 are both

pre ed in Two Pu h

Button witch type,

PAN34 would not accept

RF command.

1. Carry out a ociation

2. Wait for a while to re-try

3. Relea e S1 and S2

Fig 1. Assembling Installation and wiring

1. Put the in wall PAN34 into a wall box and connect the AC power wire L,N to PAN34

connector L, N.

2. Connect the wall witch to the PAN34 a Fig1.

3. To manually witch up and down of the hutter, imply pre the external witch S1 or S2.

The detail i de cribed in 5-2.

4. PAN34 built in meter function and can read the Watt, KWh, V(Voltage), I(Current), PF

(Power Factor) of the load by u ing Z-Wave command cla , u er can et a thre hold

current to get the warning cau ed by abnormal operation

5. PAN34 have overload protection function and can help to prevent hort circuit cau ed by

load.

For Instruction to http: www.philio-tech.com

DANGER

Danger of electrocution!

All work on the device may be performed only by a qualified and licen ed electrician. Ob erve

national regulation .

Any work introducing change into the configuration mu t be alway performed with

di connected voltage.

Choosing a Suitable Location

1. Do not locate the Module facing direct unlight, humid or du ty place.

2. The uitable ambient temperature for the Module i 0°C~40°C.

3. Do not locate the Module where exi t combu tible ub tance or any ource of heat, e.g.

fire , radiator , boiler etc.

4. After putting it into u e, the body of Module will become a little bit hot of which phenomenon

i normal.

Adding to Z-Wave

Network

In the front ca ing, there i an include button with LED indicator below which i u ed

to carry out inclu ion, exclu ion, re et.

The table below li t an operation ummary of ba ic Z-Wave function . Plea e refer

to the in truction for your Z-Wave

Certificated Primary Controller to acce the

Setup function, and to include/exclude/re et device .

Function Description LED Indication

No node ID The Z-Wave Controller doe not allocate

a node ID to the PAN34.

LED 2- econd on, 2-

econd off

Add

(Cla ic

Inclu ion)

1. Put your Z-Wave controller into

inclu ion mode by following the

in truction provided by the

controller manufacturer.

One pre one fla h LED

 To upport handling of

the device when already

in talled the external

witch can be u ed for

inclu ion or exclu ion for 3

minute after power up.

2. Pre ing Include button three time

within 2 econd will enter inclu ion

mode.

SmartStart 1. The product ha a DSK tring. Key

in the fir t five digit to initiate the

SmartStart proce , or can QR

code.

Ex: DSK: 18112-24021- 48001-

62259-57092-27453-08187-47408

SmartStart

enabled product can

be added into a Z-Wave™ network

by canning the Z-Wave™ QR

Code on the product, with a

controller providing SmartStart

inclu ion. No further action i

required and the SmartStart product

will be added automatically to the

clo e t network within 10 minute of

being witched on.

Notice:

The QR Code can be found on the

device PAN34 or in the box.

Remove

(Exclu ion)

1. Put your Z-Wave controller into

exclu ion mode by following the

in truction provided by the

controller manufacturer.

One pre one fla h LED

 To upport handling of

the device when already

in talled the external

witch can be u ed for

inclu ion or exclu ion for 3

minute after power up.

2. Pre ing Include button three

time within 2 econd will enter

exclu ion mode.

Node ID ha been excluded. LED 2 On, 2 Off (No

node ID)

Re et 1. Pre ing Include button three time

within 2 econd will enter inclu ion

U e thi procedure only in

the event that the primary

mode. controller i lo t or

otherwi e inoperable.

2. Within 1 econd, pre Include

button again for 5 econd .

3. ID are excluded. LED 2 On, 2 Off (No

node ID)



Adding a node ID allocated by Z-Wave Controller mean inclu ion. Removing a node ID

allocated by Z-Wave Controller mean exclu ion.



Failed or ucce in including/excluding the node ID can be viewed from the Z-Wave

Controller.

Sometime people are not ea y to execute exclu ion or inclu ion e pecially when PAN34

already in talled in a wall box. To olve thi i ue, PAN34 upport a pecial feature that can

u e S1 or S2 to execute “exclu ion, inclu ion, Re et or A ociation” at the fir t 3 minute

when fir t time connect to main power.

LED Indication

There i a LED for identify function in the front ca e. PAN34 upport the indicator ID

0x50 (Identify) and Propertie ID 0x03, 0x04 and 0x05.

To di tingui h what mode the PAN34 i in, view from the LED for identification.

State Type LED Indication

Motor

activate

No matter up or down, clo e or open, Led will fla h every econd

while Motor activate.

When S1 or S2 clo e to L, the LED will fla h even when the motor

top by it elf, thi i to let u er know the S1 or S2 till clo e and

not been relea e yet.

No node ID Under normal operation, when the PAN34 ha not been allocated

a node ID, the LED fla he on and off alternately at 2- econd

interval . By pre ing S1 S2 or Include button, it will top fla hing

temporarily.

Learning When PAN34 i in learning mode, LED fla he on and off

alternately and repeatedly at 0.5 econd interval .

Overload When overload tate occur , the PAN34 i di abled and LED

fla he on and off alternately at 0.2 econd interval . PAN34 will

end Notification type=8, Notification State=0x08 to Group1,

Overload tate can be cleared by di connect and reconnect the

PAN34 to the main power

Moving Range Calibration

1. It i important to carry out a hutter calibration proce before you control the

hutter to move. Pre inclu ion button over 3 econd and relea e before the 6th

econd, the roller hutter controller will tart the hutter calibration proce . The

proce i compo ed of three continue tage . The hutter move to the TOP in fir t

tage, and move to the BOTTOM in econd tage, and move to the TOP again in

third tage. Then PAN34 will know the total range from the BOTTOM to the TOP.

2. During the hutter calibration proce , any emergencie happen you can pre

and relea e the include button to top the proce .

3. If u er found the direction i rever e, thi may cau e by the wrong connection of

NC and NO to the motor, plea e exchange NC and NO connection and execute

calibration proce again.

4. For afe i ue, plea e elect the motor which can top by it elf when go to bottom

end or top end.

Programming

1. Basic Command Class

The PAN34 will re pond to BASIC and BINARY command that are part of the

Z-Wave y tem.

1.1 BASIC_GET

When PAN34 receive Ba ic Get Command, it will end Ba ic Report Command

to report the po ition of the hutter. When the report value i 0x00, that mean the

hutter i at the Bottom, if the report value i 0x63 that mean the hutter i at the

Top, any other value between 0x01~0x62 imply Shutter at the po ition between

top and bottom.

Ba ic Get Command: [Command Class Basic, Basic Get]

Ba ic Report Command：

[Command Class Basic, Basic Report, Value = 0x00 (BOTTOM)]

[Command Class Basic, Basic Report, Value = 0x01~0x62 (Between BOT-

TOM and TOP)]

[Command Class Basic, Basic Report, Value = 0x63 (TOP)]

1-2 BASIC_SET

PAN34 can accept Ba ic Set Command which value i either (0x00) Bottom or

Top (0x63) or (0x01-0x62) the po ition between TOP and Bottom. Other value

(0x64-0xFE) i not acceptable.

[Command Class Basic, Basic Set, Value = 0x63] control the shutter to

the top (0x63)

[Command Class Basic, Basic Set, Value = 0x00(0)] control the shutter to

the bottom(0x00)

[Command Class Basic, Basic Set, Value = 0xFF] control the shutter to

the most recent (non-zero) level.

[Command Class Basic, Basic Set, Value = 0x01-0x62] control the shutter

to the position between bottom and top

2. Multilevel Switch Command Class (Version 3)：

：：

：

2-1 MULTILEVEL SWITCH SET:

PAN34 can accept Multilevel Switch Set Command which value i either (0x00) Bot-

tom or Top (0x63) or (0x01-0x62) the po ition between TOP and Bottom. Other value

(0x64-0xFE) i not acceptable.

[Command Class Multilevel Switch, Multilevel Switch Set, Value = 0x63]

control the hutter to the top (0x63)

[Command Class Multilevel Switch, Multilevel Switch Set, Value =

0x00(0)] control the hutter to the bottom(0x00)

[Command Class Multilevel Switch, Multilevel Switch Set, Value =

0xFF(255)] control the hutter to the the most recent (non-zero) level.

[Command Class Multilevel Switch, Multilevel Switch Set, Value = 0x01-

0x62] control the hutter to the po ition between Bottom and Top.

2-2 MULTILEVEL SWITCH GET

When PAN34 receive Multilevel Switch Get Command, it will end Multilevel Switch

Report Command to report the po ition of the hutter. When the report value i 0x00,

that mean the hutter i at the Bottom, if the report value i 0x63 that mean the hut-

ter i at the top, any other value between 0x01~0x62 imply hutter at the po ition be-

tween top and bottom.

Switch Multilevel Get Command：

[Command Class Multilevel Switch, Multilevel Switch Get]

Multilevel Switch Report Command：

[Command Class Multilevel Switch, Multilevel Switch Report,

Value = 0x00(BOTTOM)]

[Command Class Multilevel Switch, Multilevel Switch Report,

Value = 0x01~0x62(Between BOTTOM and TOP)]

[Command Class Multilevel Switch, Multilevel Switch Report,

Value = 0x63 (TOP)]

2-3 MULTILEVEL SWITCH START LEVEL CHANGE:

Thi i the command which u er can move the hutter up to the top or down to the

bottom.

[Command Class Multilevel Switch, Multilevel Switch Start Level Change,

Up Down Value]

2-3.1 Up Down Bit:

If Up/Down Bit=0x00 Shutter move up

If Up/Down Bit=0x01 Shutter move down

If Up/Down Bit=0x03 no move

[Command Class Multilevel Switch, Multilevel Switch Start Level

Change, Up Down=0x00] control the shutter to the top (0x63)

[Command Class Multilevel Switch, Multilevel Switch Start Level

Change, Up Down=0x01] control the shutter to the bottom (0x00)

[Command Class Multilevel Switch, Multilevel Switch Start Level

Change, Up Down=0x03] Don't move the shutter or stop the moving

shutter

ATT. 1. Ignore Start Level、

Start Level、

Dimming Duration、

Inc/Dec、

Step ize can

not be u ed.

PAN34 can not control the speed of motor.

3. It may have ome di tance error cau ed by motor tart up time.

4. If u er found the error become ignificant, you may u ing S1 or S2 move

hutter to the end or remote move hutter to 0% and 100%, and that will

automatically calibrate thi error.

2-3.4 MULTILEVEL SWITCH STOP LEVEL CHANGE:

When receive Multilevel Switch Stop Level change Command PAN34 will top the

motor.

Z-wave’s Groups introduction (Maximum 5 node )

There i only one group called Lifeline，there i only 5 node for Group1 which up-

port MULTILEVEL_SWITCH_REPORT、METER_REPORT_COMMAND_V3、

ALARM_REPORT and DEVICE_RESET_LOCALLY_NOTIFICATION.

3-1 Device reset locally notification :

When PAN34 i re et manually, it will end a DEVICE_RESET_LOCALLY_

NOTIFICATION to the node of group 1.

3-2 Report the shutter position ：

：：

：

Every time when u er pre S1 or S2 and let hutter to move, PAN34 will report the

po ition tatu to controller, and at the moving proce when change over 10%

PAN34 will end Multilevel Switch Report to Group 1 a well.

Multilevel Switch Report：

Ex. Report po ition at 30%

[Command Cla Multilevel Switch， Multilevel Switch Report，Value = 30(%)]

3-3 Meter Command Class：

：：

：

The Switch will report it (1) in tant Power Con umption (Watt) or (2) accumulated

power con umption(KWH) or (3)

AC load Voltage (V) or (4)

AC load current ( I ) (5)

load power factor (PF) to Z-Wave Controller after receive the Meter Get Command

from Z-Wave Controller.

When the power con umption of load vary over 5%, it will end Meter report to the

node of Group a well

3-3.1 Instant Power Consumption (Watt) of Switch

When receiving Meter Get Command, it will report Meter Report Command to the

node a ked.

Meter Get Command: [Command Class Meter, Meter Get, Scale

=0x02(W)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter

Type = 0x01，Precision = 1，Scale = 0x02，Size = 4，Meter

Value(W) ]

Example:

Meter Value 1 = 0x00 (W)

Meter Value 2 = 0x00 (W)

Meter Value 3 = 0x03 (W)

Meter Value 4 = 0xEA (W)

Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W

3-3.2 Accumulated Power Consumption (KW h)

When receiving Meter Get Command, it will report Meter Report Command to

the node a ked.

Meter Get Command: [Command Class Meter, Meter Get, Scale = 0x00

(KW h)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01， Meter

Type = 0x01， Precision = 2，Scale = 0x00，Size = 4，Meter Value

(KWh)]

Example:

Scale = 0x00 (KWh)

Preci ion = 2

Size = 4 Byte (KW/h)

Meter Value 1 = 0x00(KWh)

Meter Value 2 = 0x01(KWh)

Meter Value 3 = 0x38(KWh)

Meter Value 4 = 0xA3(KWh)

Accumulated power con umption (KW/h) = (Meter Value 2*65536) + (Meter Value

3*256) + (Meter Value 4) = 800.35 (KW/h)

3-3.3 AC load Voltage (V)

When receiving Meter Get Command, it will report Meter Report Command to the

node a ked.

Meter Get Command: [Command Class Meter, Meter Get, Scale

=0x04(V)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter

Type = 0x01，Precision = 1，Scale = 0x04，Size = 2， Meter Value(V)]

Example:

Scale = 0x04 (V)

Preci ion = 1

Size = 2 (2 Byte of V)

Meter Value 1 = 0x09(V)

Meter Value 2 = 0x01(V)

AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)

3-3.4 AC load current ( I

I )

When receiving Meter Get Command, it will report Meter Report Command to the

node a ked.

Meter Get Command: [Command Class Meter, Meter Get, Scale =

0x05(I

I)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter

Type = 0x01，Precision = 2，Scale = 0x05，Size = 2，Meter Value(I

I)]

Example:

Scale = 0x05 (I)

Preci ion = 2

Size = 2 (2 Byte of I)

Meter Value 1 = 0x01(I)

Meter Value 2 = 0x21(I)

AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)

3-3.5 load power factor (PF)

When receiving Meter Get Command, it will report Meter Report Command to the

node a ked.

Meter Get Command: [Command Class Meter, Meter Get, Scale =

0x06(PF)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type

= 0x01， Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter

Value(PF)]

Example:

Scale = 0x06 (PF)

Preci ion = 2

Size = 1 (1 Byte of PF)

Meter Value 1 = 0x63(PF) (It mean that the load power factor i 0.99)

3-3.6 Reset Accumulated Power Consumption (KWh)

Whenever re- tart counting the accumulated power con umption i needed, you can

u e Meter Re et Command to clear it.

Meter Re et Command：[Command Class Meter, Meter Reset]

4 Notification Report Command：

：：

：

When PAN34 detect Overload, it will end Notification Report to Group1, Notification

_Type = 0x08, Notification State = 0x08. When it receive Notification Get command

with Notification Type = 0x08 and the PAN34 not in overload tatu , it will end Notifi-

cation Report, Notification Type = 0x08, Notification State = 0x00.

When PAN34 detect an overload power, it will end Notification Report to Group1.

[Command Cla Notification, Notification Report, Notification Type = 0x08,

Notification State = 0x08 (Overload)]

[Command Cla Notification, Notification Report, Notification Type = 0x08,

Notification State = 0x00 (Normal)]

5. Z-Wave’s Configuration

Configura

tion

Parameter

Function Size

(Byte)

Value Unit Default Description

1 Watt

Meter

Report

Period

2 0x01-

0x7FFF

5 720 0: Di able auto

Report

1~0x7FFF: 5

~45 hour

2 External

witch

type

1 1-2 2

1: One Pu h button

2:Two Pu h button

3 Total

moving

time of

curtain

2 0-6000 0.1

Second

0: The time depend

on Moving Range

Calibration

1~6000: 0.1 ~600

4 Watt 1 1-5 Watt 1

The thre hold i a

thre hold

judgment for motor

running or not

Watt

differential

1 0-1 1

0: It will not report

Watt when change

over 5%

1: It will report watt

value when the

differential i over 5%

6 Timer

off et for

motor

tart

running

2 0-255 0.01

econd

0-255: 0 ~ 2.55

50 = 0.5

5-1 Watt Meter Report Period:

If the etting i configured for 1hour ( et value =720), the PAN34 will report it in tant

power con umption every 1 hour to the node of Group 1. The maximum interval to

report it in tant power con umption i 45 hour (5 *32767/3600=45hr). Default

value i 1 hour. If the etting value i 0, the auto report function of meter Watt will be

di abled.

5-2 External switch type

5-2-1 One Pu h Button：

When the configuration etting i One Pu h Button, only S1 input will be valid.

The control moving command can be accepted in thi witch type while the

hutter i moving. In thi witch type, the inclu ion/exclu ion/re et function can

al o be fulfilled by pre ing S1 ju t like the operation of include button.

Autres manuels pour PAN34

Autres manuels Philio Technology Corporation Contrôleurs

Philio Technology Corporation

Philio Technology Corporation PAN34 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur