Perform FX Fog Blaster 3000 Manuel utilisateur

Fog Blaster 3000

PFX3000S Instruction Manual

CAUTION - ATTENTION - VORSICHT

RISK OF ELECTRIC SHOCK- DO NOT OPEN

RISQUE D’ELECTROCUTION - NE PAS OUVRIR

STROMSCHLAGGEFAHR - NICHT OFFNEN

In Compliance wit t e following directives: RoHS Directive (2002/95/EU) and

WEEE directive (2002/96/EU)

If t is product is no longer functional or reac ed t e end of its usable life, please

take it to an approved recycling plant.

Dear Customer,

Thank you for purchas ng the Perform FX PFX3000S. W th decades of exper ence n des gn and product on,

Perform FX are one of the lead ng manufacturers of profess onal effects and l ght ng equ pment. Th s fog

mach ne has been des gned and manufactured to the h ghest of standards, so you can be assured you have

made a good nvestment.

For your safety and to ensure you make full use of all the features ava lable, please make sure you read th s

manual n full.

Important Safety Advice:

• You must read th s manual n full before commenc ng operat on.

• The mach ne should be operated by a respons ble and competent adult only.

• Keep th s manual n a safe place for future reference.

• Heed all warn ngs and nstruct ons, both n th s manual and on the product.

• Carry and transport th s product w th care.

• Impact to th s mach ne or dropp ng may result n ser ous mechan cal fa lure. The mach ne should not be

used f t has been subjected to such nc dent.

• Turn off and unplug th s mach ne from the ma ns supply when not n use.

• Th s mach ne s not water-proof and should not be used outs de.

• In the event of any l qu d enter ng the hous ng, unplug mmed ately & contact a qual f ed eng neer.

• You must not attempt to mod fy th s un t

• The manufacturer accepts no respons b l ty for njury or damage caused as a result of not follow ng the

manual prov ded.

Protection from Electric S ock:

• Only connect th s un t to a ma ns socket w th su table tr p and RCD protect on.

• To d sconnect from the ma ns socket, always remove by the ma ns plug. Do not attempt to remove by

pull ng the ma ns cable.

• D sconnect the un t from the ma ns supply before clean ng. Clean ng should be carr ed out w th a soft, dry

cloth.

• Do not submerge or expose th s mach ne to any l qu d.

• Do not operate near exposed water or n h gh hum d ty.

• Choose a su table route for ma ns cables, ensur ng tr p hazards are avo ded and the ma ns cable s not at

r sk of be ng crushed.

• Do not open th s un t to serv ce. There are no user-serv ceable parts ns de. Any serv c ng or repa rs should

be carr ed out by a qual f ed eng neer only. Any attempt to serv ce or adapt th s un t w ll leave your

warranty vo d and could result n ser ous malfunct on or njury.

Protection from Fire:

• Do not place near sources of heat or gn t on.

• Do not cover or block any vent lat on holes.

• Check your AC wall socket w ll take the power you are apply ng to avo d overload ng the ma ns supply.

Protecting Your Mac ine From Damage:

• Always nstall n a su table locat on where v brat ons to the un t are avo ded.

• Check th s un t matches the ma ns voltage and frequency before plugg ng t n to your ma ns socket.

• In the event that any object or l qu d enters the mach ne sw tch off mmed ately, remove from ma ns and

consult a qual f ed eng neer.

• Should you exper ence any malfunct on or damage to the ma ns cable, d sconnect from the ma ns supply

mmed ately and consult a qual f ed eng neer.

• All parts should be replaced w th genu ne spare parts and carr ed out by a qual f ed eng neer.

• Do not add l qu ds of any k nd, espec ally flammable l qu ds to th s mach ne or ts ntended flu d. Use only

water based flu d, spec f cally des gned for effects mach nes.

• Use h gh qual ty water-based l qu d, recommended by your dealer to reduce clogg ng.

• Dur ng operat on ensure there s suff c ent flu d n the tank. Operat ng w thout flu d w ll damage the pump.

• If your mach ne fa ls to work d sconnect mmed ately, remove all l qu d and return n or g nal pack ng to

your dealer.

• Always dra n the flu d and water tanks before transport ng.

• Follow the clean ng and ma ntenance adv ce n th s manual.

• If your mach ne fa ls to work, d sconnect mmed ately, remove all l qu d and return n or g nal pack ng to

your dealer.

Danger of Injury or Burns:

• For operat on by adults only, ensure nstallat on s away from the reach of ch ldren.

• Never leave the mach ne runn ng unattended.

• Avo d all contact w th the heater.

• Never a m the nozzle d rectly at people.

• Use only n a well vent lated area & do not cover the mach ne vents. In order to guarantee adequate

vent lat on, allow a free a r space of at least 20cm around all s des of the mach ne.

• Effects flu ds can cause rratat on and njury, handle w th care and keep out of the reach of ch ldren. Avo d

contact w th the eyes and sk n, f th s occurs r nse w th warm water. If ngested call a doctor mmed ately.

Before Use:

Before commenc ng setup check the mach ne has not been damaged n trans t. In the event there s any

damage to the hous ng, cable or nternal components contact your dealer mmed ately.

Contents Includes:

User Manual

PFX3000s

Power Cable

W reless remote and rece ver

Instruct ons

Specifications:

Code: PFX3000S

Ma ns Supply: 240Vac 50Hz

Power: 3000 Watts

Heat Up T me: 5 m n

D mens ons: 480 x 265 x 220mm

We ght: 10kg

Features Include:

A 3000 watt heater.

6L Flu d Tank.

Uses water based fog flu d.

W reless Remote Control.

DMX controllab l ty, 1 channels of control.

Features:

• Powerfull 3000 Watt Heater

• Very H gh Output

• DMX Control

• Large Flu d Tank

Description:

The PFX3000S s a powerful smoke mach ne that can be floor mounted or hung from truss.

1. Heater Nozzle: Smoke output, th s w ll get very hot n operat on - do not touch.

2. Fluid Tank: F ll the flu d tank w th standard fog l qu d, do not sp ll the l qu d as th s could damage the

electron cs.

3. Hanging Bracket: Used to mount to truss, always use a safety w re.

4. DMX Input: Female 3 p n used to connect from a DMX controller or prev ous DMX f xture

5. DMX Output: Male 3 p n used to connect to next DMX f xture n the cha n.

6. Power Switc : Used to turn the smoke mach ne on and off.

7. Circuit Breaker: If th s tr ps reset once, f t tr ps aga n, there may be a problem w th the mach ne.

8. Mains Input: Plug the suppl ed PowerCon ma ns cable n here.

9. Remote Control: For connect on of the w reless rece ver.

10. Menu Button: used to browse the setup menu.

11. Up Button: Used to adjust sett ng n the menu.

12. Down Button: Used to adjust sett ng n the menu

13. Enter Button: Used enter sub menus n the menu.

14. Eye Bolt: Used to connect safety w re.

❶

❼

❽

❾

❻ ❺ ❿

⓫⓬ ⓭ ⓮

❷

❸

❹

Set Up Menu:

The setup menu s used to adjust the d fferent parameters of the smoke mach ne.

The MENU button s used to nav gate through those menu opt ons.

• Addr:

Press enter, use the up and down buttons to adjust the DMX address, then press enter to save sett ngs.

• rENo:

Press enter to adjust the sett ngs.

Here you have 5 sett ng: Gear, CH1, CH2, CH3, CH4, OFF, use the up and down buttons to choose one and

then press enter.

• Gear:

Allows you to use all 4 buttons, A=25% fog output, B=50% Fog output, C=75% output, D=100% fog output,

CH1,CH2,CH3,CH4 by choos ng one of these you can choose what button act vates the fog mach ne at full

output, th s mode s useful when controll ng mult ple un ts from one controller. So by select ng CH1 th s w ll

mean that the smoke mach ne works from button A, CH2 button B and so on.

• NoFU:

Turns the low flu d funct on on and off. When the mach ne s low on flu d the d splay w ll flash. It s a good

deal to leave th s funct on ON(yes) as low flu d n the tank can damage the pump. Press enter and use the up

and down to select yes or no, then press enter aga n.

First Time Operation - Panel Control:

Before you start us ng th s un t, please check there s no transportat on damage, should there be any, please

do not use the dev ce and contact your dealer mmed ately.

The PFX3000S s des gned to be used w th water based fog l qu d, NEVER OIL BASED.

Put the smoke mach ne on a flat stable surface or hang from a su table truss, make sure you use a safety w re.

Make sure no one can put any body part close to the heater output

Unscrew the L d on the flu d bottle, f ll up w th a su table fog l qu d, make sure not to over f l. Then screw the

plast c cap back on. Make sure the tank never runs dry dur ng operat on.

Connect the PFX3000S to a su table ma ns supply.There s a s mple 4 button menu w th LCD d splay on the

back of the un t, the 4 buttons control menu, up, down and enter.

When you f rst turn on the fog mach ne you w ll need to wa t for around 3-5 m nutes for the heater to warm

up. Then you w ll get access to the controls.

Press the menu button to scroll through opt ons and use the up down buttons to make changes.

First Time Operation Wireless Controller:

Before you start us ng th s un t, please check there s no transportat on damage, should there be any, please

do not use the dev ce and contact your dealer mmed ately.

• The PFX3000S s des gned to be used w th water based fog l qu d, NEVER OIL BASED.

• Put the smoke mach ne on a flat stable surface or hang from a su table truss, make sure you use a safety

w re. Make sure no one can put any body part close to the heater output.

• Unscrew the L d on the flu d bottle, f ll up w th a su table fog l qu d, do not to overf ll. Screw the plast c cap

back on and ensure the tank never runs dry dur ng operat on.

• Plug n the w reless rece ver nto the socket on the back labelled remote control.

• Connect the PFX3000S to a su table ma ns supply.

• When you f rst turn on the smoke mach ne you w ll need to wa t for around 3-5 m nutes for the heater to

warm up, then you w ll ga n access to the controls. Adjust the sett ngs n the menu to su t.

• Once heated the smoke mach ne can be controlled v a the w reless remote control.

First Time Operation Wit DMX:

Before you start us ng th s un t, please check there s no transportat on damage, should there be any, please

do not use the dev ce and contact your dealer mmed ately.

• The PFX3000S s des gned to be used w th water based fog l qu d. NEVER OIL BASED.

• Put the smoke mach ne on a flat stable surface or hang from a su table truss, make sure you use a safety

w re. Make sure no one can put any body part close to the heater output.

• Unscrew the l d on the flu d bottle, f ll up w th a su table fog l qu d, do not to overf ll. Screw the plast c cap

back on and ensure the tank never runs dry dur ng operat on.

• Plug n a su table DMX controller v a the 3 p n DMX socket.

• Connect the PFX3000S to a su table ma ns supply.

• When you f rst turn on the smoke mach ne you w ll need to wa t for around 3-5 m nutes for the heater to

warm up and then you w ll ga n access to the controls.

• Set a DMX address v a the 4 button menu d splay.

• Once heated the smoke mach ne can be controlled by 1 channels of DMX, 1=volume output.

Over ead Rigging:

The nstallat on must be carr ed out by a qual f ed eng neer only. Improper nstallat on can result n njur es or

damage to property. Overhead r gg ng requ res exper ence, work ng loads should be adhered to and cert f ed

mater als should be used. The nstalled dev ce should be regularly nspected for safety.

• Make sure the work ng area s clear from people and obstruct ons dur ng r gg ng, de-r gg ng and serv c ng.

• Locate the smoke mach ne n a well vent lated area away from flammable mater als and l qu ds. The smoke

mach ne needs to be 50cm away from surround ng walls and f xtures.

• The smoke mach ne should be nstalled out of reach of people and not where people are seated, walk ng or stand ng.

• When mount ng make sure the nstallat on po nt can take the we ght.

• Make sure a safety cha n or w re s always used and can take the we ght of the smoke mach ne. The safety

bond should not be used as a pr mary support.

• The mach ne should be well f xed and free from sw ng ng.

• Do not cover any vent lat on holes.

• D sconnect the power when the mach ne s not n use.

• The operator must make sure the smoke mach ne has been nstalled correctly to all the necessary

gu del nes before each use. The nstallat on should be nspected every 6 months.

Maintenance:

• Do not allow l qu d to become contam nated. Always replace the cap on the l qu d conta ner mmed ately

after f ll ng.

• After every 40 hours of operat on, or f the un t s not to be used for one month, It s recommended to run a

clean ng solut on of 20% clear v negar and 80% d st lled water through the system to prevent clogg ng n the

heater. Th s should be carr ed out n a well-vent lated room.

• Always empty the flu d and water tanks after every use. Use a dry cloth to w pe down the outs de of the fog

mach ne. Make sure the power cable s d sconnected from the ma ns supply.

• Make sure the ma ns cable s n mpeccable cond t on and should be replaced when a small defect s

detected.

• All other ma ntenance should be carr ed out by a qual f ed eng neer.

DMX BASICS:

• DMX s short for “d g tal mult plexer”, wh ch s a un versal protocol des gned for the enterta nment ndustry.

It allows control of ntell gent f xtures l ke scanners, mov ng heads, LED par cans, d mmer packs & effects

mach nes etc.

• DMX allows you to control many f xture channels, normally up to 512, w th vary ng channels from 0-255 (0-

100%).

• Th s w ll g ve control of channels such as gobo select on, movement, colours, d mm ng and t m ng to name

just a few.

• DMX s a very good system, as all th s nformat on can be sent down one cable. Used n conjunct on w th a

DMX controller w th memory, all of your channel sett ngs can be saved and recalled eas ly.

• DMX was des gned so that all manufacturers can use the same protocol/language to control the r f xtures,

allow ng the end user to use any make of f xture from the r DMX controller as long as both are DMX

compat ble, and the controller has enough channels to control the f xture that s attached.

• F xtures have an nput and output DMX socket, allow ng you to connect from the controller to the f rst

f xture then from that f xture to the next (th s s often referred to as “da sy cha n ng”).

• Sockets are normally 3 p n XLR but can be 5 p n XLR.

DMX f xtures need to have a DMX address set, th s s so they can then decode the correct nformat on from

the controller. Th s s normally done by a d g tal d splay panel, where the address can be changed by s mple

up and down buttons; the address ranges from 1-512. Alternat vely t may be controlled by a row of small

sw tches, called d p sw tches; on th s type system, the requ red address s then converted to a b nary number.

DMX Connector Wiring

3 P n w r ng s more common, but the 5 p n conf gurat on s often used on larger equ pment. W th the 5 p n

conf gurat on, not all p ns are used, though t s worth check ng the f xture manual, as some equ pment use

the extra p ns for low voltage control. 5 P n connectors are deal so there s no confus on over m xer leads and

DMX leads n larger r gs. Send ng a m xers 48v phantom power down a DMX cable could damage the DMX

l ght or f xture.

If mak ng cables, always use su table DMX cable and do not connect p n 1 GND to the outer cas ng of the

connector as you m ght do w th aud o cables, as th s may cause errat c behav our from your f xture.

Do not make “Y” leads to spl t cables to f xtures; always use the n and out sockets or a DMX spl tter, as aga n

th s may cause errat c behav our from your f xture.

We recommend you to plug a DMX term nator nto any f xture that hasn’t got a DMX lead connected from the

output socket to another f xture; Th s aga n s to reduce unexpected behav our. A DMX term nator s s mply a

male XLR plug w th 120 ohm, ¼ watt res stor soldered across p n 2 & 3.

3 PIN 5 PIN

PIN 1 GND PIN 1 GND

PIN 2 - PIN 2 -

PIN 3 + PIN 3 +

PIN 4 NOT USED

PIN 5 NOT USED

Each f xture takes up 5 DMX Channels (See Above)

You have a cable from the controller to the f rst f xture cable, then from f rst to second and so on. The last

l ght then has a DMX term nator plugged n.

F xture 1 would be set to DMX address 1

F xture 2 would be set to DMX address 6

F xture 3 would be set to DMX address 11

F xture 4 would be set to DMX address 16

When sett ng these addresses, ensure that the f xture addresses dont overlap. You can set two f xtures to the

same address as long as they have the same channel layout, they w ll then perform n the same way.

We recommend you to read manuals for your DMX f xture and controller n full. Some controllers tell you

what each f xture address needs to be, and some equ pment w ll need other sett ngs changed before they w ll

work.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Perform FX Machine à brouillard

Perform FX

Perform FX Mini LED Fog 400 Manuel utilisateur

Manuels Machine à brouillard populaires d'autres marques

Antari

Antari ICE Manuel utilisateur

Boost

Boost BOOST-FOG400LED-BK Manuel utilisateur

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manuel utilisateur

EuroLite

EuroLite ZEITGEIST FOG-1200 Manuel utilisateur

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manuel utilisateur

PROEL

PROEL DRAGO HEAVY PLFD150HY Manuel utilisateur

Sparklyn

Sparklyn Y846 Manuel utilisateur

Magicfx

Magicfx CO2 Gun Manuel utilisateur

Ibiza

Ibiza LSM500LAS Manuel utilisateur

Antari

Antari M-5 Manuel utilisateur

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manuel utilisateur

High End

High End F-100 Manuel utilisateur

Chauvet

Chauvet ARENA 2100 FLEX Manuel utilisateur

Antari

Antari X FAZER Manuel utilisateur

Beamz

Beamz F1600 Manuel utilisateur

Sagitter

Sagitter SG ARS900C Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-STF-480 Manuel utilisateur

Orion

Orion OT-U250PP Mode d’emploi