Pequod Zephyrus 15.1 Manuel utilisateur
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
User guide
Zephyrus 15.1
Two way passive coaxial
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
Index
1 Technical Specications
2 Unpacking and Checking
3 Cables and Set-up
4 Installation and System Design
5 Accessories
6 Maintenance and Surface Protection
7 Warranty
8 Authenticity
Zephyrus 15.1
Two way passive coaxial
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
1 Technical Specications
Zephyrus is a compact product desi-
gned around a 5 inch coaxial high per-
formance speaker. It has a mid woofer
of 5 inches with a horn loaded and coa-
xial driver capable of high resolution at
high frequency. The body is realized in
composite material, light yet resistant,
capable of withstanding shock and at-
mospheric agents. This is the perfect
product to create sound quality loyal
systems that respects vocal quality. It is
also ideal to create satellite + subwoofer
systems that maintain high quality with
low encumbrance. It excels in its goal of
sonorizing small rooms or areas in clubs.
Multiple Zephyrus speakers allow for an
equal diusion of extreme high quality
sound in an open area. Another use is
the connection to a studio system or
a PC workstation where sound quality
and sound detail has to be immediately
recognizable. Pairing the Zephyrus with
the Borea sub (ovoid system) allows to
create a full range system, compact and
dynamic, and is therefore suggested.
The passive crossover, realized without
compromise, selecting the most high
quality components, allows control of
the Zephyrus with a single amplication
channel.
TYPE
FREQUENCY
RESPONSE
TOTAL
SENSITIVITY
SPL MAX
LOW - MEDIUM
FREQUENCIES
HIGH
FREQUENCIES
NOMINAL
IMPEDANCE
POWER
HANDLING
MANAGE
RECOMMENDED
AMPLIFIER
DISPERSION
CONSTRUCTION
MATERIALS
FINISH
PROTECTIVE
GRILLES
CONNECTORS
DIMENSIONS
(WITH SUPPORT)
WEIGHT
Two way passive coaxial
70 Hz - 18 KHz (-3dB)
92 dB 1W/1m with passive crossover
114 dB with 300 W
5” woofer @ 8 Ohm 300W continuo-
us power handling , sensivity 92 dB
1W/1m
HF compression driver with high tech
polymer diaphragm @ 8 Ohm 50W
continuous power handling , sensivity
105dB 1W/1m
4 Ohm with 2 way passive crossover
300W @ 4 Ohm with amplier
2 Ch amplier to a couple of Zephyrus
loudspeakers (passive crossover pro-
vided, for each Zephyrus) .If very high
output is needed we recommend to use
a DSP : High-pass lter @70Hz, 12 dB/
oct. or higher slope
Otherwise as Satellite with subwoofer :
Amplier+DSP to match to subwoofer.
High-pass lter @90Hz, 12 dB/oct. or
higher slope. Inner thermal protection
device provided, to avoid overdrive.
2 channel amplier, around 350W on
each channel @ 4 ohm stable
70 deg conical
Fiber-reinforced composite, stainless
steel
all ral color and texture on order
Zephyrus is usually sold with this grid
to protect the 5” coax ,as standard
Zephyrus has,as exit, 2 pole OFCop-
per high quality cable ,1,5 sq.mm each
pole, to be connected to Neutrik NL2,
NL4 or custom
(W) 255mm (H) 332mm (D)350mm
(W) 10 inch (H) 13 inch (D) 13,7inch
3,5 Kg (7,7 lb)
255mm (10 inch )350mm (13,7 inch )
332mm (13 inch )
USER GUIDE
2: Unboxing
The Zephyrus system, like every other Pequod
product, is built with high standards of control
and quality. At the end of the production pro-
cess and before packaging, each system is te-
sted: acoustically measured and recorded in our
company database. For each Zephyrus serial
number, we have the related test les recorded
in the archive. Before being packed in its box we
complete an inspection of surfaces and structu-
res. Units are packed into wooden crates or he-
avy cardboard boxes with internal foam padding
before shipping.
Extraction from box:
The Zephyrus weighs 3,5 Kg (7,7 lb) each, and is
taken from the box simply following the steps
shown here. Keep the packaging for further sto-
rage or transportation, unless units are to be
permanently installed.
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
1: Carefully cut tape and
open carboard box
2: Remove packing materials
and save for re-use
3: lift speaker body with
both hands when ready
USER GUIDE
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
3 Wiring and Settings
Zephyrus has an input made with a high quality 2p OFC cable (with standard NL4FC male connec-
tor).
The 2p cable can be terminated with an NL2, NL4 or custom connector, or connection with another
cable, using terminal block / welding and heat shrink insulation (see Fig).
In case of custom realization by the installer of the connection cables, we recommend specifying
installation-grade Low Smoke Zero Halogen (LSZH) cables for permanent installations. The cables
should use Oxygen Free Copper (OFC) of grade C11000 or above. For distances of over 15 meters
between Zephyrus and ampli we recommend increasing the section of the cable poles to 4 sq.mm,
to avoid excessive emission level losses. For lengths of less than 15 m, you can use 2-pole cables,
each with a section of 2.5 sq.mm.
USER GUIDE
Cable connection
Zephyrus cable To amplier cable
Welding
Welding
Terminal block
heat shrink tubing
heat shrink tubing
Box
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
NL2 ( +1 -1 )
NL4
or Custom
NL2 ( +1 -1 )
NL4
or Custom
2p
2p
2p
2p
2p
2p
SUB
SUB
SUB
USER GUIDE
2 ch sat
1 ch sub
3 ch ampli
2 ch sat
2 ch sub
4 ch ampli
Amplier + DSP
Amplier + DSP
DSP general settings:
1) Stand alone: Just if very high output is needed
we recommend to use a DSP: High-pass lter @
70Hz, 12 dB / oct. or higher slope
2) Zephyrus as Satellite with subwoofer: Amplier +
DSP to match to subwoofer.
Zephyrus: High-pass lter @ 90Hz, 12 dB / oct. or
higher slope. Sub: (Band pass)
High-pass lter @ 20Hz, 12 dB / oct. or higher slope
Low pass lter @ 90Hz, 12 dB / oct. or higher slope
Gain and Time Alignment: it depends on Subwoofer
utilized
Connection schemes
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
4 Installation and system design
For private or enclosed areas as rst choice Fig 1, or multipoint source Fig 2 e Fig 2A. Or as a Satel-
lite with subwoofer for small areas (home theater Fig 3) or for a small audience of a live event. Also
used as a ller for medium-high frequencies in areas that require such sound reinforcement, Fig 4.
Finally, as a valuable satellite for a console or a PC workstation, Fig 5.
In any case, optimal acoustic coverage is obtained by orienting the central axis coming out of the
5 “coax towards the heads of the listeners, lifting the speakers from the ground.
USER GUIDE
Fig.1
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
Fig.2
Stage
Fig.2 A
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
Stage
Screen
Sub
Sub
Fig.3 Fig.4
Pequod Acoustics Srl.
Via del Madonnone 25, Florence, Italy
www.pequodacoustics.com
Borea Sub
Fig.5
Autres manuels Pequod Intervenants
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur