Pepperl+Fuchs HiD2030 Manuel utilisateur

ISO9001

Functional Safety

SMART Transmitter Power

Supply

HiD2030(SK)

Manual

With regard to the supply of products, the current issue of the following document is applicable:

The General Terms of Delivery for Products and Services of the Electrical Industry, published by the Central

Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most

recent version as well as the supplementary clause: "Expanded reservation of proprietorship"

Worldwide

Pepperl+Fuchs Group

Lilienthalstr. 200

68307 Mannheim

Germany

Phone: +49 621 776 - 0

E-mail: info@de.pepperl-fuchs.com

North American Headquarters

Pepperl+Fuchs Inc.

1600 Enterprise Parkway

Twinsburg, Ohio 44087

USA

Phone: +1 330 425-3555

E-mail: [email protected].com

Asia Headquarters

Pepperl+Fuchs Pte. Ltd.

P+F Building

18 Ayer Rajah Crescent

Singapore 139942

Phone: +65 6779-9091

E-mail: [email protected]

https://www.pepperl-fuchs.com

Functional Safety HiD2030(SK)

Contents

2021-09

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Content of this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 Symbols Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.5 Standards and Directives for Functional Safety . . . . . . . . . . . . . . . . . . . 9

3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.1 System Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.2 Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.3 Safety Function and Safe State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.4 Characteristic Safety Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.5 Useful Lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4 Mounting and Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.1 Proof Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

6 Maintenance and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7 List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Functional Safety HiD2030(SK)

Contents

2021-09

Functional Safety HiD2030(SK)

Introduction

2021-09

1 Introduction

1.1 Content of this Document

This document contains information for usage of the device in functional safety-related

applications. You need this information to use your product throughout the applicable stages

of the product life cycle. These can include the following:

•Product identification

•Delivery, transport, and storage

•Mounting and installation

•Commissioning and operation

•Maintenance and repair

•Troubleshooting

•Dismounting

•Disposal

The documentation consists of the following parts:

•Present document

•Instruction manual

•Manual

•Datasheet

Additionally, the following parts may belong to the documentation, if applicable:

•EU-type examination certificate

•EU declaration of conformity

•Attestation of conformity

•Certificates

•Control drawings

•FMEDA report

•Assessment report

•Additional documents

For more information about Pepperl+Fuchs products with functional safety,

see www.pepperl-fuchs.com/sil.

Note

This document does not substitute the instruction manual.

Note

For full information on the product, refer to the instruction manual and further documentation

on the Internet at www.pepperl-fuchs.com.

2021-09

Functional Safety HiD2030(SK)

Introduction

1.2 Safety Information

Target Group, Personnel

Responsibility for planning, assembly, commissioning, operation, maintenance,

and dismounting lies with the plant operator.

Only appropriately trained and qualified personnel may carry out mounting, installation,

commissioning, operation, maintenance, and dismounting of the product. The personnel must

have read and understood the instruction manual and the further documentation.

Intended Use

The device is only approved for appropriate and intended use. Ignoring these instructions

will void any warranty and absolve the manufacturer from any liability.

The device is developed, manufactured and tested according to the relevant safety standards.

Use the device only

•for the application described

•with specified environmental conditions

•with devices that are suitable for this safety application

Improper Use

Protection of the personnel and the plant is not ensured if the device is not used according

to its intended use.

Functional Safety HiD2030(SK)

Introduction

2021-09

1.3 Symbols Used

This document contains symbols for the identification of warning messages and of informative

messages.

Warning Messages

You will find warning messages, whenever dangers may arise from your actions.

It is mandatory that you observe these warning messages for your personal safety and in order

to avoid property damage.

Depending on the risk level, the warning messages are displayed in descending order

as follows:

Informative Symbols

Action

This symbol indicates a paragraph with instructions. You are prompted to perform an action

or a sequence of actions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and plants,

or result in their complete failure.

Note

This symbol brings important information to your attention.

2021-09

Functional Safety HiD2030(SK)

Product Description

2 Product Description

2.1 Validity

This manual is only valid for devices with a part number greater than #70122700.

Contact your Pepperl+Fuchs representative for information about older devices.

2.2 Function

General

This isolated barrier is used for intrinsic safety applications.

Digital signals may be superimposed on the analog values in the explosion hazardous

or non-explosion hazardous area, which are transferred bidirectionally.

A separate fault bus is signaled if the input signal is outside the range from 0.2 mA to 24 mA.

The fault conditions can be monitored via a Fault Indication Board.

This device mounts on a HiD Termination Board.

HiD2030

The device provides a fully floating supply to power 2-wire SMART transmitters

in the explosion-hazardous area, and repeats the current to drive a non-explosion hazardous

area load. It is also used with 2-wire current sources.

In the non-explosion hazardous area, the signal current is repeated to drive a load (source).

HiD2030SK

The device provides a fully floating supply to power 2-wire SMART transmitters

in the explosion-hazardous area, and repeats the current to drive a non-explosion hazardous

area load. It is also used with 2-wire current sources.

In the non-explosion hazardous area, the signal current is repeated with a passive

current output (sink).

Note

See corresponding datasheets for further information.

Functional Safety HiD2030(SK)

Product Description

2021-09

2.3 Interfaces

The device has the following interfaces:

•Safety relevant interfaces: input I, input II, output I, output II

•Non-safety relevant interfaces: separate fault bus

2.4 Marking

2.5 Standards and Directives for Functional Safety

Device specific standards and directives

System-specific standards and directives

Note

For corresponding connections see datasheet.

Pepperl+Fuchs Group

Lilienthalstraße 200, 68307 Mannheim, Germany

Internet: www.pepperl-fuchs.com

HiD2030, HiD2030SK Up to SIL 2

Note

If you design the safety loops in homogeneous redundancy (HFT = 1), you can use the devices

in applications up to SIL 3.

Functional safety IEC/EN 61508, part 1 –7, edition 2010:

Functional safety of electrical/electronic/programmable electronic

safety-related systems (manufacturer)

Functional safety IEC 61511-1:2016+COR1:2016+A1:2017

EN 61511-1:2017+A1:2017

Functional safety –Safety instrumented systems for the process

industry sector (user)

2021-09

Functional Safety HiD2030(SK)

Planning

3 Planning

3.1 System Structure

3.1.1 Low Demand Mode of Operation

If there are two control loops, one for the standard operation and another one

for the functional safety, then usually the demand rate for the safety loop is assumed to be less

than once per year.

The relevant safety parameters to be verified are:

•the PFDavg value (average Probability of dangerous Failure on Demand)

and the T1 value (proof test interval that has a direct impact on the PFDavg value)

•the SFF value (Safe Failure Fraction)

•the HFT architecture (Hardware Fault Tolerance)

3.1.2 High Demand or Continuous Mode of Operation

If there is only one safety loop, which combines the standard operation and safety-related

operation, then usually the demand rate for this safety loop is assumed to be higher

than once per year.

The relevant safety parameters to be verified are:

•the PFH value (Probability of dangerous Failure per Hour)

•Fault reaction time of the safety system

•the SFF value (Safe Failure Fraction)

•the HFT architecture (Hardware Fault Tolerance)

3.1.3 Safe Failure Fraction

The safe failure fraction describes the ratio of all safe failures and dangerous detected failures

to the total failure rate.

SFF = (s + dd) / (s + dd + du)

A safe failure fraction as defined in IEC/EN 61508 is only relevant for elements or (sub)systems

in a complete safety loop. The device under consideration is always part of a safety loop

but is not regarded as a complete element or subsystem.

For calculating the SIL of a safety loop it is necessary to evaluate the safe failure fraction

of the elements and subsystems, but not of a single device.

Nevertheless the SFF of the device is given in this document for reference.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pepperl+Fuchs Alimentation

Pepperl+Fuchs

Pepperl+Fuchs SIL KCD2-STC-1.SP Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs FB3205B3 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs KF**-CRG2-Ex1.D Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs HiD2022 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs HiD2025 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs ENT-DC-30 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs HD2 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1550 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs HiD2024 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.10.R Manuel

Pepperl+Fuchs

Pepperl+Fuchs PSU1100-J1-AC Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.10 Manuel

Pepperl+Fuchs

Pepperl+Fuchs PS3500 N+1 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs KF**-CRG2-Ex1.D Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-48.5 Manuel

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.20 Manuel

Pepperl+Fuchs

Pepperl+Fuchs HiC2027 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.5 Manuel

Pepperl+Fuchs

Pepperl+Fuchs KFD2-STC4-Ex Series Guide de l'utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PSU1100-J1-DC Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.20.R Manuel

Pepperl+Fuchs

Pepperl+Fuchs KLD2-PR-Ex1.IEC. Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-12.16 Manuel

Pepperl+Fuchs

Pepperl+Fuchs KCD2-STC-1 Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur