Pentair PENBERTHY GL Manuel

PENBERTHY

Jet

Pumps

Models GL, GH - Gas Operated

Installation, Operation and Maintenance Instructions

Section: 1000

I.O.M.: 1951

Issued: 05/15

Replaces: 12/04

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

TABLE OF CONTENTS

Product Warranty . . . . . . . . . iii

1.0 About the Manual . . . . . . . . . 1

2.0 Introduction . . . . . . . . . 1

2.1 Features and Specifications. . . . . . . 1

2.2 Design Ratings at Max. and Min. Operating Temperatures . . 1

2.3 Application Data . . . . . . . . 1,2

3.0 Inspection and Performance Confirmation. . . . . . 2

3.1 Receiving Inspection . . . . . . . 2

3.2 User's Rating Inspection. . . . . . . . 2

4.0 Installation . . . . . . . . . . 2

4.1 Effect of Related Piping and Precautions . . . . . 3

5.0 Operation . . . . . . . . . . 4

5.1 Pre-Operational Check. . . . . . . . 4

5.2 Operating . . . . . . . . . 4

6.0 Maintenance . . . . . . . . . 4

6.1 Preventative Maintenance . . . . . . . 5

6.2 Troubleshooting . . . . . . . . 5

7.0 Disassembly-Reassembly . . . . . . . . 5

8.0 Disposal at End of Useful Life . . . . . . . 5

9.0 Telephone Assistance . . . . . . . . 6

10.0 Exploded Parts Drawing . . . . . . . . 7

TABLES AND FIGURES page

Table 1 Design Ratings at Max. and Min. Operating Temperatures . . 1

Table 2 Troubleshooting . . . . . . . 5

Figure 1 Typical Installation Schematic Gas Operated Pumping Gases . 4

Figure 2 Typical Installation Schematic Steam Operated Pumping Water . 4

Figure 3 Exploded Parts Drawing . . . . . . 7

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

PENBERTHY PRODUCT WARRANTY

Pentair Valves & Controls Black Mountain warrants its Penberthy products as designed and

manufactured by PV&C Black Mountain to be free of defects in the material and workmanship for a

period of one year after the date of installation or eighteen months after the date of manufacture,

whichever is earliest. PV&C Black Mountain will, at its option, replace or repair any products which fail

during the warranty period due to defective material or workmanship.

Prior to submitting any claim for warranty service, the owner must submit proof of purchase to PV&C

Black Mountain and obtain written authorization to return the product. Thereafter, the product shall be

returned to PV&C in Black Mountain, North Carolina, with freight paid.

This warranty shall not apply if the product has been disassembled, tampered with, repaired or

otherwise altered outside of PV&C Black Mountain factory, or if it has been subject to misuse, neglect

or accident.

The responsibility of PV&C Black Mountain hereunder is limited to repairing or replacing the product at

its expense. PV&C Black Mountain shall not be liable for loss, damage or expenses related directly or

indirectly to the installation or use of its products, or from any other cause or for consequential

damages. It is expressly understood that PV&C Black Mountain is not responsible for damage or

injury caused to other products, buildings, personnel or property, by reason of the installation or use of

its products.

THIS IS PV&C BLACK MOUNTAIN’S SOLE WARRANTY AND IN LIEU OF ALL OTHER

WARRANTIES, EXPRESSED OR IMPLIED WHICH ARE HEREBY EXCLUDED, INCLUDING IN

PARTICULAR ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE.

This document and the warranty contained herein may not be modified and no other warranty,

expressed or implied, shall be made by or on behalf of PV&C Black Mountain unless made in writing

and signed by the General Manager or Director of Engineering of PV&C Black Mountain.

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

INSTALLATION, OPERATION and MAINTENANCE MANUAL

FOR PENBERTHY MODELS GL & GH JET PUMPS

1.0 About the Manual

This manual has been prepared as an aid and guide for personnel involved in installation or

maintenance. All instructions must be read and understood thoroughly before attempting any

installation, operation or maintenance.

Failure to follow any instruction could possibly result in a malfunction of the jet pump with

resulting sudden release of pressure, property damage or severe physical injury.

IMPORTANT: Penberthy does not have any control over the manner in which its jet pump is handled,

installed or used. Penberthy cannot and will not guarantee that a jet pump is suitable or compatible for

the user's specific application.

2.0 Introduction

2.1 Features and Specifications

Penberthy gas operated jet pump models GL and GH are designed primarily for exhausting,

evacuating, and priming using steam or air as the operating medium; and for pumping water

using steam as the operating medium. They can also be used with other gases as the

operating medium.

2.2 Design Ratings at Maximum and Minimum Operating Temperatures

MATERIAL

BODIES

NOZZLES

Iron 80 psig [550 kPaG] at -20°F [ -29°C] to +150°F [66°C]

50 psig [340 kPaG] at +350°F [177°C] 200 psig [1380 kPaG] at -20°F [ -29°C] to +400°F [204°C]

Bronze 200 psig [1380 kPaG] at -20°F [ -29°C] to +150°F [66°C]

125 psig [ 860 kPaG] at +400°F [204°C] 200 psig [1380 kPaG] at -20°F [ -29°C] to +400°F [204°C]

316 STS 200 psig [1380 kPaG] at -150°F [-101°C] to +150°F [66°C]

125 psig [ 860 kPaG] at +400°F [ 204°C] 200 psig [1380 kPaG] at -150°F [-101°C] to +400°F [204°C]

Table 1

To determine the maximum allowable working pressure for a specific temperature within the

design limits stated above, the user should refer to Penberthy dimension sheets, or when

provided, the specifically stated design limits on a Penberthy product proposal.

2.3 Application Data

The model GL is intended to operate between 60 psig (410 kPaG) and 150 psig (1030 kPaG)

steam pressure against moderate or zero discharge head. The model GH is intended to

operate between 20 psig (140 kPaG) and 150 psig (1030 kPaG) steam pressure against

moderate to substantial discharge head.

Note: For specific application data within the above ranges, the user should consult the

Penberthy product proposal for the specific model and size jet pump, or should request

Penberthy to supply the applicable technical data bulletin.

WARNING

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

Under no circumstances should these design ratings or application data be exceeded.

Exceeding design ratings or application data may cause bursting of steam jet pump, discharge

of live steam, objectionable noise and vibration, loosening of joints, leaks and suction flow

reversal, resulting in severe physical injury or property damage.

3.0 Inspection and Performance Confirmation

3.1 Receiving Inspection

Upon receipt of jet pump, check all components carefully for damage incurred in shipping. If

damage is evident or suspected, do not attempt any installation. Notify carrier immediately

and request damage inspection.

3.2 User's Rating Inspection

The user should confirm that:

1. The jet pump size (cast on side of body) and model designation (stamped on nozzle hex

flats) conforms to the description on the user's purchase order.

2. The operating conditions described in the purchase order agree with the actual operating

conditions at the installation site.

3. The actual operating conditions at the installation site are within the applications data

shown on the Penberthy Technical Data Bulletin or product proposal referred to above.

4. The materials of construction of the jet pump are compatible with both the contained fluid

and the surrounding atmosphere in the specific application.

If the size, model or performance data of the jet pump as received does not conform with any

of the criteria above, do not proceed with installation. Contact an authorized Penberthy

distributor for direction on how to proceed.

4.0 Installation

Note: The user should refer to Penberthy dimension sheets or Penberthy product proposal to obtain

dimensional information for specific size and model jet pump.

Check the exploded view Figure 3 for the location of operating, suction and discharge connections to

insure correct hook up.

WARNING

SAFETY INSTRUCTIONS

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

4.1 Effect of Related Piping and Precautions

1. Penberthy gas operated jet pump models GL and GH may be installed and

operated in any position.

2. Jet pumps should be installed with pipe and fittings which provide minimum

resistance to fluid flow. Pipe line friction losses must always be a consideration

when estimating jet pump performance.

3. It is recommended that provisions be made for pressure gage connections near

the inlet, suction and discharge connections of the jet pump. If operating

difficulties are encountered at any time, it may become necessary to install

pressure gages to identify the problem.

4. Steam must not have over 20°F (-7°C) of superheat, or performance will differ

from that published on Penberthy Technical Data Bulletin or product proposal

referred to above.

5. When pumping liquids, suction piping should be sized so that the velocity of the

liquid does not exceed 4 feet per second. This is almost always automatically

obtained when the suction line is the same pipe size as the suction connection.

6. Install a valve in the suction line if it is desirable to:

a. Prevent contamination of suction fluid by the motive fluid at start up.

b. Prime a centrifugal pump.

c. Throttle suction flow.

7. When a gas operated jet pump is used to lift liquids by suction or vacuum, the jet

pump should be located as close to the level of the liquid as practical. However,

any liquid entrained into the jet pump, other than water when using steam as the

operating medium, may cause the jet pump to stop pumping, resulting in a

possible suction flow reversal.

8. Discharge piping should be sized as short as possible and with the least number

of turns and restrictions. Discharge piping friction losses must always be

considered when estimating jet pump performance. Increase discharge line pipe

size if necessary to minimize loss.

9. Do not impose system piping loads on a jet pump. The unit is not designed to be

a load bearing fitting.

10. All piping should be clean and free of foreign materials which could clog the jet

pump.

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

5.0 Operation

5.1 Pre-Operational Check

1. Assure that all installation procedures have been completed.

2. Assure that any restrictions in the discharge line have been removed.

3. Assure that any discharge line valves are fully open.

4. Assure that suction line valve, if installed, is fully closed.

5.2 Operating

1. Open the motive valve quickly.

2. Open the suction line valve, if any.

3. Regulate the discharge pressure as desired, to a value within the capability

published on Penberthy Technical Data Bulletin or product proposal referred to

above.

4. For pump priming applications, when evacuation is completed, close the suction

valve and immediately start the centrifugal pump. Then shut off the motive valve

to the jet pump.

6.0 Maintenance

Maintenance should only be undertaken by qualified, experienced personnel who are familiar

with this equipment and have read and understood all the instructions in this manual. Do not

proceed with any maintenance unless the jet pump has been relieved of all pressure or

vacuum, has been allowed to reach ambient temperature and has been drained or purged of all

fluids. Failure to return to ambient conditions may result in personal injury or property

damage.

CAUTION

Figure 1

Typical Installation

Schematic Gas Operated

Pumping Gases

Figure 2

Typical Installation

Schematic Steam Operated

Pumping Water

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

6.1 Preventative Maintenance

The following items should be regularly monitored for purposes of maintenance:

1. Jet pump units for corrosion or debris build up

2. Piping and fittings for corrosion or debris build up

3. All connections for tightness

4. Strainers for debris build up

The user must determine upon evaluation of his or her own application and the factors stated

above an appropriate maintenance schedule most suitable for his or her specific application.

6.2 Troubleshooting

Problem

Cause

Cure

The suction flow is

less than expected

Suction piping is too restrictive

Remove restriction

Discharge pressure is too high

Remove restriction

Motive fluid pressure is lower than required

Increase pressure

Suction liquid is much higher than ambient temperature

Lower temperature or size

larger jet pump

Suction piping leaks

Tighten fittings

Table 2

7.0 Disassembly-Reassembly

Do not proceed with removal of jet pump from connecting piping unless the jet pump has been

relieved of all pressure or vacuum, has been allowed to reach ambient temperature and has

been drained or purged of all fluids. Failure to follow these instructions may cause personal

injury or property damage.

The jet pump Models GL and GH are made up of two parts (see Figure 3), a nozzle (61) and a body

(11) which are held together by a straight right hand mechanical thread, closing the face seal between

these parts.

To disassemble the unit, first attach a short piece of pipe to the suction connection as a handle, then

grip the nozzle flats and rotate in a counterclockwise direction.

When ready to reassemble unit, be sure the seal face of the nozzle and body are free of foreign

material and raised metal due to nicks. A non-hardening pipe seal compound may be applied to the

threads to further promote sealing. Thread the body back on to the nozzle turning in a clockwise

direction.

8.0 Disposal at End of Useful Life

Penberthy Jet Pumps are used in a variety of fluid applications. By following the appropriate federal

and industry regulations, the user must determine the extent of preparation and treatment the Jet

Pump must incur before its disposal. A Material Safety Data Sheet (MSDS) may be required before

disposal services accept certain components.

Metal, glass and polymers should be recycled whenever possible. Refer to order and PV&C - Black

Mountain Material Specification sheets for materials of construction.

CAUTION

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

9.0 Telephone Assistance

If you are having difficulty with your Jet Pump, contact your local Penberthy distributor.

So that we may assist you more effectively, please have as much of the following information available

as possible when you call:

Model #

Name of the company from whom you purchased the Jet Pump

Invoice # and date

Process conditions (pressure, flow rates, tank shape, etc)

A brief description of the problem

Trouble shooting procedures that failed

If attempts to solve your problem fail, you may request to return your Jet Pump to the factory for

intensive testing. You must obtain a Return Authorization (R.A.) number from PV&C Black Mountain

before returning anything. Failure to do so will result in the unit being returned to you without being

tested, freight collect. To obtain an R.A. number, the following information (in addition to that above) is

needed:

Reason for return

Person to contact at your company

“Ship To” address

There is a minimum charge of $75.00 for evaluation of non-warranty units. You will be contacted

before any repairs are initiated should the cost exceed the minimum charge. If you return a unit under

warranty, but is not defective, the minimum charge will apply.

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

10.0 Exploded Parts Drawing

Figure 3

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

www.jrgjt.com

NORTHEAST CONTROLS INCORPORATED

TEL: 201-419-6111 ext. 23 for Venturi Group

[email protected]

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pentair Pompe à eau

Pentair

Pentair Hypro 9203 Series Guide de l'utilisateur

Pentair

Pentair WhisperFloXF Manuel utilisateur

Pentair

Pentair Jung Pumpen PSV-A/B 375 Manuel utilisateur

Pentair

Pentair JET Manuel utilisateur

Pentair

Pentair JUNG PUMPEN U 3 K/2 Manuel utilisateur

Pentair

Pentair MYERS E-10 Manuel

Pentair

Pentair ISO PRO Manuel utilisateur

Pentair

Pentair LINCOLN D Series Manuel utilisateur

Pentair

Pentair Fairbanks Nijhuis 5900 Series Manuel

Pentair

Pentair HYPRO 2100 Series Manuel d'utilisation et d'entretien

Pentair

Pentair myers aplex Series Manuel

Pentair

Pentair Myers MPN Series Manuel utilisateur

Pentair

Pentair FLOTEC SCM 4 PLUS 75/75 Manuel utilisateur

Pentair

Pentair Jung Pumpen WCFIX Plus Manuel utilisateur

Pentair

Pentair MYERS D65-16 Series Manuel utilisateur

Pentair

Pentair 1840 Manuel utilisateur

Pentair

Pentair Berkeley SS1XN-1/2 Manuel utilisateur

Pentair

Pentair Hydromatic HCU Series Manuel utilisateur

Pentair

Pentair JUNG PUMPEN MULTIFREE 25/2 AW Manuel utilisateur

Pentair

Pentair SHURFLO 4008 RV REVOLUTION Manuel utilisateur

Pentair

Pentair HYDROMATIC HYDR-O-RAIL SYSTEM Manuel

Pentair

Pentair Fairbanks Nijhuis 1500 Series Manuel utilisateur

Pentair

Pentair MYERS MS33PT Manuel utilisateur

Pentair

Pentair AERMOTOR SPCM Series Manuel du propriétaire

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur