PCB Piezotronics 480M122 Manuel utilisateur

Model 480M122

Battery-Powered Signal Conditioner

Installation and Operating Manual

For assistance with the operation of this product,

contact PCB Piezotronics, Inc.

Toll-free: 800-828-8840

24-hour SensorLine: 716-684-0001

Fax: 716-684-0987

E-mail: [email protected]

Web: www.pcb.com

The information contained in this document supersedes all similar information that

may be found elsewhere in this manual.

Service –Due to the sophisticated

nature of the sensors and associated

instrumentation provided by PCB

Piezotronics, user servicing or repair is

not recommended and, if attempted,

may void the factory warranty. Routine

maintenance, such as the cleaning of

electrical connectors, housings, and

mounting surfaces with solutions and

techniques that will not harm the

physical material of construction, is

acceptable. Caution should be observed

to ensure that liquids are not permitted

to migrate into devices that are not

hermetically sealed. Such devices

should only be wiped with a dampened

cloth and never submerged or have

liquids poured upon them.

Repair –In the event that equipment

becomes damaged or ceases to

operate, arrangements should be made

to return the equipment to PCB

Piezotronics for repair. User servicing or

repair is not recommended and, if

attempted, may void the factory

warranty.

Calibration –Routine calibration of

sensors and associated instrumentation

is recommended as this helps build

confidence in measurement accuracy

and acquired data. Equipment

calibration cycles are typically

established by the users own quality

regimen. When in doubt about a

calibration cycle, a good “rule of thumb”

is to recalibrate on an annual basis. It is

also good practice to recalibrate after

exposure to any severe temperature

extreme, shock, load, or other

environmental influence, or prior to any

critical test.

PCB Piezotronics maintains an ISO-

9001 certified metrology laboratory and

offers calibration services, which are

accredited by A2LA to ISO/IEC 17025,

with full traceability to SI through

N.I.S.T. In addition to the normally

supplied calibration, special testing is

also available, such as: sensitivity at

elevated or cryogenic temperatures,

phase response, extended high or low

frequency response, extended range,

leak testing, hydrostatic pressure

testing, and others. For information on

standard recalibration services or

special testing, contact your local PCB

Piezotronics distributor, sales

representative, or factory customer

service representative.

Returning Equipment –Following

these procedures will ensure that your

returned materials are handled in the

most expedient manner. Before

returning any equipment to PCB

Piezotronics, contact your local

distributor, sales representative, or

factory customer service representative

to obtain a Return Warranty, Service,

Repair, and Return Policies and

Instructions Materials Authorization

(RMA) Number. This RMA number

should be clearly marked on the outside

of all package(s) and on the packing

Service, Repair, and Return

Policies and Instructions

list(s) accompanying the shipment. A

detailed account of the nature of the

problem(s) being experienced with the

equipment should also be included

inside the package(s) containing any

returned materials.

A Purchase Order, included with the

returned materials, will expedite the

turn-around of serviced equipment. It is

recommended to include authorization

on the Purchase Order for PCB to

proceed with any repairs, as long as

they do not exceed 50% of the

replacement cost of the returned

item(s). PCB will provide a price

quotation or replacement

recommendation for any item whose

repair costs would exceed 50% of

replacement cost, or any item that is not

economically feasible to repair. For

routine calibration services, the

Purchase Order should include

authorization to proceed and return at

current pricing, which can be obtained

from a factory customer service

representative.

Contact Information –International

customers should direct all inquiries to

their local distributor or sales office. A

complete list of distributors and offices

can be found at www.pcb.com.

Customers within the United States may

contact their local sales representative

or a factory customer service

representative. A complete list of sales

representatives can be found at

www.pcb.com. Toll-free telephone

numbers for a factory customer service

representative, in the division

responsible for this product, can be

found on the title page at the front of this

manual. Our ship to address and

general contact numbers are:

PCB Piezotronics, Inc.

3425 Walden Ave.

Depew, NY14043 USA

Toll-free: (800) 828-8840

24-hour SensorLineSM: (716) 684-0001

Website: www.pcb.com

E-mail: [email protected]

PCB工业监视和测量设备 - 中国RoHS2公布表

PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table

部件名称

有害物质

铅(Pb)

汞

(Hg)

镉

(Cd)

六价铬(Cr(VI))

多溴联苯 (PBB)

多溴二苯醚(PBDE)

住房

PCB板

电气连接器

压电晶体

环氧

铁氟龙

电子

厚膜基板

电线

电缆

塑料

焊接

铜合金/黄铜

本表格依据 SJ/T 11364 的规定编制。

O：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

铅是欧洲RoHS指令2011/65/ EU附件三和附件四目前由于允许的豁免。

CHINA RoHS COMPLIANCE

DOCUMENT NUMBER: 21354

DOCUMENT REVISION: D

ECN: 46162

Component Name

Hazardous Substances

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Chromium VI

Compounds

(Cr(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl

Ethers (PBDE)

Housing

PCB Board

Electrical

Connectors

Piezoelectric

Crystals

Epoxy

Teflon

Electronics

Thick Film

Substrate

Wires

Cables

Plastic

Solder

Copper Alloy/Brass

This table is prepared in accordance with the provisions of SJ/T 11364.

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572.

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above

the limit requirement of GB/T 26572.

Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.

Model 482C02 / 480E09

Battery-Powered ICP®Signal Conditioners

Operating Manual with Enclosed Warranty Information

3425 Walden Avenue, Depew, New York 14043-2495

Phone (716) 684-0003

Fax (716) 684-3823

Toll Free Line 1-800-828-8840

MANUAL NUMBER: 19175

MANUAL REVISION: A

ECO: 50452

PAGE 2

MANUAL NUMBER: 19175

MANUAL REVISION: A

Table of Contents

Introduction....................................................................................................................... page 3

Description ....................................................................................................................... page 4

Operation.......................................................................................................................... page 5

Performance Limits .......................................................................................................... page 8

Battery Considerations..................................................................................................... page 8

Optional Power Connections............................................................................................ page 9

Warranty......................................................................................................................... page 10

Calibration & Service...................................................................................................... page 10

Return Procedure........................................................................................................... page 10

Total Customer Satisfaction ........................................................................................... page 11

PAGE 3

MANUAL NUMBER: 19175

MANUAL REVISION: A

Introduction

Model 480C02 & model 480E09 are rugged, portable, power sources for ICP® sensors. These models are nearly

identical except model 480C02 is unity gain 1:1 only with no adjustment, while model 480E09 has the additional

feature of 3-position gain adjustment (1/10/100). They are powered internally by three replaceable batteries and

provide constant current excitation to the charge amplifier within ICP® sensors (or to in-line and adaptor style

amplifiers) and decouples the sensor output signal from the power. Signal output is a high quality, voltage output

compatible with standard readout, recording or acquisition instruments.

Figure 1: Model 480C02 Signal Conditioner

Red (fault, electrical short)

Yellow

(fault, low battery)

Green (connected

& no fault)

EXT PWR –use with

488A03 AC Power Source

PAGE 4

MANUAL NUMBER: 19175

MANUAL REVISION: A

Figure 2: Model 480E09 Signal Conditioner

Description

Models 480C02 / 480E09 contain three, PP3 size, 9 volt batteries connected in series to provide DC power to

internal electronics which provide regulation for approximately 2.6 mA of constant current power. Connections

include two BNC jacks, one for Sensor (ICP®power/input) and one for Scope (output to scope, data recorder, or

DAQ). The front panel meter indicates the voltage output when connected to a sensor and is color coded for

various fault conditions, shown in Figure 1 & 2. Optional connections include sockets for EXT PWR and BATT

CHG. A central, three-position rocker switch allows off, on and momentary battery test functionality.

Model 480E09 has the additional 3-position gain adjustment that multiplies the signal output through the SCOPE

connection. It has 2 additional settings beyond the 480C02, 10x and 100x, shown in Figure 2.

Red (fault, electrical short)

Yellow (fault, low battery)

Green (connected & no fault)

EXT PWR –use with

488A03 AC Power Source

Gain Select –Rotary Switch

PAGE 5

MANUAL NUMBER: 19175

MANUAL REVISION: A

Operation

Internal electronics include a capacitor and resistor that decouples the sensor output signal from the DC power.

With no sensor connected, move power switch to “ON” position. The front panel voltmeter measures the battery

voltage with full scale set at 27 volts (+27 volts for new batteries), see Figure 1. When an ICP® sensor is

connector to the input “XDCR” jack, the meter will indicate approximately mid-scale (+11 volts nominal) if the

sensor’s internal amplifier and cables are functioning properly without damage. Some sensors use a 5 volt

excitation and in this case the meter will read at the lower edge of the green region.

Figure 3: Models 480C02 / 480E09 Signal Conditioner Schematic

480E09 Only

2.6 mA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PCB Piezotronics Électricité industrielle

PCB Piezotronics

PCB Piezotronics T356M98 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics M1381-001-01A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics IMI SENSORS M635A01 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics IMI SENSORS 691B35 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 1403-14A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 123B Manuel utilisateur

PCB Piezotronics

PCB Piezotronics ICP RH204C Manuel utilisateur

PCB Piezotronics

PCB Piezotronics W138A01/038CY030AC Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 202M44/050AD Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 340A66 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics JM353B17 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 352B10 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 478B05 Manuel utilisateur

Manuels Électricité industrielle populaires d'autres marques

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Manuel technique

Abtech

Abtech HVJB Series Mode d’emploi

Murata

Murata GRM0335C1H8R1DA01 Series Manuel utilisateur

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Manuel utilisateur

Eaton

Eaton Ulusoy HMH24-04 Manuel utilisateur

Newlong

Newlong NP-7H Manuel utilisateur

Murata

Murata GJM0335C1E4R4BB01 Series Manuel utilisateur

Stahl

Stahl 8575/12 Manuel utilisateur

SI Pegasus Manuel utilisateur

Murata

Murata GRM1555C1H2R7CA01 Seies Manuel utilisateur

Murata

Murata GRM0225C1E6R4BA03 Series Manuel utilisateur

Cooper Power Systems

Cooper Power Systems VXE15 Manuel utilisateur

S&C

S&C Vista SD Manuel utilisateur

Murata

Murata GRM0335C2A7R3CA01 Series Manuel utilisateur

Siemens

Siemens 3VA9988-0BM10 Manuel utilisateur

Siemens

Siemens SITRANS LVS100 Manuel utilisateur

Murata

Murata GRM32ER60G227ME05 Series Manuel utilisateur

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Manuel utilisateur