Patton electronics CopperLink 2160 Series Manuel utilisateur

CopperLink™ Model 2160 Series

Long Range Ethernet Extender

Quick Start Guide

Part Number: 07M2160-QS, Rev. B

Revised: February 24, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2Model 2160 Series Quick Start Guide

1.0 Connect the power and ports

1. Connect the power adapter to the port labeled DC 9V on the rear panel of the Model 2160.

2. Connect the Ethernet cable to the MGMT port.

Note The Model 2160 supports auto-MDX/MDIX switching hub so you may use a straight-through or cross-

over Ethernet cable.

3. Connect the phone cable to the Model 2160 and the other side of phone cable to wall jack.

4. Connect the power adapter to power source.

5. Turn on the PC to configure the Model 2160.

• The Model 2160 contains no user serviceable parts. The equip-

ment shall be returned to Patton Electronics for repairs, or

repaired by qualified service personnel. Opening the Model

2160 case will void the warranty.

• Mains Voltage: Do not open the case the when the power cord

is attached. Line voltages are present within the power supply

when the power cords are connected. The mains outlet that is

utilized to power the device shall be within 10 feet (3 meters)

of the device, shall be easily accessible, and protected by a cir-

cuit breaker.

• For AC powered units, ensure that the power cable used meets

all applicable standards for the country in which it is to be

installed, and that it is connected to a wall outlet which has

earth ground.

• Hazardous network voltages are present in WAN ports

regardless of whether power to the Model 2160 is ON or OFF.

To avoid electric shock, use caution when near WAN ports.

When detaching the cables, detach the end away from the

Model 2160 first.

•

Do not work on the system or connect or disconnect cables dur-

ing periods of lightning activity.

To avoid possible damage to this Model 2160, do not turn on the modem

before connecting the cables.

WARNING

Model 2160 Series Quick Start Guide 3

Figure 1. Model 2160 Connection Diagram

2.0 Choose a configuration method and log in

There are three methods to configure the Model 2160: serial console, Telnet and Web Browser. You must choose

one method to configure the Model 2160.

2.1 Web configuration

Make sure that an Ethernet Adapter has been installed in the PC or NB you will use to configure the modem.

TCP/IP protocol is necessary for web configuration, so check if the TCP/IP protocol has been installed.

The Model 2160 provides a browser interface that allows you to configure and manage the Model 2160. After

you set up the IP address for the Model 2160, you can access the Web interface applications directly in your

browser by entering the IP address of the Model 2160. You can then use your Web browser to list and manage

configuration parameters from a PC.

Web Configuration requires Internet Explorer 5.0 or later or Netscape Navigator 6.0 and later versions. The rec-

ommended screen resolution is 1024 by 768 pixels.

DC 9V CONSOLE

RST

MGMT LINE

LAN

Desktop PC Laptop computer

LAN

Printer

Switch

Notebook

Desktop PC

ServerRAID Drive

WAP

4Model 2160 Series Quick Start Guide

2.2 Serial console configuration

For configuring the Model 2160 through the serial console, connect a terminal or a PC equipped with a terminal-

emulation program (such as Hyper Terminal) to the Model 2160's console port.

Use the supplied serial cable (RJ-45 to DB9F) to connect the Model 2160 to a PC. After marking the connection,

configure the terminal-emulation program using the following parameters: 9600 bps , 8 data bits , no parity and

1 stop bit.

2.3 Telnet configuration

Make sure that an Ethernet Adapter has been installed in the PC or NB you will use to configure the Ethernet

extender. The Model 2160 also supports Telnet for remote configuration. The command is “telnet 192.168.1.1” .

For logging into the system through a Telnet connection, “admin” for username and “admin” for password.

The default IP address is 192.168.1.1. You may change the IP address for your application.

3.0 Additional information

For detailed information about installing, configuring, operating, and troubleshooting your Model 2160, refer to

the Model 2160 User Manual available online at www.patton.com/manuals/2160.pdf.

A.0 Compliance Information

A.1 Compliance

EMC:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

A.2 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

Model 2160 Series Quick Start Guide 5

A.3 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con-

firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications

were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certified connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certified equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

A.4 CE Declaration of Conformity

We certify that the apparatus described above conforms to the requirements of Council Directive 2004/108/EC

on the approximation of the laws of the member states relating to electromagnetic compatibility; and Council

Directive 2006/95/EC on the approximation of the laws of the member states relating to electrical equipment

designed for use within certain voltage limits.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above

directive is indicated by the CE sign on the device.

A.5 Authorized European Representative

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road

Watchfield,

Swindon, Wilts SN6 8TD, UK

6Model 2160 Series Quick Start Guide

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term CopperLink is a trademark of Patton Electronics Company. All other trademarks presented in this docu-

ment are the property of their respective owners.

Patton support headquarters in the USA

•

Online support: Available at www.patton.com

•

E-mail support: E-mail sent to support@patton.com will be answered within 1 business day

•

Telephone support: Standard telephone support is available five days a week—from 8:00 am to

5:00 pm EST (1300 to 2200 UTC/GMT)—by calling +1 (301) 975-1007

•

Support via VoIP: Contact Patton free of charge by using a VoIP ISP phone to call sip:[email protected]

•

Fax: +1 (253) 663-5693

Alternate Patton support for Europe, Middle East, and Africa (EMEA)

•

Telephone support: Standard telephone support is available five days a week—from 8:00 am to

5:00 pm CET (0900 to 1800 UTC/GMT)—by calling +41 (0)31 985 25 55

•

Fax: +41 (0)31 985 25 26

Note For additional service and support information, refer to the “Contacting Patton for assistance” chapter

of the CopperLink 2160 User Manual available online at www.patton.com/manuals/2160.pdf.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the Model 2160 User Manual available online at

www.patton.com/manuals/2160.pdf.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

Model 2160 Series Quick Start Guide 7

NOTES

____________________________________________________________________

8Model 2160 Series Quick Start Guide

NOTES

____________________________________________________________________

Autres manuels pour CopperLink 2160 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Patton electronics Extenseur

Patton electronics

Patton electronics SmartNode 2292 Manuel utilisateur

Patton electronics

Patton electronics EnviroNet Ethernet Extenders Manuel utilisateur

Patton electronics

Patton electronics 1173R Manuel utilisateur

Patton electronics

Patton electronics EnviroNET EHA2172 Manuel utilisateur

Patton electronics

Patton electronics CopperLink 2155 Manuel utilisateur

Patton electronics

Patton electronics CopperLink 2160 Series Manuel utilisateur

Patton electronics

Patton electronics CopperLink 2172R Manuel utilisateur

Patton electronics

Patton electronics CopperLink 2172R Manuel utilisateur

Patton electronics

Patton electronics CopperLink 2168 Manuel utilisateur

Patton electronics

Patton electronics CopperLink Ethernet Booster 2110 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 2294 Manuel utilisateur

Patton electronics

Patton electronics CopperLink 2158 Manuel utilisateur

Patton electronics

Patton electronics CopperLINK 2173 Manuel utilisateur

Patton electronics

Patton electronics 2113 Manuel utilisateur

Patton electronics

Patton electronics CopperLink Ethernet Extenders 2158A Manuel utilisateur

Patton electronics

Patton electronics CopperLink 2160 Series Manuel utilisateur

Patton electronics

Patton electronics COPPERLINK 2150 Manuel utilisateur

Patton electronics

Patton electronics CopperLink 07M2160-GS Manuel utilisateur

Patton electronics

Patton electronics CopperLINK 2158B Manuel utilisateur

Patton electronics

Patton electronics Industrial Ethernet Extender with LCD Interface... Mode d’emploi

Patton electronics

Patton electronics COPPERLINK 2151 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 2290 Series Manuel utilisateur

Patton electronics

Patton electronics CopperLINK 2173 Manuel utilisateur

Patton electronics

Patton electronics 2173R Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur