Patton electronics Smart-DTA Manuel utilisateur

Smart-DTA™

ISDN VoIP Telephone Adapter

Quick Start Guide

Important

—

This is a Class B device and is intended for use in a light industrial or residential

environment. It is not intended nor approved for use in an industrial environment

Caution

—This device is not intended nor approved for connection to the public ISDN telecommuni-

cation network.

Attention

—Ce dispositif n'est pas prévu ni approuvé pour le raccordement au réseau de

télécommunication public le RNIS.

Vorsicht

—Dieses Gerät ist nicht für Anschaltung an das öffentlich ISDN

Telekommunikationsnetz genehmigt.

Precaución

—Este dispositivo no está previsto ni se ha aprobado para la conexión a la red de

telecomunicaciones pública ISDN.

Attenzione

—Questo dispositivo non è inteso né non approvato per collegamento alla rete di

telecomunicazione pubblica ISDN.

Document Number: 13228U7-002 Rev. B

Part Number: 07MSDTA1-QS

Revised: October 26, 2007

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

Smart-DTA Quick Start Guide

1.0 Power up the Smart-DTA

Connect the Smart-DTA to a power source using the included power supply and cable.

When the

Power

LED stops blinking and remains lit, the Smart-DTA is ready to conﬁgure.

• The Smart-DTA contains no user serviceable parts. The equipment

shall be returned to Patton Electronics for repairs, or repaired by

qualiﬁed service personnel.

• Mains Voltage: Do not open the case the power cord is attached. The

external power adaptor shall be a listed limited power source that

incorporates a disconnect device and shall be positioned within easy

reach of the operator. The mains outlet shall be within 10 feet (3

meters) of the device, shall be easily accessible, and protected by a

circuit breaker.

• The Smart-DTA is not shipped with power cables. For AC powered

units, ensure that the power cable used meets all applicable stan-

dards for the country in which it is to be installed, and that it is con-

nected to a wall outlet which has earth ground.

• Hazardous network voltages are present in WAN ports regardless of

whether power to the Smart-DTA is ON or OFF. To avoid electric

shock, use caution when near WAN ports. when detaching the cables,

detach the end away from the Smart-DTA ﬁrst.

• Do not work on the system or connect or disconnect cables during

periods of lightning activity.

The terminal block header to which the wires are secured provides the disconnect for

the Smart-DTA. Take proper measures to ensure that it is not permanently fastened to

the receptacle mounted on the chassis.

WARNING

CAUTION

Smart-DTA Quick Start Guide

2.0 Connect the Smart-DTA to your local network

You must connect the Smart-DTA to an IP network that provides a DHCP server. Using the included black Ethernet

cable, connect the Smart-DTA RJ-45 Ethernet WAN port, labeled

ETH

(see

ﬁgure 1

), to an Ethernet hub or switch

on the same network as your PC. The Ethernet WAN interface is conﬁgured as a DHCP client.

Figure 1.

Connecting the Smart-DTA to the network via a hub or switch

DHCP

Server

Ethernet Hub

or Switch

Smart-DTA

ETH

port

Smart-DTA Quick Start Guide

3.0 Connect the Smart-DTA to an ISDN phone

Using a straight-though cable, terminated with RJ-45 connectors, connect the BRI port of your Smart-DTA

to the S/T port of your ISDN phone, as shown below:

Note: Other pins are not used.

ISDN

Phone

RJ-45, male RJ-45, male

Smart-DTA Quick Start Guide

4.0 Start the SmartNode Discovery Tool

Insert the CD included with your Smart-DTA into the CD drive on your PC.

Copy the ﬁle named

SNDiscovery.exe

from the CD to your PC.

At your PC, double-click the

SNDiscovery.exe

ﬁle name to activate the tool. The SmartNode Discovery Tool

window will display the IP Address, MAC Address, Device Type (model number) and Build (software

release) of your Smart-DTA.

If your Smart-DTA does not appear:

• Make sure the Smart-DTA and your PC are on the same routed subnet

• Make sure any ﬁrewall programs on your PC are disabled

5.0 Access the Web Browser (GUI) Interface

In the SmartNode Discovery Tool window, select the line that displays the IP address of your Smart-DTA.

Figure 2.

SmartNode Discovery Tool window

Smart-DTA Quick Start Guide

Right-click the selected line, and select

Webbrowser

. The Login window will display.

Figure 3.

Enter the username

administrator

. Do not enter a password. Instead simply click OK. Your web browser will

display the Smart-DTA home page.

Figure 4.

Smart-DTA home page

Smart-DTA Quick Start Guide

6.0 Conﬁguring your Smart-DTA

Once you have logged in you can use the browser-based graphical user interface (GUI) to conﬁgure and manage

your S-DTA. The Smart-DTA home page displays three

Immediate Actions

buttons that allow you to store the cur-

rent conﬁguration state, reload the device, and restore to factory defaults. The home page also displays certain

basic system information. You can always return to the home page by clicking

Home

in the navigation bar.

The GUI consists of the following main elements:

•

The “Navigation Bar” on the left edge presents you with a menu listing giving access to the various conﬁgura-

tion and status pages of the Smart-DTA.

•

At the top of the page you see the “Current System Path” which displays the location and element currently

presented in the main area.

•

The rest of the page displays the conﬁguration and status information for the different features of

the Smart-DTA.

7.0 Additional Information

Refer to the

Smart-DTA Getting Started Guide

located on the CD-ROM shipped with your Smart-DTA device and

available online at

www.patton.com/manuals.

For detailed information about:

•

Installing, conﬁguring, operating, and troubleshooting.

•

Warranty, trademark & compliance

The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients.

Whenever you modify the conﬁguration your Smart-DTA, immediately applies your

changes.Howver, your new settings ARE NOT PERMANENTLY SAVED (in non-volatile

memory [RAM]). To survive power failure or manual reload you must store your new

settings in non-volatile memory. To save your changes: return to the home page and

press the Save Current Conﬁguration button.

IMPORTANT

Smart-DTA Quick Start Guide

A.0 Customer and Technical Support

Toll-Free VoIP support: call

sip:[email protected]

with a VoIP SIP client

Online support: www

.patton.com

E-mail support:

[email protected]

—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax:

+1 (253) 663-5693

(USA)

or +41 (0)31 985 25 26 (

Switzerland)

B.0 Appendix—Factory default IP addresses

Factory default IP addresses and netmask conﬁguration.

IP Address Network mask

WAN interface Ethernet 0 (0/0)

DHCP Client n/a

LAN interface Ethernet 1 (0/1)

192.168.1.1 255.255.255.0

DHCP server address range (LAN)

192.168.1.10-192.168.1.99 255.255.255.0

Smart-DTA Quick Start Guide

C.0 Compliance Information

C.1 Compliance

EMC Compliance:

•

FCC Part 15, Class B

•

EN55022, Class B

•

EN55024

Safety Compliance:

•

IEC 60950-1

•

EN60950-1

C.2 Radio and TV interference

The Smart-DTA router generates and uses radio frequency energy, and if not installed and used properly—that

is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television

reception. The Smart-DTA router have been tested and found to comply with the limits for a Class B computing

device in accordance with speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide rea-

sonable protection from such interference in a commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the Smart-DTA router does cause interference to radio or

television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct

the interference by one or more of the following measures: moving the computing equipment away from the

receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet

(such that the computing equipment and receiver are on different branches).

C.3 CE Declaration of Conformity

We certify that the apparatus described above conforms to the requirements of Council Directive 2004/108/EC

on the approximation of the laws of the member states relating to electromagnetic compatibility; and Council

Directive 2006/95/EC on the approximation of the laws of the member states relating to electrical equipment

designed for use within certain voltage limits.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above

directive is indicated by the CE sign on the device.

C.4 Authorized European Representative

D R M Green, European Compliance Services Limited.

Oakdene House, Oak Road , Watchﬁeld, Swindon, Wilts SN6 8TD, UK

Smart-DTA Quick Start Guide

NOTES

____________________________________________________________________

Autres manuels pour Smart-DTA

Table des matières

Autres manuels Patton electronics Adaptateur

Patton electronics

Patton electronics 14TB Manuel utilisateur

Patton electronics

Patton electronics S-WTA Manuel utilisateur

Patton electronics

Patton electronics 464RC Manuel utilisateur

Patton electronics

Patton electronics 3P-MF Manuel utilisateur

Patton electronics

Patton electronics S-DTA Manuel utilisateur

Patton electronics

Patton electronics Patton SmartLink M-ATA Manuel utilisateur

Patton electronics

Patton electronics 504 Manuel utilisateur

Patton electronics

Patton electronics 400 Manuel utilisateur

Patton electronics

Patton electronics 505M-CHC Manuel utilisateur

Patton electronics

Patton electronics Smart-DTA Manuel utilisateur

Patton electronics

Patton electronics 460 SERIES Manuel utilisateur

Patton electronics

Patton electronics 465F Manuel utilisateur

Patton electronics

Patton electronics 3004 Manuel utilisateur

Patton electronics

Patton electronics 405 Manuel utilisateur

Patton electronics

Patton electronics 2003 Manuel utilisateur

Patton electronics

Patton electronics 460 SERIES Manuel utilisateur

Patton electronics

Patton electronics SmartLink M-ATA Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur