Page 8 of 16 HPS 845 R.7 COD:00-99-0I84505 (000)
•Ignition Key ON, front doors closed and alarm disarmed, push the anti theft button for about
10 seconds, the LED start to flash slowly.
•Release the button before the LED stops to flash.
If the function is enabled -> 1 blinkers flash– 1 beep – 1 LED flash
If the function is disabled -> 2 blinkers flashes – 2 beeps – 2 LED flashes
Every time that the ignition key is turned ON, the LED flash 2 times slowly for about 40 seconds, to
show that the function is ON.
P
PR
RE
E
V
VA
AL
LE
ET
T
F
FU
UN
NC
CT
TI
IO
ON
N
This function permit to disable the anti aggression and anti theft functions (if set), keeping ON all
the other functions of the alarm.
Activation of the PRE-VALET function:
•Ignition key ON, front doors opened and alarm disarmed, push the anti theft button for about
10 seconds, the LED start to flash slowly.
•Release the button before the LED stops to flash.
If the function is enabled -> 1 blinkers flash– 1 beep – 1 LED flash
If the function is disabled -> 2 blinkers flashes – 2 beeps – 2 LED flashes
U
US
SE
E
O
OF
F
T
TH
HE
E
E
EM
ME
ER
RG
GE
EN
NC
CY
Y
U
UN
NL
LO
OC
CK
KI
IN
NG
G
P
PI
IN
N
C
CO
OD
DE
E
WARNING: If the n°25 function has been activated, the procedure must be performed
with the brake pedal or the parking brake and driver DOOR OPEN.
Do not use the handbrake with pulled pedal and vice versa.
To be used when the remote controls are lost or no longer operating when the alarm system is still
armed.
The code is always made of 3 digits (factory setting: 1-2-3). This code should be composed (when the
alarm is armed) via the ignition key as per the procedure detailed below:
1. Turn the ignition key ON/OFF as many times as per the first digit (e.g. 1 in case of factory setting)
The LED is illuminated while composing the pin code and the horn or the siren sounds.
Wait until the LED extinguishes.
2. Turn the ignition key ON/OFF as many times as per the second digit (e.g. 2 in case of factory
setting)
3. Wait until the LED extinguishes.
4. Turn the ignition key ON/OFF as many times as per the third digit (e.g. 3 in case of factory
setting)
If you succeed, the alarm system will disarm after the third digit.
C
CH
HA
AN
NG
GE
E
O
OF
F
T
TH
HE
E
R
RE
EL
LE
EA
AS
SE
E
P
PI
IN
N
C
CO
OD
DE
E
You may customize the factory pre-set release pin code (1-2-3) just following the herewith procedure,
alarm disarmed:
Through the ignition key compose the old secret code as described in the previous paragraph.
Wait for quick LED flashes of confirmation that the old code of unblocking is correct, then
1. Turn the ignition key ON/OFF as many times as per the first value to be modified.
The LED will illuminate during the composition of the secret code.
Wait that the LED on the dashboard extinguishes.
2. Turn the ignition key ON/OFF as many times as per the second value to be modified.
Wait that the LED on the dashboard extinguishes.
3. Turn the ignition key ON/OFF as many times as per the third value to be modified.
Wait that the LED on the dashboard extinguishes
If you succeed, the quick flashing of the LED on the dashboard confirms that the new secret code has
successfully substituted the old one.
THE NEW PIN CODE WAS STORED AND HAS SUBSTITUITE THE OLD ONE
INSERT HERE THE NEW PIN CODE _______________
Installer section
G
GE
EN
NE
ER
RA
AL
L
C
CO
ON
NN
NE
EC
CT
TI
IO
ON
N
D
DI
IA
AG
GR
RA
AM
M
H
HP
PS
S
5
5
There is a specific fitting instruction for every vehicle that is wrote into the vehicle compatible list.
