PASCO CI-6460 Manuel utilisateur
Instruction Manual
Manual No. 012-08713A
Force Sensor
Balance Stand
Model No. CI-6460
Balance Stand Model No. CI-6460
2®
Table of Contents
Equipment List........................................................... 3
Introduction ............................................................. 4
Basic Setup.............................................................. 4
Setup Options ........................................................... 5
Suggested Experiments ............................................. 7-10
Experiment 1: Exploring the Relationship between Buoyancy and Archimedes’ Principle ..... 7-8
Experiment 2: Exploring the Relationship Between Normal Force and Angle....................... 9-10
Appendix A: DataStudio Setup Instructions .........................11
Appendix B: Creating Equations in DataStudio ......................12
Appendix C: Technical Support ....................................... 13
Appendix D: Copyright and Warranty Information .................. 13
Model No. CI-6460 Force Sensor Balance Stand
3
®
Force Sensor Balance Stand
Model No. CI-6460
Equipment List
*Use Replacement Model Numbers to expedite replacement orders.
Included Equipment Replacement
Model Number*
1. Force Sensor Balance Stand CI-6460
2. Balance Pan 648-08700
Additional Equipment Recommended Replacement
Model Number*
Any PASCO
ScienceWorkshop
®or PASPORT™interface Various*,**
(See PASCO catalog.)
Force Sensors CI-6746 or CI-6537 or
PS-2104
DataStudio®software See PASCO catalog.
Mass Set See PASCO catalog
A computer NA
1
2
*PASPORT sensors require a PASPORT computer interface.
**ScienceWorkshop sensors require a ScienceWorkshop interface. (Do not mix
PASPORT and ScienceWorkshop sensors in the same experiment.)
Force Sensor Balance Stand Model No. CI-6460
4
®
Introduction
The Force Sensor Balance Stand is designed to allow the use of a PASCO Force Sensor as a
balance. The sensor is mounted on a bracket and the circular balance pan is screwed directly
into the Force Sensor in place of the hook. When used with DataStudio, both weight and
mass can be determined with a Force Sensor and a stand. Both ScienceWorkshop and
PASPORT Force Sensors can be used with the Force Sensor Balance Stand.
The Force Sensor Balance Stand is ideal for usage in experiments exploring buoyancy,
gravitational, and normal forces.
Basic Setup:
1. Using the screws provided with the Force Sensor, mount the sensor on the balance stand. See
Figure 1 for the appropriate mounting positions.
2. Unscrew the hook from the top of the Force Sensor. Screw the balance pan into the
threaded hole on the top of the Force Sensor.
3. Connect the Force Sensor to either a ScienceWorkshop or PASPORT interface. (For
software setup, see Appendix A.)
4. Place an object on the balance pan. Try to center the object for best results.
5. In DataStudio, click the Start button to display the weight of the object.
6. Use the calculator in DataStudio to create the following equation, which displays the mass
in kg:
Figure 1: Front view of Force
Sensor Balance Stand
Attach the
Economy Force
Sensor and
PASPORT
Force Sensor
here.
Use these two
holes to attach the
ScienceWorkshop
Force Sensor.
Use this hole to
store the balance
pan.
mass
F
orce
9.81
----------------=
Model No. CI-6460 Force Sensor Balance Stand
5
®
Setup Options
a) Mounting a Force Sensor
The Force Sensor Balance Stand can be used with three different PASCO force sensors (See
Figures 2a-2c below.)
b) Mounting both a Force and Acceleration Sensor
In addition, an acceleration sensor can be mounted to the stand to measure the angle of
incline. Depending on the force sensor used, the mounting position will vary. To mount an
acceleration sensor, use the bracket and screws provided with the acceleration sensor.
Figure 2a: Setup with a
PASPORT Force
Sensor (PS-2104)
Figure 2b: Setup with a
ScienceWorkshop
Force Sensor (CI-6537)
Figure 2c: Setup with
an Economy Force
Sensor (CI-6746)
3a) front view
bracket
3b) side view
Figure 3a-3b: Setup with a PASPORT Force Sensor (PS-2104) and Acceleration
Sensor (PS-2118)
Force Sensor Balance Stand Model No. CI-6460
6
®
Hold the bracket against the side hole in the Force Sensor Stand. Insert a screw into the back
of the Acceleration Sensor and mount to the back of the stand. Insert another screw into the
bottom of the Acceleration Sensor to hold the sensor in place.
Note: If you are mounting a CI-6537 Force Sensor, mount the metal bracket to the front of
the Force Sensor Stand, as shown in Figure 5.
4a) front view 4b) side view
Figure 4a-4b: Setup with a
ScienceWorkshop
CI-6746 Economy Force and CI-6558
Acceleration Sensor
Figure 5: Setup with a CI-6537
ScienceWorkshop
Force Sensor and
CI-6558 Acceleration Sensor:
bracket
Model No. CI-6460 Force Sensor Balance Stand
7
®
Experiment 1: Exploring the Buoyancy Force and
Archimedes’ Principle
Procedure:
1. Mount a Force Sensor to the Force Sensor Balance Stand (see page 5).
2. Screw the Balance Pan into the Force Sensor.
3. Place the stand on a laboratory jack.
4. Connect the Force Sensor to a computer interface (For
DataStudio Setup instructions, see Appendix A.)
To avoid the risk of electric shock, keep water and
fluids away from sensors, power sources, computers, and
electrical apparatus. Observe standard electrical safety
precautions in your classroom.
5. Fill the beaker with the desired amount of water.
6. Place the beaker on the Balance Stand; then zero the
Force Sensor by pressing the Tare button.
7. Hang another Force Sensor directly above the beaker, as shown in Figure 1-1.
8. Choose a metal cylinder that will fit the beaker.
9. Use the Force Sensor Balance Stand to measure the weight of the cylinder.
10. With thread, hang the cylinder from the upper force sensor.
11. In DataStudio, create a graph which displays the following:
a) Force measured by the upper sensor (apparent weight)
Equipment Required:
Force Sensors (CI-6537, CI-6746,
PS-2104)) Computer interface
Force Sensor Balance Stand
(CI-6460) Two Stainless steel rods (ME-8736 or
ME-8738 or ME-8741)
Large Rod Base (ME-8735) Multi-Clamp (SE-9442),
Beaker (SE-7287 or 7288) Density Set (ME-8569)
Laboratory Jack (SE-9372 or SE-
9373 or SE-9374) String
Figure 1-1:
Experiment Setup
Force Sensor Balance Stand Model No. CI-6460
8
®
b) Force measured by the lower sensor (buoyancy force)
c) Weight of the cylinder
12. In DataStudio, click the Start button to begin data collection.
13. Use the lab jack to raise the beaker until the cylinder is fully submerged in the water.
14. To end data collection, click the Stop button in DataStudio.
Analysis:
1. What happens to the apparent weight as the cylinder is submerged? Explain.
2. What happens to the buoyancy force as the cylinder is submerged? Explain.
3. How are the apparent weight, buoyancy force, and cylinder weight related to one another?
Explain.
Sample Data with a PASPORT Force Sensor
Model No. CI-6460 Force Sensor Balance Stand
9
®
Experiment 2: Exploring the Relationship Between the
Normal Force and Angle
Purpose:
To investigate the relationship between the normal force and the track angle.
Procedure:
1. Attach a Force and Acceleration Sensor to the Balance
Stand by following the instructions in the Setup Options
section (pages 5-6).
2. Plug each sensor into a computer interface. (For more
information, see Appendix A).
3. Place the stand in the middle of the Dynamics Track.
4. Place the 500 g mass on the pan of the stand. Use a small
piece of tape under the mass to secure it to the stand.
5. In DataStudio, create a calculation for the angle:
or
6. In DataStudio, create a calculation for the normal force:
Equipment Required:
Force Sensor Balance Stand (CI-6460) Force Sensor (CI-6537, CI-6746, or
PS-2104)
Acceleration Sensor (CI-6558, or
PS-2118 or PS-2119) Dynamics Track (ME-6958) or flat
board
Computer interface DataStudio software
500 g mass (SE-8759)
Figure 2-1:Experiment
Setup
acceleration parallel to inclined plane
acceleration perpendicular to inclined plane
angle=arctan
acceleration parallel to the inclined plane
9.81 m/s2
angle=arcsin
normal force = weight*cos(angle)
Table des matières
Autres manuels PASCO Accessoires
PASCO
PASCO PS-3236 Mode d’emploi
PASCO
PASCO PS-3209 Manuel utilisateur
PASCO
PASCO PS-3217 Mode d’emploi
PASCO
PASCO PS-3208 Mode d’emploi
PASCO
PASCO PS-3517 Manuel utilisateur
PASCO
PASCO PasPort PS-2102 Manuel utilisateur
PASCO
PASCO PS-3218 Manuel utilisateur
PASCO
PASCO PS-3221 Manuel utilisateur
PASCO
PASCO PS-3219 Manuel utilisateur
PASCO
PASCO Pasport PS-2197 Manuel utilisateur
PASCO
PASCO CI-6538 Manuel utilisateur
PASCO
PASCO PASPORT PS-2104 Manuel utilisateur
PASCO
PASCO Physical Pendulum Accessory Manuel utilisateur
PASCO
PASCO PS-3248 Manuel utilisateur
PASCO
PASCO CI-6537 Manuel utilisateur
PASCO
PASCO PS-3224 Manuel utilisateur
PASCO
PASCO PS-3236 Manuel utilisateur
PASCO
PASCO PS-3202 Manuel utilisateur
PASCO
PASCO PASPORT PS-2177 Manuel utilisateur
PASCO
PASCO CI-6504A Manuel utilisateur
