ParTech MIGRO ARAY Mode d’emploi
Instruction manual and datasheet
CULTIVATING
HAPPINESS
Follow us @migrolight
www.migrolight.com
STOP - Please read all these instructions carefully especially the safety
section before unboxing and assembling
Contents
●Safety
●System hardware overview
●Assembly instructions
Rev. A
16-07-20
●How to optimise your grow light setup
●Technical specifications
●Maintenance
●Contact for technical support and frequently asked questions
Safety
Please read this manual thoroughly before assembling and installing the MIGRO
grow light system
Please retain this manual for reference for the lifetime for the product
The MIGRO system limits the voltage in the grow room to 96Vdc
and has built in protection for overcurrent, shorts or overheating.
However, to minimise any remaining risk please switch the power
off while installing and adjusting the MIGRO system.
If the mains plug needs to be changed to suit your power socket
only a qualified person should carry out this work, in accordance
with your local codes.
The MIGRO system will operate on a supply voltage ranging from 100V to 277V AC
and from 50 to 60Hz frequency. Any other supply voltage will damage the
lighting system.
The grow light and the cabling from the LED driver to the grow light is IP66 rated
and can be used in a wet area. The mains power plug is not IP rated for a wet area
and should be located in a dry area outside of the grow room. If the cable
insulation or glands are damaged switch off the system immediately and return
to us for repair.
The MIGRO grow light has a highly efficient and passive cooling
heatsink. In order to function correctly air must be able to flow
freely across the fins of the heatsink. Do not cover the grow light
and restrict the airflow across the heatsink under any
circumstances. This will result in heat build up which may
damage the grow light and/or cause a fire.
Do not put the grow light down on any surface when the light is on. The light
intensity and radiated heat may damage the surface.
By Partech LED Ltd
www.migrolight.com
2
The light intensity from each MIGRO grow light is very high. If
you look directly at the light source from less than 20cm or 9”
away the intensity is equivalent to the sun. To protect your eyes
do not look directly at the light source when less than 60cm or
2 feet away.
Setup instructions
Connect the LED
bars together with
the connector
brackets provided.
Cantre the bracket
along the length of
the LED bar (line it
up with the Cable
gland)
Attach the cable grip to each
power cable just above the
cable splitter. One the cable
grip is attached to the cable
then attach the ratchet
hanger to the cable grip
By Partech LED Ltd
www.migrolight.com
3
Hang the light in the tent
from the horizontal bars on
the top of the tent. Connect
the output cable from the
LED driver to the LED bar
cable and power on.
The ARAY 120W will rotate in
the grow area on its single
hanger
It’s ok : )
The light spread is even at
any
angle of rotation
Optimum hanging height
20cm/8”
16cm/6”
By Partech LED Ltd
www.migrolight.com
4
How much light plants need for
maximum yield
To optimise your grow it is recommended that your plants receive
500-1,000 µmols of PAR light for every m² (PPFD). Less than this and
growth rates and yield will be low.
.
Growth rates at higher PPFD levels do not justify the extra energy cost
and heat output and the plants require additional CO₂ to utilise the high
PAR intensity
Light Intensity PAR charts
By Partech LED Ltd
www.migrolight.com
5
Table des matières
Autres manuels ParTech Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
