PARRY MWBT Manuel utilisateur
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 1 of 15
www.parry.co.uk
INSTRUCTIONS
MODEL: MWBT
SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS
OPERATION INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
WIRING DIAGRAM
EXPLODED VIEW / PARTS LIST
WARRANTY INFORMATION
DISPOSAL INFORMATION
Customer Information
MODEL NUMBER:
______________________
SERIAL NUMBER:
______________________
PURCHASE DATE:
______________________
DISTRIBUTOR:
______________________
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 2 of 15
www.parry.co.uk
SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ INSTRUCTIONS FULLY BEFORE USE
Please be aware that surfaces on this machine may get very hot during, and after
use.
ALL APPLIANCES OTHER THAN THOSE FITTED WITH A SEALED
MOULDED PLUG MUST BE FITTED BY A QUALIFIED ELECTRICIAN, IN
ACCORDANCE WITH CURRENT REGULATIONS.
The unit should be installed in compliance with the INSTALLATION
INSTRUCTIONS and the NATIONAL REGULATIONS in force at the time.
Particular attention should be paid to the Health and Safety at Work Act.
To prevent shocks, all appliances whether gas or electric, must be earthed.
To avoid scratching the highly polished exterior surface of this equipment whilst
in transit, the protective film on the exterior surfaces has NOT been removed.
It is IMPORTANT that this protective film is peeled off before the equipment is
used.
ENSURE THE APPLIANCE IS ISOLATED FROM THE POWER SUPPLY
BEFORE INSTALLING, CLEANING OR MAINTAINING THE APPLIANCE
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 3 of 15
www.parry.co.uk
INSTALLATION INSTRUCTIONS
This unit is supplied with a moulded plug
(Optional Extras)
A = Splash Back
B = Soap Dispenser Holder
C = Paper Towel Holder
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 4 of 15
www.parry.co.uk
Optional Extra Fitting Instructions
Remove screws from
handle (A).
Remove both screws
from each side (B).
Place the splashback
(C) on to unit and
replace screws from
(B)
Fitting Soap / Towel holders
Loosen screws (D) in
splashback.
Locate Soap holder /
Towel holder on to the
screws and tighten.
OPERATION INSTRUCTIONS
Position mobile wash basin in desired location.
Remove water tank cover by turning the knob to gain access to water tank. Fill
with water to maximum water level tab, as shown in image below
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 5 of 15
www.parry.co.uk
Ensure waste bucket is in position and the waste pipe is placed inside the
bucket.
Plug into suitable 13amp protected supply.
Ensure switch is in the on position and the red neon illuminated. (Shown in image
below)
Allow 20mins for the water to reach temperature before use.
To fill basin with water use the foot pump at the front of the machine.
Unit is protected from overheating by a control stat. If the tank has an insufficient
amount of water in it, a pressure switch will cut electricity supply to the element
preventing boiling dry, and damage to the element.
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 6 of 15
www.parry.co.uk
Before moving unit to new location make sure water tank is emptied by tap
located on the bottom of the tank as shown in the photo.
Do not attempt to move unit when full of water.
Please note that the waste bucket should be emptied regularly.
IMPORTANT NOTE
After service all water must be drain from the tank.
Disconnect form mains power supply.
Place the bucket below the drain tap. Turn tap and empty the tank.
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 7 of 15
www.parry.co.uk
MAINTENANCE INSTRUCTIONS
Servicing
This appliance should be routinely serviced to prolong its lifetime. Parry
recommends that the appliance is serviced every 12 months by a Parry
authorised engineer. Failure to service your product within the initial 12
month warranty period will cause the 24 month warranty to become void.
MAINTENANCE AND SERVICE MUST ONLY BE UNDERTAKEN BY A
QUALIFIED ELECTRICIAN.
Care and Cleaning
IMPORTANT NOTE
Turn off the mains switch before commencing any of the below.
Proprietary cleaners must be used with care –they are highly corrosive and may
cause damage to surfaces and components.
To clean unit wipe down with warm soapy water.
DO NOT USE SCOURING PADS.
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 8 of 15
www.parry.co.uk
WIRING DIAGRAM
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 9 of 15
www.parry.co.uk
EXPLODED VIEW
(MWBT SHOWN BELOW)
PARTS LIST
ID
DESCRIPTION
PART CODE
1
M16 Gland & Nut
GLAND0M16
LOCKNTM16
2
Plastic Bush
BUPL50006
3
*Gear Tray
*NO CODE
4
Terminal Block
TB3POLETB
5
Pressure Switch
10706/A
6
Thermostat
MWB44CSTAT
7
Barbed Tail
MWBBSPTAIL
8
Sealing Washer (x2)
MWBSEALWASH
9
Brass Lock Nut
MWBLOCKNUT
INSTRUCTION REF: IN262
ISSUE No. 1
DATE 08.03.17
Page 10 of 15
www.parry.co.uk
10
Switch
SWRE06165
11
Switch Cover
LE25COVER
12
Ball Valve
VALVEB12N
13
Nut for Bowl Insert
NUT4BOWLSSS
14
Washer for Bowl Insert
WASS14022
15
Bowl Insert
BOWLINSSL
16
*Air Tray Assembly
*NO CODE
17
Element
ELBW03000
18
*Tank Assembly
*NO CODE
19
Bowl
MWBBOWL
20
Swivel Tap
MWBSWTAPS
21
*Lid
*NO CODE
22
Tap Adaptor & O Ring
MWBTAPFITT
MWBORING
23
Pull Handle
P6BOHANDL
24
Waste Fitting
MWBWASTE
25
*Top
*NO CODE
26
Waste Tube (630mm Length)
MWB24TUBE
27
½” Tube (1060mm Length)
MWB1/2TUBE
28
½” Tube (770mm Length)
MWB1/2TUBE
29
Wheel Bracket (RH)
MWBWHBRKT
30
Castor Wheel
MWBWHEEL
31
Wheel Bracket (LH)
MWBWHBRKT
32
*Body
*NO CODE
33
*Base
*NO CODE
34
Trim (440mm Length)
CARTBLACKTRIM
35
Foot Pump
MWBFOOTPUMP
36
Waste Bucket
MWBUCKET
37
Mains Lead
MLEAD25
38
Vacuum Tube
MWBVACTUBE
Loom
W1 (x2)
W2 (x2)
W17 (x2)
Autres manuels pour MWBT
1
Table des matières
