Paradyne BitStorm 6051 Manuel utilisateur

6051-A2-GZ40-00 April 2002 1

BitStorm™6051 POTS Splitter

Installation Instructions

Document Number 6051-A2-GZ40-00

April 2002

About the BitStorm 6051 POTS Splitter

The BitStorm™ system enables simultaneous high-speed digital data access and

analog voice service over the same twisted-pair telephone line. The BitStorm 6051

POTS (plain old telephone service) splitter card separates the DSL (Digital

Subscriber Line) and POTS frequencies. It provides service to up to 24 DSL ports.

POTS Splitter Chassis

The BitStorm POTS splitter card is mounted in a POTS splitter chassis. Two

chassis models are available:



Chassis Model 5011 – 1-slot chassis which can be placed on a tabletop or

installed in a rack.



Chassis Model 5016 – 6-slot chassis which must be installed in a commercial

EIA-standard 19″or 23″rack or cabinet.

DSL Interface

Loop Interface

PSTN Interface

02-17152

POTS

Splitter Card

2April 2002 6051-A2-GZ40-00

Product-Related Documents

Refer to the following documents for information about the BitStorm 4800 IP

access concentrator.

Contact your sales or service representative to order additional product

documentation.

Paradyne documents are also available on the World Wide Web at

www.paradyne.com. Select

Library

→

Technical Manuals

→

BitStorm DSL

Products.

Installation Overview

Installation of the POTS splitter card requires the following steps:

❑Determining the cables you need

❑Preparing the installation location and checking the package contents

❑Installing the POTS splitter chassis

❑Inserting the POTS splitter card(s) into the chassis

❑Connecting the cabling from the POTS splitter card connectors to the

BitStorm 4800, local loop, and in-building wiring

❑Securing the cables

Be sure to register your warranty at www.paradyne.com/warranty.

Document Number Document Title

4800-A2-GB20

BitStorm 4800 User’s Guide

4800-A2-GN10

BitStorm 4800 Management Module Installation

Instructions

4821-A2-GN20

BitStorm 4800 Installation Guide

6051-A2-GZ40-00 April 2002 3

Cables You Need

The POTS splitter card has three interfaces and each of the three POTS Splitter

card connectors requires a 50-conductor cable with a 50-pin Telco connector. Use

a minimum of 24 AWG.

Each DSL port at the BitStorm 4800 uses one pair of copper wires out of the

25 pairs on each 50-position connector. To use all 48 ports, two POTS splitter

cards and six cables are required.

Preparation

The installation location should be well ventilated, clean, and free of environmental

extremes. Allow clearance at the front of the POTS splitter chassis to provide

access to the cables.

Read the

Important Safety Instructions

on page 17.

Tools Required



A small #1 or #2 Phillips screwdriver to tighten the POTS splitter card

fasteners.



A large #3 or #4 Phillips screwdriver to install the chassis into a rack.



A flat-blade screwdriver to install the chassis grounding wire.

POTS Splitter Card Package Checklist

Verify that your POTS splitter card package contains the following:

❑BitStorm 6051 POTS splitter card

❑Plastic bag with three of each item:

—Plastic tie-wrap anchors

—#4-40 x 1/4″screws

—#4-40 x 1/4″jack screws

—8″cable tie wraps

4April 2002 6051-A2-GZ40-00

1-Slot 5011 POTS Splitter Chassis Package Checklist

Verify that your 1-slot POTS splitter chassis package contains the following:

❑1-slot POTS splitter chassis

❑Two brackets for 19″racks and two brackets for 23″racks

❑Small plastic bag with:

—Six #10-32 x 1/4″Phillips flat-head mounting screws

—Four #10-32 x 1/2″Phillips-head mounting screws

—Four #12-24 x 1/2″Phillips-head mounting screws

—Four #12-24 self-retaining nuts

—Four black rubber feet

NOTE:

If your 1-slot 5011 POTS splitter chassis is being placed on a tabletop, install

the rubber feet as shown above. Discard the rubber feet for a rack-mounted

chassis.

02-17153

POTS Splitter

1-Slot Chassis

Placement of

Rubber

Feet

6051-A2-GZ40-00 April 2002 5

6-Slot 5016 POTS Splitter Chassis Package Checklist

Verify that your 6-slot POTS splitter chassis package contains the following:

❑6-slot POTS splitter chassis with five filler panels. Each filler panel is attached

to the chassis with two 1/4-turn fasteners. Keep filler panels installed in all

unused slots.

❑Two brackets for 483 mm (19″)racks and two brackets for 584 mm (23″)racks

❑Small plastic bag with:

—Six #10-32 x 1/4″Phillips flat-head mounting screws

—Four #10-32 x 1/2″Phillips-head mounting screws

—Four #12-24 x 1/2″Phillips-head mounting screws

—Four #12-24 self-retaining nuts

—Four black rubber feet (discard)

02-17154

POTS Splitter

6-Slot Chassis

Filler

Panels

6April 2002 6051-A2-GZ40-00

POTS Splitter Chassis Installation

Both the POTS splitter chassis and the BitStorm 4800 are shipped with mounting

brackets that allow them to be mounted in a 483 mm (19″)or 584 mm (23″)

cabinet or rack.

In preparation for bracket and chassis installation, determine:



Whether the BitStorm 4800 will be rack-mounted.



Width of the rack: 483 mm (19″)or 584 mm (23″).



Chassis position in the rack: center-mounted or front-mounted.

Center-mounting is recommended for convenient access to cables.



Whether the rack has mounting rails with threaded or non-threaded screw

holes.

NOTE:

Install chassis in the rack from the bottom up to maintain stability.

02-17158

DSLPORTS1-24

DSL PORTS 25-48

UPLINK

GigE DOWNLINK

GigE

STACKPOSITION

Front

Rear

POTS Splitter

Card in 1-Slot

Chassis

BitStorm 4800

6051-A2-GZ40-00 April 2002 7

Installing the Brackets

The brackets can be installed in the chassis in a center-mounted or front-mounted

configuration. Mounting holes are provided in the chassis for either configuration.

Install the appropriate 483 mm (19″) or 584 mm (23″)brackets on the 1-slot or

6-slot chassis.

Select one of the next two procedures for chassis installation in a rack.

19-Inch Rack

23-Inch Rack

99-15486-02

1-Slot Chassis

19-Inch Rack

23-Inch Rack

99-15434-02

Front Mount

Center Mount

6-Slot Chassis

8April 2002 6051-A2-GZ40-00

Installation into a Rack without Threaded Screw Holes

Procedure

After installing the appropriate brackets on the chassis:

1. Determine where the chassis will be placed in the rack. Mark the front rail

where the four holes in the mounting brackets will be.

2. Slide a self-retaining nut onto each marked rail hole and align the hole of the

nut with the hole in the rail.

3. Line up the chassis mounting brackets with the self-retaining nuts.

4. Loosely install the bottom screws first and then the top screws.

5. Tighten all screws firmly using a Phillips screwdriver.

Repeat the process for each POTS splitter chassis. POTS splitter chassis can be

mounted directly on top of each other.

Front Rail

00-15436-02

Screw

Self-Retaining

Nut

6051-A2-GZ40-00 April 2002 9

Installation into a Rack with Threaded Screw Holes

Procedure

After installing the appropriate brackets on the chassis:

1. Determine where the chassis will be placed in the rack.

2. Line up the chassis mounting brackets with the front rail holes.

3. Loosely install the bottom screws first and then the top screws.

4. Tighten all screws firmly with a Phillips screwdriver.

Repeat the process for each POTS splitter chassis. POTS splitter chassis can be

mounted directly on top of each other.

Front Rail

99-15435-01

Screw

10 April 2002 6051-A2-GZ40-00

Installing the Ground Wire

To comply with Network Equipment Building System (NEBS) requirements, the

ground wire must be installed.

Procedure

1. Obtain copper wire of appropriate wire gauge:

2. Strip back the insulation approximately 6 mm (1/4″) on the copper wire.

3. Locate the grounding lug on the chassis:

4. Loosen the screw on the

grounding lug.

5. Insert the stripped end of the

wire into the open end of the

grounding lug and tighten the

lug’s screw. Make sure that

the screw is making contact

with the stripped portion of

the wire.

If you have a . . . Then the ground wire gauge must be . . .

1-slot 5011 chassis 10–14 AWG.

6-slot 5016 chassis 6–14 AWG.

If you have a . . . Then the grounding lug is . . .

1-slot chassis On the rear of the chassis on the left.

6-slot chassis On the front of the chassis on the top right.

POTS Splitter

1-Slot Chassis

02-17155

POTS Splitter

6-Slot Chassis

98-15879-01

Autres manuels pour BitStorm 6051

Table des matières

Autres manuels Paradyne Câbles et connecteurs

Paradyne

Paradyne 5030 Manuel utilisateur

Paradyne

Paradyne Hotwire 5038-A1-00 Manuel utilisateur

Paradyne

Paradyne BitStorm 6051 Manuel utilisateur

Paradyne

Paradyne 5034 Manuel utilisateur

Paradyne

Paradyne Hotwire 5020 Manuel utilisateur

Paradyne

Paradyne 9261 Manuel utilisateur

Paradyne

Paradyne Hotwire 6050 Manuel utilisateur

Paradyne

Paradyne Hotwire 7034 Manuel utilisateur

Paradyne

Paradyne 3511 DSU Manuel utilisateur

Paradyne

Paradyne Hotwire 6020 Manuel utilisateur

Paradyne

Paradyne 5011 Manuel utilisateur

Paradyne

Paradyne HotWire 5034 Manuel utilisateur

Paradyne

Paradyne 5030 Manuel utilisateur

Manuels Câbles et connecteurs populaires d'autres marques

Philips

Philips SWA6310 Manuel utilisateur

StarTech.com

StarTech.com CRJ4550PK Manuel utilisateur

Nohau

Nohau EMUL-IP2K-PC Manuel utilisateur

Foxun

Foxun SX-SP144E-HD4K2K Manuel utilisateur

Philips

Philips SWA3305W Manuel utilisateur

opticis

opticis Stretch DVIM1-1P0x Manuel utilisateur

Volkswagen

Volkswagen VAS 6558A Manuel utilisateur

NEXIBO

NEXIBO N-13 Manuel utilisateur

CYP

CYP PU-1H3HBTL Manuel utilisateur

Allen-Bradley

Allen-Bradley 1784-u2dhp Manuel utilisateur

Global Caché

Global Caché Flex Link Blaster Manuel utilisateur

Hauppauge

Hauppauge USB-Live2 Manuel utilisateur

Fenix

Fenix MPSV 15 Manuel utilisateur

BEGA

BEGA 71 085 Manuel utilisateur

Tesla

Tesla HPWC Manuel utilisateur

GAMERON

GAMERON LUXURY TV CABLE Manuel utilisateur

molex

molex Milli-Grid Dual row 87568 Series Manuel utilisateur

Burndy

Burndy Continental Industries thermOweld CRE-7 Manuel utilisateur