Paradigm Connect70 Manuel utilisateur
Installation Guide
Connect70
GX
G
G
Paradigm
- 2 -
GX
G
G
Paradigm
The information in this document has been carefully compiled and checked for technical
accuracy. Paradigm Communication Systems Ltd. accept no liability for inaccuracies or errors. In
line with the company policy of technical advancement, the information within this document may
be changed. The user should ensure that the correct issue of the document is used.
Paradigm assumes no responsibility for the use of this document if any unauthorised changes to
the content or format are made.
This document is provided without implied or expressed warranty of any kind, including but not
limited to the implied warranties of merchantability and tness for purpose.
Other manufacturers’ registered trademarks and trade names which appear in this document are
hereby acknowledged.
Comments or correspondence regarding this document should be addressed to:
Paradigm Communication Systems Limited
Paradigm House
14 Wilsom Road
Alton, Hampshire
GU34 2PP
England
Tel: +44 (0) 1420 88199
Fax: +44 (0) 1420 88842
Email: [email protected]
© Paradigm Communication Systems Limited 2015. All rights reserved.
No part of this document may be reproduced in any form without the prior written consent of
Paradigm Communication Systems Limited. Use of the information contained herein is strictly
reserved for Paradigm Communication Systems Limited. Other use in any form and/or by any
means whatsoever is strictly prohibited.
DN: ED-IMA-02396
Rev: 04
Release Date: 23/07/2015
Legal
Safe Use
WARNING
Radiation Hazard. Transmitter power levels are sufcient to cause blindness or other serious
injury to body tissue. Do not power on the PIM and Transceiver until it is safe to do so.
WARNING
Risk of Electric Shock. High voltages exist within the units and the cables providing power to
the units. Always remove power from these devices when performing maintenance. Do not
modify power cables or physical unit in any way.
The equipment described in this manual is intended to be installed, used and operated only
for the purpose for which it was designed, in accordance with the safety procedures and any
other instructions given in this manual. Nothing stated in this manual reduces the professional
responsibilities of users for the exercise of sound judgement and best practice.
WARNING
This equipment is intended for installation in a restricted access location. The equipment
should not be touched during operation.
- 3 -
Installation Guide
Connect70
Contents Safe Use ............................................................................................................2
Legal ..................................................................................................................2
Contents............................................................................................................3
Site Survey for Antenna Installation ...............................................................4
Installation Process..........................................................................................4
Antenna Packaging Content............................................................................5
Recommended Tools for Installation..............................................................5
Skew adjustment............................................................................................6
Attach the Az/El mount...................................................................................7
Attach Antenna dish to Az/El mount ...............................................................8
Attach Boom to Az/El mount ..........................................................................9
Mounting the Transceiver.............................................................................10
RF Circuit Setup .............................................................................................11
Antenna Adjustment ......................................................................................12
Skew Adjustment..........................................................................................12
Elevation Adjustment....................................................................................12
Azimuth Adjustment .....................................................................................13
Antenna Grounding........................................................................................14
Skew Calculation Chart..................................................................................15
Elevation Calculation Chart...........................................................................16
Azimuth Calculation Chart.............................................................................17
Transceiver Control LEDs..............................................................................18
Transceiver Port Identication......................................................................18
Pointing with Skew.........................................................................................19
Periodic Maintenance.....................................................................................19
- 4 -
GX
G
G
Paradigm
All equipment necessary for the assembly of this Antenna Terminal is included. To complete the
pointing process, a portable computer may be necessary.
Installation
Process
Investigate the intended installation site for the satellite antenna, and using the azimuth and
elevation angles provided by the PIM (see PIM Operators Manual), conrm there are no line-
of-sight obstructions. Remove any obstructions if possible, or select a new location with a clear
line-of-sight to the satellite.
Site Survey
for Antenna
Installation
1. Install the Antenna mount
• Wall Mount
• Non-Penetrating
Roof Mount
• Kingpost
• Tripod
2. Assemble and Install the
Antenna
4. Point the antenna
• Coarse Pointing
• Fine Pointing
5. Commission the
installation
3. Assemble RF Circuit
• Transceiver
• PIM
Refer to the ParadigmGX Antenna Mount Installation Manual
- 5 -
Installation Guide
Connect70
Package Contents:
1. 69cm 1-piece pressed-steel antenna
2. Az/El mount
3. Antenna Rear Bracket
4. Skew Plate
5. Boom Arms
6. 5W Ka-Band transceiver with integrated feed
7. Transceiver Mounting Bracket
8. IFL Cable (M&C, Tx, Rx), optional Paradigm-GPS
9. PIM (Outdoor, Indoor, or Rack Mount)
10. Assembly nuts, bolts and washers
11. Tool Kit, Tie-wraps, Compass, Amalgamating tape
1
2
3
4
Antenna
Packaging
Content
5
6
7
Compass & Inclinometer
Spirit level
Torque wrench
Spectrum Analyser
Portable Computer to complete the pointing process
Recommended
Tools for
Installation
- 6 -
GX
G
G
Paradigm
Skew
adjustment
Referring to the skew angle calculator on page 15 and the skew adjustment process on
page 12, set the skew angle for the satellite antenna. Rotate the antenna rear bracket to the
calculated skew angle, and tighten the M8 nylon insert hex nuts using the 1/2” ring spanner. Set
the Az/El mount elevation to the approximate elevation of the satellite.
- 7 -
Installation Guide
Connect70
Attach the Az/El
mount
Attach the Az/El mount to the antenna mount post. Do not secure the clamp at this time, but
allow the antenna free movement through azimuth.
Referring to the skew angle calculator on page 15 and the elevation adjustment process on
page 12, set the coarse elevation for the satellite antenna.
Referring to the azimuth adjustment process on page 13, set the coarse azimuth.
- 8 -
GX
G
G
Paradigm
Attach Antenna
dish to Az/El
mount
Attach the antenna reector to the Az/El mount by locating the 4 M8x20mm bolts and M8 nylon
insert hex nuts and secure using the 13mm ring spanner.
- 9 -
Installation Guide
Connect70
Attach Boom to
Az/El mount
Slide the boom through the antenna reector into the bracket base. Secure the boom using 5/16”
x 3/4” hex bolts, an 8.4mm at washer and an 8.4mm spring washer. Secure rmly into place by
tightening each bolt using the 13mm ring spanner.
- 10 -
GX
G
G
Paradigm
Mounting the
Transceiver
Attach the transceiver to the transceiver mounting bracket using the using 4 x M6x18mm hex-
socket bolts. Tighten using the 5mm hex key.
Attach the transceiver mounting bracket to the boom using 5/16” x 3/4” hex bolts, an 8.4mm at
washer and an 8.4mm spring washer. Secure rmly into place by tightening each bolt using the
13mm ring spanner.
Table des matières
Autres manuels Paradigm Antenne
Manuels Antenne populaires d'autres marques
Alfa Network
Alfa Network APA-L01 Manuel utilisateur
Naval
Naval PR-422CA Manuel utilisateur
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur
TERK Technologies
TERK Technologies TV44 Manuel utilisateur
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur
HP
HP J8999A Manuel utilisateur
CommScope
CommScope CMAX-OMFX-43M-I53 Manuel utilisateur
Ramsey Electronics
Ramsey Electronics DAP25 Manuel utilisateur
COBHAM
COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien
Trango Systems
Trango Systems AD900-9 Manuel utilisateur
Steren
Steren ANT-100 Manuel utilisateur
Proxim
Proxim 5054-PA-23 Manuel utilisateur