Panduit T568A Manuel utilisateur

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 1 of 4

Specifications

• Cable jacket diameter 0.285 in. max.

• Maximum conductor insulation diameter 0.041 in.

• Panduit recommends T568B wiring scheme for use

with cable constructed with the brown pair opposing

the orange pair.

Conductor holes and Contact slots

1Thread boot and collar onto the cable first.

Remove 2.0" of the outer jacket from the cable end using

wire stripping tool (CJAST).

Remove matrix foil to expose twisted pairs.

Fan twisted pairs into respective quadrants. The brown

pair should be opposite the orange pair.

When a cable spline (X-shaped filler) is present, cut spline

flush to fanned pairs using wire snipping tool (CWST).

Thread on boot

and collar first!

(Cable ends 1 & 2)

90°

CWST

Strain Relief Boot

Strain Relief Collar

Divider

Load Bar

Plug Housing

Load Bar

Divider

Conductor slots and “V” channel

2Note orientation of the divider depending on cable end 1

or cable end 2. The “V” channel should be aligned with the

green pair.

Insert divider posts into the cable. If the cable has an

internal spline, insert divider posts into the brown and

orange quadrants of the spline.

BLU

GRN

“V” channel

BRN

ORG

GRN

BLU

BRN

ORG

(Cable end 2)

(Cable end 1)

“V” channel

3Arrange conductors to T568B wiring scheme while

minimizing untwist and smooth conductors.

Seat conductors into proper divider slots while holding

divider near the end of the cable jacket.

“V” channel

(Cable end 1) (Cable end 2)

T568B Wiring Scheme

T568B BRN

WHT

BRN/

GRN WHT

BLU/

BLU WHT

GRN/

ORG WHT

ORG/

Pin #

“V” channel

Conductor holes

Contact slots Divider post

Pins

* Denotes packaging quantity.

Category 6A UTP Modular Plug

for Panduit Patch Cable

T568B & T568A

Part Number: SP6X88P-*

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 2 of 4

(Cable end 1)

Guide conductors into load bar holes while holding

conductors in the divider.

Slide load bar towards divider until flush.

Ensure the divider/load bar is centered and perpendicular

to the cable axis.

Trim conductors flush with load bar face.

Verify

Load Bar

orientation

5Orient load bar with contact slots facing downward.

(Cable end 1)

(Cable end 2)

Pins

4While holding conductors in respective divider slots,

straighten and align untwisted conductors using a circular

motion.

Do not release grip of conductors until load bar is applied

in order to maintain conductor alignment.

Trim conductors on an angle approximately 1.00" from

divider leading edge.

1.00"

T568B BRN

WHT

BRN/

GRN WHT

BLU/

BLU WHT

GRN/

ORG WHT

ORG/

Pin #

(Cable end 1)

10 MPT5-8AS

Grip and squeeze across collar arms as sub-assembly

is inserted into plug housing.

Push sub-assembly into housing until collar locking tabs

clear the plug housing pocket. Although not required, TX6

PLUS Plug Assembly Tool (CSPT) is available to facilitate

this step.

Slide boot forward and fully seat onto strain relief collar.

Use tool MPT5-8AS to complete termination.

Assembly is complete. Visually check plug.

While holding load bar and divider stationary, slide collar

and boot forward until there is no gap between collar and

divider. Do not exert pressure onto divider as collar can

push load bar off conductors.

Confirm orientation of collar.

Align pin #1 of cable sub-assembly with pin #1 of plug

housing.

(Cable end 1)

(Cable end 2)

Pins

Collar locking

tabs

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 3 of 4

T568A Wiring Scheme

T568A BRN

WHT

BRN/

ORG WHT

BLU/

BLU WHT

ORG/

GRN WHT

GRN/

Pin #

1Thread boot and collar onto the cable first.

Remove 2.0" of the outer jacket from the cable end using

wire stripping tool (CJAST).

Remove matrix foil to expose twisted pairs.

Fan twisted pairs into respective quadrants. The brown

pair should be opposite the green pair.

When a cable spline (X-shaped filler) is present, cut spline

flush to fanned pairs using wire snipping tool (CWST).

Thread on Boot

and Collar first!

(Cable ends 1 & 2)

90°

CWST

2Note orientation of the divider depending on cable end 1

or cable end 2. The “V” channel should be aligned with the

orange pair.

Insert divider posts into the cable. If the cable has an

internal spline, insert divider posts into the brown and

green quadrants of the spline.

BLU

ORG

“V” channel

BRN

GRN

ORG

BLU

BRN

GRN

(Cable end 2)

(Cable end 1)

“V” channel

3Arrange conductors to T568A wiring scheme while

minimizing untwist and smooth conductors.

Seat conductors into proper divider slots while holding

divider near the end of the cable jacket.

“V” channel

(Cable end 1) (Cable end 2)

Conductor holes and Contact slots

Load Bar Divider

Conductor slots and “V” channel

“V” channel Divider post

Conductor holes

Contact slots

Pins

Specifications

• Cable jacket diameter 0.285 in. max.

• Maximum conductor insulation diameter 0.041 in.

• Panduit recommends T568A wiring scheme for use

with cable constructed with the brown pair opposing

the green pair.

Strain Relief Boot

Strain Relief Collar

Divider

Load Bar

Plug Housing

INSTALLATION INSTRUCTIONS

E-mail:

[email protected]m

Phone:

866-405-6654

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp www.panduit.com

Page 4 of 4

4While holding conductors in respective divider slots,

straighten and align untwisted conductors using a circular

motion.

Do not release grip of conductors until load bar is applied

in order to maintain conductor alignment.

Trim conductors on an angle approximately 1.00" from

divider leading edge.

1.00"

T568A BRN

WHT

BRN/

ORG WHT

BLU/

BLU WHT

ORG/

GRN WHT

GRN/

Pin #

(Cable end 1)

5Orient load bar with contact slots facing downward.

(Cable end 1)

(Cable end 2)

Pins

Verify

Load Bar

orientation

Pins

(Cable end 1)

Guide conductors into load bar holes while holding

conductors in the divider.

Slide load bar towards divider until flush.

Ensure the divider/load bar is centered and perpendicular

to the cable axis.

Trim conductors flush with load bar face.

10 MPT5-8AS

Grip and squeeze across collar arms as sub-assembly

is inserted into plug housing.

Push sub-assembly into housing until collar locking tabs

clear the plug housing pocket. Although not required, TX6

PLUS Plug Assembly Tool (CSPT) is available to facilitate

this step.

Slide boot forward and fully seat onto strain relief collar.

Use tool MPT5-8AS to complete termination.

Assembly is complete. Visually check plug.

While holding load bar and divider stationary, slide collar

and boot forward until there is no gap between collar and

divider. Do not exert pressure onto divider as collar can

push load bar off conductors.

Confirm orientation of collar.

Align pin #1 of cable sub-assembly with pin #1 of plug

housing.

8(Cable end 2)

Pins

(Cable end 1)

Collar locking

tabs

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panduit Câbles et connecteurs

Panduit

Panduit CM308F Guide de configuration

Panduit

Panduit FS148 Manuel utilisateur

Panduit

Panduit CJS588T Manuel utilisateur

Panduit

Panduit PN366E Manuel utilisateur

Panduit

Panduit Opti-Core Manuel utilisateur

Panduit

Panduit FJJGM2.0C Manuel utilisateur

Panduit

Panduit VeriSafe VSC Series Manuel utilisateur

Panduit

Panduit T568B Manuel utilisateur

Panduit

Panduit TX5e Manuel utilisateur

Panduit

Panduit CT-1000 Fiche technique

Panduit

Panduit PND110 Manuel utilisateur

Panduit

Panduit FK2BJ Manuel utilisateur

Panduit

Panduit PAN-SHRINK HSTTT Series Manuel utilisateur

Panduit

Panduit NetKey 6 Series Manuel utilisateur

Panduit

Panduit FSCMM Series Manuel utilisateur

Panduit

Panduit VeriSafe VS-CKP14-6 Manuel utilisateur

Panduit

Panduit KMTRTH Manuel utilisateur

Panduit

Panduit DP6 PLUS Manuel utilisateur

Panduit

Panduit CHD15HDSC Y Series Manuel utilisateur

Panduit

Panduit DPA245E88TV25 Manuel utilisateur

Panduit

Panduit FLCSHMIG Manuel utilisateur

Panduit

Panduit CRB6BL Manuel utilisateur

Panduit

Panduit PCPA13R20 Series Manuel utilisateur

Panduit

Panduit IAEBH5E Manuel utilisateur

Manuels Câbles et connecteurs populaires d'autres marques

Philips

Philips SWA6310 Manuel utilisateur

StarTech.com

StarTech.com CRJ4550PK Manuel utilisateur

Nohau

Nohau EMUL-IP2K-PC Manuel utilisateur

Foxun

Foxun SX-SP144E-HD4K2K Manuel utilisateur

Philips

Philips SWA3305W Manuel utilisateur

opticis

opticis Stretch DVIM1-1P0x Manuel utilisateur

Volkswagen

Volkswagen VAS 6558A Manuel utilisateur

NEXIBO

NEXIBO N-13 Manuel utilisateur

CYP

CYP PU-1H3HBTL Manuel utilisateur

Allen-Bradley

Allen-Bradley 1784-u2dhp Manuel utilisateur

Global Caché

Global Caché Flex Link Blaster Manuel utilisateur

Hauppauge

Hauppauge USB-Live2 Manuel utilisateur

Fenix

Fenix MPSV 15 Manuel utilisateur

BEGA

BEGA 71 085 Manuel utilisateur

Tesla

Tesla HPWC Manuel utilisateur

GAMERON

GAMERON LUXURY TV CABLE Manuel utilisateur

molex

molex Milli-Grid Dual row 87568 Series Manuel utilisateur

Burndy

Burndy Continental Industries thermOweld CRE-7 Manuel utilisateur