Panasonic Omnivision PV-9661 Manuel utilisateur

file:///E:/PV-9661_PV-9662/SVC/s0000000000.html

Service Manual

TOP NEXT

ORDER NO. MKE9901002C1

Video Cassette Recorder

● PV-9661/PV-9662

violation of law.

file:///E:/PV-9661_PV-9662/SVC/s0000000000.html (1 z 2) [2006-01-28 11:08:20]

file:///E:/PV-9661_PV-9662/SVC/s0000000000.html

TOP NEXT

file:///E:/PV-9661_PV-9662/SVC/s0000000000.html (2 z 2) [2006-01-28 11:08:20]

file:///E:/PV-9661_PV-9662/SVC/s0100000000x.html

1 SAFETY PRECAUTIONS

TOP PREVIOUS NEXT

GENERAL GUIDELINES

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment which are important for safety. These

parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and

ReplacementParts List. It is essential that these critical parts should be replaced with

manufacturer´s specified parts to prevent shock, fire or other hazards. Do not modify the

original design without permission of manufacturer.

2. An Isolation Transformer should always be used during the servicing of VCR whose chassis is

not isolated from the AC power line. Use a transformer of adequate power rating as this

protects the technician from accidents resulting in personalinjury from electrical shocks. It will

also protect VCR from being damaged by accidental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts

which have been overheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices such as insulation barriers, insulation

papers shields are properly installed.

5. After servicing, make the following leakage current checks to prevent the customer from being

exposed to shock hazards.

LEAKAGE CURRENT COLD CHECK

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each

exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts,

etc. When the exposed metallic part has a return path to thechassis, the reading should be

between 1M ohm and 5.2M ohm. When the exposed metal does not have a return path to the

chassis, the reading must be infinity.

Figure 1

file:///E:/PV-9661_PV-9662/SVC/s0100000000x.html (1 z 2) [2006-01-28 11:08:30]

file:///E:/PV-9661_PV-9662/SVC/s0100000000x.html

LEAKAGE CURRENT HOT CHECK

(See figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this

check.

2. Connect a 1.5K ohm, 10 watts resistor, in parallel with a 0.15 microfarad capacitor, between

each exposed metallic part on the set and a good earth ground, as shown in figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across

the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester

(Simpson Model 229 or equivalent) may be used to make the hot checks. Leakage current must

not exceed 1/2 milliamp. In case a measurement is outsideof the limits specified, there is a

possibility of a shock hazard, and the equipment should be repaired and rechecked before it is

returned to the customer.

TOP PREVIOUS NEXT

file:///E:/PV-9661_PV-9662/SVC/s0100000000x.html (2 z 2) [2006-01-28 11:08:30]

file:///E:/PV-9661_PV-9662/SVC/s0200000000x.html

2 PREVENTION OF ELECTROSTATIC

DISCHARGE (ESD) TO

ELECTROSTATICALLY SENSITIVE (ES)

DEVICES

TOP PREVIOUS NEXT

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such

components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits, some field-effect transistorsand semiconductor "chip" components.

The following techniques should be used to help reduce the incidence of component damage caused

by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped

assembly, drain off any ESD on your body by touching a known earth ground. Alternatively,

obtain and wear a commercially available discharging ESD wrist strap,which should remove

electrostatic charge for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a

conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure

of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as

"antistatic (ESD protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to

damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before

you are ready to install it. (Most replacement ES devices are packaged with leads electrically

shorted together by conductive foam, aluminum foil or comparableconductive material).

7. Immediately before removing the protective material from the leads of a replacement ES

device, touch the protective material to the chassis or circuit assembly into which the device

will be installed.

CAUTION:Be sure no power is applied to the chassis or circuit, and observe all other safety

precautions.

file:///E:/PV-9661_PV-9662/SVC/s0200000000x.html (1 z 2) [2006-01-28 11:08:32]

file:///E:/PV-9661_PV-9662/SVC/s0200000000x.html

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise

harmless motion such as the brushing together of your clothes fabric or the lifting of your foot

from a carpeted floor can generate static electricity (ESD)sufficient to damage an ES device).

"NOTE to CATV system installer:

This reminder is provided to call the CATV system installer´s attention to Article 820-22 of the NEC

that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall

be connected to the grounding systemof the building, as close to the point of cable entry as practical."

TOP PREVIOUS NEXT

file:///E:/PV-9661_PV-9662/SVC/s0200000000x.html (2 z 2) [2006-01-28 11:08:32]

file:///E:/PV-9661_PV-9662/SVC/s0300000000o.html

3 OPERATION GUIDE

TOP PREVIOUS NEXT

file:///E:/PV-9661_PV-9662/SVC/s0300000000o.html [2006-01-28 11:08:40]

file:///E:/PV-9661_PV-9662/SVC/s0400000000x.html
SERVICE NOTES (PLEASE READ)
TOP PREVIOUS NEXT 
1 SERVICE NOTES 
1.1 SIMPLIFIED FAULT FINDING DATA 
1.2 SERVICE POSITION 
1.2.1 Basic Service Position 
1.2.1.1 Service Position (1) 
1.2.1.2 Service Position (2) 
1.2.2 Service Position with Extension Cable Kit 
1.2.2.1 Service Position 
1.2.2.2 Extension Cable Kit (VUZS0002) 
1.2.2.3 How to place the unit in the Service Position (1) 
1.3 HOT CIRCUIT 
1.4 SERVICE MODE 
1.5 INSTALLATION OF FRONT PANEL ASS´Y CAUTION 
1.6 METHOD FOR LOADING/UNLOADING OF MECHANISM 
1.7 HOW TO REMOVE A JAMMED TAPE 
1.7.1 Manual Method 
1.7.1.1 Method -1: 
1.7.1.2 Method -2: 
file:///E:/PV-9661_PV-9662/SVC/s0400000000x.html (1 z 2) [2006-01-28 11:08:49]

file:///E:/PV-9661_PV-9662/SVC/s0400000000x.html

4.1.7.1.3 Method -3:

4.1.7.2 Electrical Method

4.1.8 DEFEATING THE AUTO TRACKING

4.1.9 HOW TO SET TRACKING TO THE NEUTRAL POSITION

4.1.10 CYLINDER ROTATION IN STOP MODE

4.1.11 BLACK SCREWS ON THE CHASSIS

4.1.12 HOW TO RESET ALL VCR MEMORY FUNCTIONS

4.1.13 VARIABLE VOLTAGE ISOLATION TRANSFORMER

4.1.14 SPECIAL NOTE

4.1.15 REPLACEMENT PROCEDURE FOR LEADLESS (CHIP) COMPONENTS

4.1.16 MODEL NO. IDENTIFICATION MARK

4.2 IC, TRANSISTOR AND CHIP PART INFORMATION

4.2.1 HOW TO READ THE IDENTIFICATION MARK OF CHIP COMPONENTS.

4.2.2 HOW TO READ THE VALUES OF THE CYLINDRICAL TYPE CHIP COMPONENTS.

TOP PREVIOUS NEXT

file:///E:/PV-9661_PV-9662/SVC/s0400000000x.html (2 z 2) [2006-01-28 11:08:49]

file:///E:/PV-9661_PV-9662/SVC/s0401000000.html
1 SERVICE NOTES
TOP PREVIOUS NEXT 
1.1 SIMPLIFIED FAULT FINDING DATA 
1.2 SERVICE POSITION 
1.2.1 Basic Service Position 
1.2.1.1 Service Position (1) 
1.2.1.2 Service Position (2) 
1.2.2 Service Position with Extension Cable Kit 
1.2.2.1 Service Position 
1.2.2.2 Extension Cable Kit (VUZS0002) 
1.2.2.3 How to place the unit in the Service Position (1) 
1.3 HOT CIRCUIT 
1.4 SERVICE MODE 
1.5 INSTALLATION OF FRONT PANEL ASS´Y CAUTION 
1.6 METHOD FOR LOADING/UNLOADING OF MECHANISM 
1.7 HOW TO REMOVE A JAMMED TAPE 
1.7.1 Manual Method 
1.7.1.1 Method -1: 
1.7.1.2 Method -2: 
1.7.1.3 Method -3: 
file:///E:/PV-9661_PV-9662/SVC/s0401000000.html (1 z 2) [2006-01-28 11:08:50]

Autres manuels pour Omnivision PV-9661

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Système de magnétoscope

Panasonic

Panasonic AJ-D230H Manuel utilisateur

Panasonic

Panasonic NV-SJ230A Manuel utilisateur

Panasonic

Panasonic NV-HD642EE Manuel utilisateur

Panasonic

Panasonic PV-V462 Manuel utilisateur

Panasonic

Panasonic NV-SD10 Series Manuel utilisateur

Panasonic

Panasonic Omnivision PV-V4621 Manuel utilisateur

Panasonic

Panasonic NV-SV120EG Manuel utilisateur

Panasonic

Panasonic NV-D48 Series Manuel utilisateur

Panasonic

Panasonic Omnivision PV-V4523S Manuel utilisateur

Panasonic

Panasonic AJ-HD3700AP Manuel utilisateur

Panasonic

Panasonic DVCPRO AJ-D640P Manuel utilisateur

Panasonic

Panasonic AJHD3700B-PE Manuel utilisateur

Panasonic

Panasonic PV-V4623S Manuel utilisateur

Panasonic

Panasonic NV-SD437EE Manuel utilisateur

Panasonic

Panasonic NV-G25 Series Manuel utilisateur

Panasonic

Panasonic NV-HD100EA Manuel utilisateur

Panasonic

Panasonic NV-J35 Series Manuel utilisateur

Panasonic

Panasonic AJ-SD255 - Professional Editing Video Cassete... Manuel utilisateur

Panasonic

Panasonic Omnivision PV-4664 Manuel utilisateur

Panasonic

Panasonic AG7450AP - HI-FI VCR/BRC Manuel utilisateur

Panasonic

Panasonic Omnivision PV-8455S Manuel utilisateur

Panasonic

Panasonic AJHD1800 - VTR DVCPRO HD Manuel utilisateur

Panasonic

Panasonic NV-SD400 Series Manuel utilisateur

Panasonic

Panasonic OmniVision PV-QV200 Manuel utilisateur

Manuels Système de magnétoscope populaires d'autres marques

Toshiba

Toshiba M-662 Manuel utilisateur

Sony

Sony GV-500 Primary Manuel utilisateur

JVC

JVC HR-J282EU Manuel utilisateur

Sony

Sony HDCAM-SR SRW5800 Manuel utilisateur

Magnavox

Magnavox VRU242AT Manuel utilisateur

Sony

Sony HVR-M10C Manuel utilisateur

RCA

RCA VR634HF - Hi-Fi VCR Manuel utilisateur

JVC

JVC HR-5910U Manuel utilisateur

JVC

JVC HR-S8600EU Manuel utilisateur

JVC

JVC HR-FS1U Manuel utilisateur

Sharp

Sharp VC-H9888U Manuel utilisateur

FUNAI

FUNAI LC-950 Manuel utilisateur

Sharp

Sharp VC-S2000GM Manuel utilisateur

Sony

Sony Video8 EV-A60 Manuel utilisateur

Aiwa

Aiwa HV-E212 Manuel utilisateur

JVC

JVC HR-J3006UM Manuel utilisateur

GE VG4271 Manuel utilisateur

RCA

RCA VR678HF Manuel utilisateur