Panasonic SB-WA920PP Manuel utilisateur

ORDERNO. MD0403057C1

ActiveSubwooferSystem

SB-WA920PP

Colour

(S)...SilverType

SPECIFICATIONS

Specification

Activesubwoofer

Type 1way, 1speakersystem (Bass

reflex)

Speakerunit Impedance 4

Woofer 20 cm (7-7/8”)Conetype

Outputsound pressure 84 dB/W (1.0m)

Frequencyrange 34 Hz-220 Hz(-16 dB)

38 Hz-190 Hz(-10 dB)

Dimensions(W xHxD) 285 x418 x475 mm

(11-7/32”x16-15/32”x18-11/16”)

Mass 15 kg (33 lb.)

General

Powerconsumption 390V

Powersupply AC120V, 60Hz

Note:

Specificationsaresubjectto changewithoutnotice.

Mass and dimensionsareapproximate.

SB-HT920P-S consistsof:

SB-PF920P-S x2, SB-PS920P-S x2and SB-PC920P-S x1

System :SC-HT920 (P) MusicCenter:SA-HT920 (P)

SatelliteSpeakers:SB-HT920 (P)

ActiveSubwoofer:SB-WA920 (PP)

System :SC-HT920 (PC) MusicCenter:SA-HT920 (PC)

SatelliteSpeakers:SB-HT920 (P)

ActiveSubwoofer:SB-WA920 (PP)

1. SafetyPrecautions

1.1. GENERALGUIDELINES

1. Whenservicing, observetheoriginal leaddress. Ifashortcircuit

isfound, replace all parts whichhavebeenoverheatedor

damagedbytheshortcircuit.

2. Afterservicing, see toitthat all theprotectivedevices suchas

insulation barriers, insulation papersshieldsareproperlyinstalled.

3. Afterservicing, make thefollowing leakagecurrentchecks to

preventthecustomerfrombeing exposedtoshock hazards.

(This“SafetyPrecaution”isappliedonlyinU.S.A.)

1. Beforeservicing, unplug thepowercordtopreventanelectric

shock.

2. Whenreplacing parts, use onlymanufacturer’srecommended

components forsafety.

3. Check thecondition ofthepowercord. Replace ifwearordamage

isevident.

4. Afterservicing, besuretorestoretheleaddress, insulation

barriers, insulation papers, shields, etc.

5. Beforereturning theservicedequipmenttothecustomer, besure

tomake thefollowing insulation resistance test topreventthe

customerfrombeing exposedtoashock hazard.

1.1.1. LEAKAGE CURRENTCOLDCHECK

1. Unplug theACcordand connect ajumperbetweenthetwoprongs

on theplug.

2. Measuretheresistance value, withanohmmeter, betweenthe

jumperedACplug and eachexposedmetalliccabinet parton the

equipmentsuchas screwheads, connectors, control shafts, etc.

Whentheexposedmetallicparthas areturnpathtothechassis,

thereading shouldbebetween1M and 5.2 . / Whenthe

exposedmetal does nothaveareturnpathtothechassis, the

reading must be . Fig. 1

1.1.2. LEAKAGE CURRENTHOTCHECK (See Figure1.)

1. Plug theACcorddirectlyintotheACoutlet. Donotuse an

isolation transformerforthischeck.

2. Connect a1.5k , 10 watts resistor, inparallel witha0.15 F

capacitors, betweeneachexposedmetallicparton theset and a

good earthground suchas awaterpipe, as showninFigure1.

3. Use anACvoltmeter, with1000 ohms/voltormoresensitivity, to

measurethepotential across theresistor.

4. Check eachexposedmetallicpart, and measurethevoltageat

eachpoint.

5. Reverse theACplug intheACoutlet and repeat eachoftheabove

measurements.

6. Thepotential at anypointshouldnotexceed0.75 volts RMS. A

leakagecurrenttester(Simpson Model 229 orequivalent) maybe

usedtomake thehotchecks, leakagecurrentmust notexceed1/2

milliamp. Incase ameasurementisoutsideofthelimits specified,

thereisapossibilityofashock hazard, and theequipmentshould

berepairedand recheckedbeforeitisreturnedtothecustomer.

2. Handling the Lead-free Solder

2.1. Aboutleadfree solder(PbF)

Distinction ofPbF P.C.B. :

P.C.B.s(manufactured)using leadfree solderwill have aPbF stampon theP.C.B.

Caution:

-Pbfree solderhas ahighermelting pointthat standardsolder;

Typicallythemelting pointis50 -70°F(30 -40°C)higher. / Please

use ahigh temperaturesoldering iron. Incase ofthesoldering iron

withtemperaturecontrol, please set itto700 ±20°F(370 ±10°C).

-Pbfree solderwill tend tosplashwhenheatedtoo high (about

1100°F/600°C).

-Whensoldering orunsoldering, please completelyremoveall ofthe

solderon thepinsorsolderarea, and besuretoheat thesoldering

points withthePbfree solderuntil itmelts enough.

3. BeforeRepairand Adjustment

DisconnectACpower, dischargePowerSupplyCapacitorsC546, C547, C548, C549 through a10

, 1Wresistor toground.

DONOTSHORT-CIRCUITDIRECTLY(withascrewdriverblade, for instance), as thismay destroy

solidstatedevices.

Afterrepairsarecompleted, restorepowergraduallyusing avariac, toavoidovercurrent.

Currentconsumption atAC120V, 60HzinNOSIGNALmodeshouldbe~1000 mA.

4. Protection Circuitry

Theprotection circuitrymay have operatedifeitherofthefollowing conditionsarenoticed:

-Nosound isheardwhenthepoweristurnedon.

-Sound stopsduring aperformance.

Thefunction ofthiscircuitryistopreventcircuitrydamageif, for example, thepositive and

negative speakerconnection wires are

“shorted”, or ifspeakersystemswithanimpedance less thantheindicatedratedimpedance of

theamplifierareused.

Ifthisoccurs, followtheprocedureoutlines below:

1. Turnoff thepower.

2. Determinethecause oftheproblemand correct it.

3. Turnon thepoweronce againafteroneminute.

Note:

Whentheprotection circuitryfunctions, theunitwill notoperateunless thepowerisfirstturned

off and thenon again.

5. Connection of the SpeakerCables

-Besuretoconnect speakercables beforeconnecting theACpower

supplycord.

-Theloadimpedance ofanyspeakerusedwiththisunitmust be4 .

-Besuretoconnect thecablefromtherightspeakertotheright

terminal and thecablefromtheleft speakertotheleft terminal.

1. Stripoff theoutercovering, and twist thecenterconductor. Make

surethebareendsofthewires arenotunravelled. (Iftheyare,

twist themtightagain.)

2. Insertthewiretotherearpanel oftheunitand close thelever.

Notes :

-To preventdamagetocircuitry, nevershort-circuitpositive(+)and

negative(-) speakerwires.

-Besuretoconnect onlypositive(Copper)wires topositive(+)

terminalsand negative(Silver)wires tonegative(-) terminals.

6. DisassemblyProcedure

“ATTENTIONSERVICER”

Somechassiscomponentsmay have sharp edges.

Becareful whendisassembling and servicing.

1. Thissection describes procedures forchecking theoperation of

themajorprintedcircuitboardsand replacing themain

components.

2. Forreassemblyafteroperation checks orreplacement, reverse the

respectiveprocedures.

Special reassemblyprocedures aredescribedonlywhenrequired.

3. Select itemsfromthefollowing index whenchecks orreplacement

arerequired.

Contents

-DisassemblyoftheSpeakerUnit

-MainComponentReplacementProcedures

6.1. Disassemblyflow chart

Thefollowing chartistheprocedurefor disassembling thecasing and insidepartsfor internal

inspection whencarrying outtheservicing.

Toassembletheunit, reverse thestepsshowninthechartbelow.

6.2. DisassemblyoftheSpeakerUnitand Checking oftheP.C.B.

Step1:Remove all thescrews.

Step2:Remove thestand base.

Steps3&4:Remove all thescrewsfrom thebottom ofthespeakerunit.

Step5:Use theSteel Rulertoslotintotheholeofthebottom cabinetofspeaker.

Step6:Use theWood ChiptoslotbetweentheNetFrameand theSteel Ruleras arrowshown.

Step7:Use theScrewdriverslightlylift up theNetFrameas arrowshown.

Step8:Take noteofthebosses whichgluedtotheunit.

-AssemblyofNet Frame.

Cleanup all theglueatthe4Boss pointsand replace withthenormal glue.

Replace theNetFramefirmlyback intothecabinet.

Step9:Remove theNetFramefrom thecabinetofspeaker.

Table des matières

Autres manuels Panasonic Subwoofer

Panasonic

Panasonic SB-WA330GN Manuel utilisateur

Panasonic

Panasonic SB-W340E Manuel utilisateur

Panasonic

Panasonic SB-WA330E Manuel utilisateur

Panasonic

Panasonic SBW500 - SUBWOOFER SYS Manuel utilisateur

Panasonic

Panasonic SB-W40P Manuel utilisateur

Panasonic

Panasonic SB-WA933 Manuel utilisateur

Panasonic

Panasonic SB-AS40 Manuel utilisateur

Panasonic

Panasonic SB-WA340 Manuel utilisateur

Panasonic

Panasonic SB-WA870EB Manuel utilisateur

Panasonic

Panasonic SB-WA520EB Manuel utilisateur

Panasonic

Panasonic SB-AS100 Manuel utilisateur

Panasonic

Panasonic SB-WA15E Manuel utilisateur

Panasonic

Panasonic SB-WA520GC Manuel utilisateur

Panasonic

Panasonic SB-WA730 Manuel utilisateur

Panasonic

Panasonic Ramsa WS-A240 Manuel utilisateur

Panasonic

Panasonic SB-WA100 Manuel utilisateur

Panasonic

Panasonic SBAS500 - SPKR,ACTIVE SUBWOOFE Manuel utilisateur

Panasonic

Panasonic SB-WA730GCP Manuel utilisateur

Panasonic

Panasonic SB-WA800 Manuel utilisateur

Panasonic

Panasonic SB-WA17E Manuel utilisateur

Panasonic

Panasonic SB-WA530EB Manuel utilisateur

Panasonic

Panasonic SB-WA733P Manuel utilisateur

Panasonic

Panasonic SB-WA880 Manuel utilisateur

Panasonic

Panasonic SB-WA730GCP Manuel utilisateur

Manuels Subwoofer populaires d'autres marques

Sony

Sony XS-AW8 Manuel utilisateur

Sony

Sony XS-L836 Manuel utilisateur

B&C Speakers

B&C Speakers 15 HPL 76W Manuel utilisateur

Velodyne

Velodyne DD-18+ Manuel utilisateur

Sonance

Sonance Cinema Series SUB 10-150 Manuel utilisateur

Hifonics

Hifonics HW-12 Guide de démarrage rapide

Magnat Audio

Magnat Audio ADR 130 BP Manuel utilisateur

Blitz

Blitz BZP106 Manuel utilisateur

Technics

Technics SB-AS500 Manuel utilisateur

Lyngdorf

Lyngdorf BW-2 Manuel utilisateur

Lyngdorf

Lyngdorf BW-3 Manuel utilisateur

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manuel utilisateur

REL Acoustics

REL Acoustics Q Series Manuel utilisateur

Pioneer

Pioneer Elite S-W1EX Manuel utilisateur

L-Acoustics

L-Acoustics KIVA SB15M Guide de démarrage rapide

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manuel utilisateur

KEF

KEF KUBE 200 Manuel utilisateur

Yamaha

Yamaha SW500 Manuel utilisateur