Panasonic SC-H M900 Manuel utilisateur

ROZMO121

Service Manual

SC-HM900

SB-PS70

SB-HM900 SA-HM900

Stereo system

SC-H M900

SB-HM900

ESPECIFICA TIONS

r'-

Notes:

1. AIIthe informationaresubjecttochangewithoutnotice.

2. Weigthanddimensionsareapproximate.

,...... Panasonic (illol!@

DIGITAL AUDIO

MODEL UNIT

SA-HM900 Stereo

SC-HM900 SB-HM900 Front Speaker

SB-PS70 Surround Speaker

SB-PC70 Cantar Speaker

POWEROUTPUT(AMPLlFIER)

Front (Low) 130W RMS par ehannel (6 Q), 80 Hz , 10% DAT

(High) 70 W RMS par ehannel (6 Q), 1 kHz , 10% DAT

Surround 50W RMS par ehannel (8 Q), 1 kHz, 10% DAT

Central 100W RMS (8Q), 80 Hz, 10 % DAT

AMPlIFIER SA-HM900

Power output: 7000 W PMPO

Power eonsumption: 280 W

Supply: 127V ea :t10% 60 Hz

Input sensitivity: 250 mV

Freeueney ranga AM: 522 - 1629 kHz (9 kHz steps )

520 -1630 kHz (10kHz steps)

Freeueney ranga FM: 87,5 - 108,0 MHz (50 kHz steps )

Dimensions (b x h xl): 360 x 425 x 340 mm

Weight: 9,8 kg approx.

SC-HM900 I

"""'"

Lh WARNING

This service information is designed for experienced repair technicians only and is not designed for use bythe general

publico

It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to

service a product. Producís powered by electricity should be serviced or repaired only by experienced professional

technicians. Any attempt to service or repair the porduct or producís dealt with in this service information by anyone

else could result in serious injury or death. ~

CONTENTS

page

Safety Precaution 3

Before Repair and Adjustment 4

Protection Circuitry 4

Accessories 4

Handling Precautions For Traverse Deck 5

Precaution of Laser Diode '6

Operation Procedures""""""" 7

Operation Checks and Main Component Replacement Procedures 9

Self-Diagnostic Function """""' 17

Descriptionof ErrorCede"""""""" 18

Cd Test Mode Function """"""""""" 19

Measurements and Adjustments """"""' 20

lIIustration of IC, Transistors and Diodes :23

Terminal Function of IC 24

Block Diagram "" 27

Schematic Diagram 35

Printed Circuit Board 48

Wiring Connection Diagram """""""' 59

TroubleshootingGuide"""""""""" 60

París Location and Replacement París List 61

- 2-

PSPEAKERS INPUT DIMENSIONS WEIGHT

IMPEDANCE (b x h x 1)

SB-HM900

FRONT 355 x 560 x 340 mm 9,2 Kg aprox.

Super Tweeter 3cm - - - - -- -- -

Tweeter 6cm - -- -- - - - -

Woofer 17 cm - -- -- - - - -

Super Woofer 30 cm - -- - - - -- -

(high) 612 - - - -- -

(Iow) 612 - - - -- -

SB-PS70

SURROUND

FuI!Range 8 cm 812 170 x 106x 118 mm 0,9 Kg aprox.

SB-PC70

CENTER 812 250x121 x147mm 1,6 Kg aprox.

Tweeter 6cm

Woofer 10 cm A

,.-.

,.....

,......

r---

1SC-HM900

1Safety Precaution

Before Servicing, unplug the power cord to prevent an electric shock.

When replacing parts, use only manufacture's recommended components for safety.

Check the condition of the power cardoReplace if wear or damage is evident.

After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.

Before returningthe serviced equipment to the customer, be sure to make the following insulation resistance test to

prevent the customer from being exposed to a shock hazard.

1.1 Insulation Resistance Test

Unplug the power cord and short the two prongs of the plug with a jumper wire.

Turn on the power switch.

Measure the resistancevalue with ohmmeter between thejumper AC plug and each exposed metal cabinet part, such

as screwheads, antenna, control shafts, handle brackets, etc.

Equipment with antenna terminals should read between 3MQ and 5.2MQ to all exposed parts* (Fig.1).

Equipment without antenna terminals should read approximately infinity to all exposed parts. (Fig.2).

*Note: Some exposed parts may be isolated from the chassis by designoThese will read infinity.

4. If the measurement is outside the specified limits, there is a possibility of a shock hazard. The equipment should be

repaired and rechecked before it is returned to the customer.

Exposed

metal,./'/

par!

Fig.1

Resistance ==3MO - 5.2MO

Exposed

metal/'

par!

Fig-:2

Resistance==Approx 00

- 3-

SC-HM900 J

2Before Repair and Adjustment

Disconnect AC power, discharge Power Supply Capacitors POWER PCB C556, C557, C558, C559, C561 and TRANS-

FORMER PCB C705 through a 10 Q, 5W resistorto ground.

DO NOT SHORT-CIRCUIT DIRECTLy (with a screwdriver blade, for instance), as this way destroy salid state devices.

After repairs are completed, restore power gradually using a variac, to avoid overcurrent.

'"'

Current consumption at AC 127V, 60Hz in NO SIGNAL mode should be ~800mA.

3Protection Circuitry

The protection circuitry may have operated if either of the following conditions are noticed.

.No sound is heard when the power is turned on.

Sound stops during a performance.

The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection

wires are "shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are

used.

If this occurs, follow the procedure outlines below:

Turn off the power.

Determine the cause of the problem and correGíit.

Turn on the power once again after one minute.

Note:

Whentheprotectioncircuitryfunctions,theunitwillnotoperateunlessthepowerisfirstturnedoffandthenonagain.

4Accessories '""

Ac cord 1 pza

(SJA168-1A) DtR~~~~~~~)""""""""""""""""""""" 1 pza

Df~s~~~~~-~)""""""""""""""""""""" 1 pza DBattery(remote control) 2 pzas

(UM-3PA)

DtRMM~~~~~~support 1 pza D ~~2~ol~~~~~~113)""""""""""""""""" 1 pza

,..-".

-4-

[SC-HM900

5Handling Precautions For Traverse Deck

f'" The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity

of clothes or human body.

So. be careful of electrostatic breakdown during repair of the traverse deck (optical pick up).

Handling of traverse deck (optical pick up)

1. Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock.

2. The short land between the No. 4 (LO)and No. 5 (GND)pins on the flexible board (FFC) is shorted with a solde build-

up to prevent damage tothe laserdiode. To connect to the PC board besure to open by removing the solder build-up

and finish the work quickly.

3. Take Gafenot to apply excessive stress to the flexible board (FFC).

4. Do not turn the variable resistor (laser power adjustment). It has already been adjusted.

Flexible board.

FFC

(Handle it carefully)

Lens

(Donottouch)

,~/

No.@Pin(GND) No.@)Pin(LO) Variable resistor

(Do not lum)

Grounding for electrostatic breakdown prevention

1. Human body groundling

Use the anti-satatic wrist strap to discharge the static electricity from your body.

Work table grounding

Pul a conductive material (sheet) or steel sheet on the afea where the traverse deck (optica! pickup) isplaced, and

ground the sheet.

r2.

Caution:

The static electricity of your clothes will not be groundedthrough the wrist strap. So,take Gafenot to leí your clothes touch

the traverse deck (optical pickup).

Caution when Replacing the Traverse Deck:

The traverse deck has a short point shourted with solder to proteGíthe lazer diode against electrostatics breakdown. Be

sure to remove the solder from the short point before making connections.

,.....

Wriststrap

(Anti-static bracelet)

Iron plate or some metals

to conduct electricity

- 5-

SC-HM900]

6Precaution 01 Laser Diode

CAUTION:

This unit utilizes a class 1 laser.

Invisible laser radiation is emitted from the optical pick up lens.

When the unit is turned on:

1. Do not look directly into the pick up lens.

2. Do not use optical instruments to look at tlle pick up lens.

3. Do not adjust the preset variable resistor on the pick up lens.

4. Do not disassemble the optical pick up unit.

5. If the optical pick up is replaced use the manufactures's specified replacement pick up only.

6. Use of control or adjustments or performance of procedures other than those specified here in may result in hazard-

ous radiation exposure.

'1"""'\

CAUTION!

THIS PRODUCT UTILlZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI

FIED HERE IN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

-"""

"""'"

" ,.

- 6-

...

7Operation Procedures

..........

r101

""",,, I ",,"m, ,"",,'O"

ISC-HM900

aMain unit

No. Name

CD Ac supply indicator (AC IN)

(This indicalor lighls when Ihe unil is connecled lo Ihe AC power supply)

(]) Standby/on switch (6/1 POWER)

Press lo switch Ihe unil Irom on lo slandby mode or viceversa. In slandby

mode, Ihe unil is slill consuming a small amounl 01 power.

@ Play timer/record timer button (e) PLAY/ e) REC)

@ Clock/timer button (CLOCKlTIMER)

@ Signal sensor

@ 6ch button (6 CH INPUT)

(j) Karaoke select button KARAOKE

@ Microphone volume control (MIC VOL)

@ Microphone jacks 1 y 2

@ Deck 1 open button ( ~ DECK 1 OPEN)

@ Deck 1 cassette holder

@ Disc tray

@ Cd manager button (CD MANAGER)

@J Disc direct play and indicators (1 - 5)

@ Disc tray open/close button ( ~ )

@ Super 3d ai button (SUPER 3D Al)

@ Super sound eq button (SUPER SOUND Ea)

@ Sound equalizer knob (SOUND Ea)

@ Sound equalizer control (SOUND Ea)

@ Volume control (VOLUME DOWN UP)

@ Headphones jack (PHONES)

~Deck 2 open button ( ~ DECK 2 OPEN)

eDeck 2 cassette holder

rn Consola central

~Aux select button (AUX 1/2)

@ Tuner/band select button (TUNER BAND)

@ Tape/deck select button (DECK 1/2 TAPE)

@ Cd button (CD)

@ Display

@ Reverse mode select button (REV MODE)

@ Tape edil button (TAPE EDIT)

@ Dolby pro logic button ( [][JPRO LOGIC)

@ Display selectldemostration button (-DISPLAY/-DEMO)

@ Recording button ( . REC/STOP)

@ Surround button (SURROUND)

@ Super woofer on/off button (S. WOOFER)

@ Basic operating button

(Funclions change according lo Ihe source)

- 7-

SC-HM900 ]

IRemote control

Numberssuch asO, lunction is exactlythe same way as the buttons on

the main unit and the number such as @, lunction only with remate

control.

""'""

No. Nombre

f) Standby/on button ( <!>)

@Auto power-off (AUTO OFF)

@Numeric buttons (;::: 10,1-9, O)

@Program button (PROGRAM)

@Cancel button (CANCEL)

~Aux selector button (AUX 1/2)

eTuner/band select button (TUNER)

G) Eq select button (Ea)

e3d ai button (3D Al)

a. Dolby Pro Logic button ([][] PL)

@Play/pause/preset channel select button (only lor cd play)

(""/11IV )

@Test button (TEST)

@Channel selector button (CH SELECT)

G> Volume buttons (- VOLUME +)

@Sleep button (SLEEP)

@Muting button (MUTING)

@Disc button (DISC)

@Random button (RANDOM)

@Repeat button (REPEAT)

GDisc button (CD)

eTape/deck selct button (TAPE)

@Skip/search bullan ( 1+11/"-, ~/~ )

@Play/preset channel select ( ~/¡\)

~Stop/clear program melodies (8/CLEAR)

@Channellevel selector buttons (- CH LEVEL +)

""'"

'"'"

"--

,........

, ,.,

- 8-

ISC-HM900

8Operation Checks and Main Component Replacement

Procedures

r"'-

IGear for servicing (jig) informationI

1. This unít has a gear which is usedfor checking items (open/close of disc tray, up/down operation of traverse unit by

manually) when servicing.

2. For preparation of gear (for servicing), Perform the procedures as follows.

3. In case of re-servicingthe same gel, the "gear for servicing" may has been taken off because ithas been used.

The "gear for servicing" must be stored.

1. Remove the gear provided with mechanism cover

as shown below. 2. Insertthe hexagonal screwdriver (2 mm) into the

gear and then project the tip of screwdriver for

1~2mm in length.

~t-

Gear ~.

nHexagonal screwdnver

VIPart No. : SZZP11 0.1C]

Mechanism caver -1~

1-2mm

c=:

"ATTENTION SERVICER"

Some chassis components may have sharp edges.

Be careful when disassembling and servicing.

1. This section describes procedures for checking the operation of the majar printed circuit boards and replac-

ing the main components.

For reassembly alter operation checks or replacement, reverse the respective procedures.

Special reassembly procedures are described only when required.

3. Select items from the following index when checks or replacement are required.

Contents

eDisassemblyandassemblymain unit

1. Checking of the Main, Panel, Deck and Power P.C.B.

Main component Replacement Procedures

1. Replacementof the Traverse Deck.

2. Replacement of the PowerAmplifier IC.

eDisassemblyand assemblyof theTraverseUnit

eDisassemblyandassemblyof the DiscTray

Warning:

This product uses a laser diode. Refer to caution statement Precaution of Laser Diode.

- 9-

SC-HM900 I

8.1 Disassembly and assembly main unit

Step 1 Remove 4 screws each side and remove

the Top Gabinet.

E)x 4

Step 3 Pul!out the CD tray as shown and remove

the CD lid. Push back the CD tray after the

CD lid has been removed.

Step 2 To open the CD tray, releasethe le-

ver as shown.

E)x 4

Step 4 Remove the screws.

"'""'

0x 16 .......

- 10-

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Système stéréo

Panasonic

Panasonic SC-BTT885 Manuel utilisateur

Panasonic

Panasonic RX-ES23 Manuel utilisateur

Panasonic

Panasonic SA-MAX370GS Manuel utilisateur

Panasonic

Panasonic SC-PMX9 Manuel utilisateur

Panasonic

Panasonic SA-AK230GCP Manuel utilisateur

Panasonic

Panasonic SC-AK57 Manuel utilisateur

Panasonic

Panasonic SA-PMX82M Manuel utilisateur

Panasonic

Panasonic SC-MAX8700 Manuel utilisateur

Panasonic

Panasonic SC-C39 Manuel utilisateur

Panasonic

Panasonic SC-PM500DB Manuel utilisateur

Panasonic

Panasonic RX-CS710 Manuel utilisateur

Panasonic

Panasonic RXDS750 - RADIO CASSETTE W/CD Manuel utilisateur

Panasonic

Panasonic RX-DU10 Manuel utilisateur

Panasonic

Panasonic SCPM25 - CD STEREO SYSTEM Manuel utilisateur

Panasonic

Panasonic SA-AK870GCP Manuel utilisateur

Panasonic

Panasonic RX-DS22 Manuel utilisateur

Panasonic

Panasonic SA-VKX80GA Manuel utilisateur

Panasonic

Panasonic SA-PM31P Manuel utilisateur

Panasonic

Panasonic SA-AKX220PN Manuel utilisateur

Panasonic

Panasonic SA-PM45PC Manuel utilisateur

Panasonic

Panasonic SA-PM18E Manuel utilisateur

Panasonic

Panasonic SCPM22 - CD STEREO SYSTEM Manuel utilisateur

Panasonic

Panasonic SC-AK47 Manuel utilisateur

Panasonic

Panasonic SA-AK580 Manuel utilisateur

Manuels Système stéréo populaires d'autres marques

LG CM3330B Manuel utilisateur

Sony

Sony SS-CEP50 Manuel utilisateur

Cetacea Sound

Cetacea Sound CVS-II Manuel utilisateur

Aiwa

Aiwa XR-H66MD Manuel utilisateur

Denon

Denon UCD-250 Manuel utilisateur

Sanyo

Sanyo DC-MX41i Manuel utilisateur

Sharp

Sharp CD-ES600V Manuel utilisateur

Exibel

Exibel BDX600-UK Manuel utilisateur

Sanyo

Sanyo DC-F320 Manuel utilisateur

Philips

Philips FWM583X Manuel utilisateur

Sharp

Sharp CD-C462 Manuel utilisateur

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Manuel utilisateur

Aiwa

Aiwa XR-EM70 Manuel utilisateur

Cyrus

Cyrus Lyric Manuel utilisateur

Philips

Philips MCM159/98 Manuel utilisateur

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Manuel utilisateur

RCA

RCA RS3965SB Manuel utilisateur

Sharp

Sharp XL-UH240 Manuel utilisateur