Panasonic WVCS854 - COMBINATION CAMERA Mode d’emploi

Installing PTZ Cameras

on a DVX system

Panasonic WV-CS854 Dome

External RS-485 Control

June 2002

#3000-40046 Rev. 2

Installing PTZ Cameras on a DVX system

June 2002

Page

Installing Panasonic WV-CS854 on a DVX system

To use a Panasonic WV-CS854 camera with a DVX system , you must wire the camera to the RS-485 converter, and then

plug the converter into the COM port on the DVX system. The A pin must be connected to the orange T and yellow R wires

from the camera, and the COM B pin must be connected to the red T and green R wires from the camera:

RS-485 converter pin Panasonic 5-wire terminal

COM A Orange T (A)

COM B Red T (B)

COM A Green R (A)

COM B Yellow R (B)

The following figure illustrates the connection points between the DVX system and the camera. (Drawing not to scale; DVX

drawing may not match your particular DVX model.)

SW1 SW2

OFF

DVX System

External RS-485 converter

7 to 12 VAC/DC

power adapter

PWR

COM A

COM B

Red T (B)

Yellow R (B)

Orange T (A)

Green R (A)

Panasonic WV-CS854

On the Setup page in

MasterControl, make sure

you select COM1 on the PTZ

tab for this camera.

Installing PTZ Cameras on a DVX system

June 2002

Page

Panasonic WV-CS854: Setup Instructions

The figure on the previous page shows the SW1 switch used to select the protocol, communication parameter, and camera

address. You must set this switch three times, as described in the following instructions:

1. Select the protocol by setting SW1 as follows (factory default settings):

12345678

OFF ON OFF ON ON OFF OFF OFF

2. Insert the camera in its mount and wait for the camera to complete the startup sequence.

3. Remove the camera from its mount.

4. Select the communication parameters (9600bps, data bit 8, parity check N, stop bit 1) by setting SW1 as follows:

12345678

OFFONONONONOFFOFFOFF

5. Insert the camera in its mount and wait for the camera to complete the startup sequence.

6. Remove the camera from its mount.

7. Select a unique camera address from 1 to 32 by setting SW1 as follows (note that 8 is ON in each case):

Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

1 ON OFF OFF OFF OFF OFF OFF ON

2 OFF ON OFF OFF OFF OFF OFF ON

3 ON ON OFF OFF OFF OFF OFF ON

4 OFF OFF ON OFF OFF OFF OFF ON

5 ON OFF ON OFF OFF OFF OFF ON

6 OFF ON ON OFF OFF OFF OFF ON

7 ONONONOFFOFFOFFOFFON

8 OFF OFF OFF ON OFF OFF OFF ON

9 ON OFF OFF ON OFF OFF OFF ON

10 OFF ON OFF ON OFF OFF OFF ON

11 ON ON OFF ON OFF OFF OFF ON

12 OFF OFF ON ON OFF OFF OFF ON

13 ON OFF ON ON OFF OFF OFF ON

14 OFFONONONOFFOFFOFFON

15 ON ON ON ON OFF OFF OFF ON

16 OFF OFF OFF OFF ON OFF OFF ON

17 ON OFF OFF OFF ON OFF OFF ON

18 OFF ON OFF OFF ON OFF OFF ON

19 ON ON OFF OFF ON OFF OFF ON

20 OFF OFF ON OFF ON OFF OFF ON

21 ON OFF ON OFF ON OFF OFF ON

22 OFF ON ON OFF ON OFF OFF ON

23 ON ON ON OFF ON OFF OFF ON

24 OFF OFF OFF ON ON OFF OFF ON

25 ON OFF OFF ON ON OFF OFF ON

26 OFF ON OFF ON ON OFF OFF ON

27 ON ON OFF ON ON OFF OFF ON

28 OFF OFF ON ON ON OFF OFF ON

29 ONOFFONONONOFFOFFON

30 OFFONONONONOFFOFFON

31 ON ON ON ON ON OFF OFF ON

32 OFF OFF OFF OFF OFF ON OFF ON

8. Insert the camera in its mount and wait for the camera to complete the startup sequence.

Installing PTZ Cameras on a DVX system

June 2002

Page

1234

OFFONONON

1234

ON ON ON ON

Panasonic WV-CS854: Camera Termination

The figure on page 2 shows the location of the SW2 switch, which is used to select the termination (switch 1) and duplex

setting (switches 2–4, half duplex). Complete the following instructions:

1. Remove the camera from its mount.

2. Set SW2 as follows if the camera is not the final camera in a chain:

3. Set SW2 as follows if the camera is the final camera in a chain:

See the Panasonic WV-CS854 installation manual for more information.

Panasonic WV-CS854: Connecting Multiple Cameras

Additional cameras are connected to the DVX system in a daisy chain, star, or combination configuration; the final camera in

each chain must be terminated. Each camera must have a unique address that matches the video input number it is connected

to on the DVX system (see the DVX user manual). Sample configurations are shown in the following figure.

See the camera manufacturer’s installation manual for more information.

DVX

Address: 1 Address: 2 Address: 3 (terminate)

DAISY CHAIN

DVX

Address: 1

Address: 2

Address: 3

(terminate)

STAR

DVX

Address: 1

Address: 3

Address: 5

Address: 2 (terminate)

Address: 4 (terminate)

Address: 6 (terminate)

COMBINATION

Installing PTZ Cameras on a DVX system

June 2002

Page

Enabling COM Ports (Upgrade Situtations Only)

When upgrading an existing DVX system to enable PTZ capability, you must enable the COM ports on the DVX system. To

verify that the COM ports are enabled on your system, view the PTZ tab on the Setup page in MasterControl on the DVX

system. If the COM ports are not enabled, the following message is displayed on the PTZ tab:

Unable to detect COM ports on your system. You must install a COM port

to use PTZ cameras.

If this message appears, you must enable the COM (serial) ports in the system BIOS. For assistance, please contact the

Technical Support Center at 1-720-872-9100.

NOTE: The PTZ tab is available in MasterControl only if you have entered a valid PTZ license key. See the front page of

this document for details.

Autres manuels Panasonic Caméra de sécurité

Panasonic

Panasonic EggCam GP-KR001 Manuel utilisateur

Panasonic

Panasonic WV-CP500/G Manuel utilisateur

Panasonic

Panasonic WV-S1570L Manuel d'utilisation

Panasonic

Panasonic WVCL920 - COLOR CAMERA Manuel utilisateur

Panasonic

Panasonic WVCW474F - COLOR CCTV CAMERA Manuel utilisateur

Panasonic

Panasonic WV-SFV311 Manuel utilisateur

Panasonic

Panasonic WV-SFR311 Manuel utilisateur

Panasonic

Panasonic WV-SW458 Manuel utilisateur

Panasonic

Panasonic K-EW114L03E Manuel utilisateur

Panasonic

Panasonic WV-CP470 Series Manuel utilisateur

Panasonic

Panasonic WV-SFR631L Manuel utilisateur

Panasonic

Panasonic BL-VT164W Manuel utilisateur

Panasonic

Panasonic HX-A1M Instructions d'installation et d'entretien

Panasonic

Panasonic WV-CF284 Series Manuel utilisateur

Panasonic

Panasonic BB-HCM547A Manuel utilisateur

Panasonic

Panasonic AWHE60H Manuel utilisateur

Panasonic

Panasonic WV-SW458 Manuel utilisateur

Panasonic

Panasonic WV-SW458 Manuel utilisateur

Panasonic

Panasonic KX-HCM280 Manuel utilisateur

Panasonic

Panasonic WV-SPV781L Manuel utilisateur

Panasonic

Panasonic WVNP1000 - NETWORK CAMERA Manuel utilisateur

Panasonic

Panasonic PI-BUA3MWA Manuel utilisateur

Panasonic

Panasonic WV-CF224 Manuel utilisateur

Panasonic

Panasonic AKHC3500 - MULTI FORMAT CAMERA Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur