Panasonic K-EW114L01E Manuel utilisateur

HD IR Vari-Focal Fixed Network Camera

Quick Start Guide

Model No. K-EW114L01E

Version 1.0.0

Welcome

Thank you for purchasing our network camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

．

Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please

note: Do not connect two power supplying sources to the device at the same time; it may result

in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

．

Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

．

Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

．

Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

．

Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,

inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

Thunder-proof device is recommended to be adopted to better prevent thunder.

The grounding studs of the product are recommended to be grounded to further enhance the reliability

of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

Dome enclosure is the optical component, do not touch the enclosure when you are installing the

device or clean the enclosure when you are doing maintenance work. Please use professional optical

clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result

in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

Network Camera Unit 1

Quick Start Guide 1

Installation Accessory Bag 1

CD 1

iii

Table of Contents

1Framework................................................................................................................................... 1

1.1 Device External Cable ................................................................................................. 1

1.2 Framework and Dimension......................................................................................... 2

2Device Installation ...................................................................................................................... 3

3Quick Configuration Tool........................................................................................................... 5

3.1 Overview........................................................................................................................ 5

3.2 Operation ....................................................................................................................... 5

4Web Operation ..............................................................................................................7

4.1 Network Connection..........................................................................................7

4.2 Login and Main Interface...................................................................................7

Framework

1.1

Device External Cable

You can refer to the following figure for device external cable information. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

SN Port Port Name Connection Note

1 LAN Network port Ethernet

port

Connect to standard Ethernet cable.

Note:

Before making crystal head, pull the

anti-dust cover (default), waterproof

cover (optional) through network

cable.

2 DC 12V Power input

port - Power port. Input DC 12V.

1.2

Framework and Dimension

Please refer to the following figure for dimension information. The unit is mm. See Figure 1-2 and

Figure 1-3.

Figure 1-2 Dimension illustration 1

Figure 1-3 Dimension illustration 2

Device Installation

Important

•

Make sure that the installation area is strong enough to hold the product, such as a

concrete ceiling.

•

Install the camera in the foundation area of the architecture or where sufficient strength

is assured.

•

If a wall or ceiling board such as plasterboard is too weak to support the total weight,

the area shall be sufficiently reinforced.

Please see Figure 3-1 and Figure 3-2.

Step 1

Open accessories bag, take out installation position map and stick it to designated surface where

you will install the device (wall or ceiling).

Step 2

Dig a hole according to position of hole on installation position map.

Step 3

Remove the installation template label and attach the camera with 3 screws (locally procured).

Step 4

Plug external wiring of the device properly.

Figure 2-1

Figure 2-2

Step 5

Use inner hex screwdriver to loosen adjusting screw shown in Figure 2-2.

Step 6

Adjust the device in all possible directions, and set its monitoring direction.

Then, please adjust the viewing angle and focus.

Notes:

・Viewing angle and focus adjustments shall be performed together with camera angle

adjustment.

・Refer to the operation manual (included in the CD-ROM) for how to perform the zoom and

focus settings from system menu.

Quick Configuration Tool

3.1

Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you

can use it to upgrade the device.

Please note the tool only applies to the IP addresses in the same segment.

3.2

Operation

Step 1

Double click the “ConfigTools.exe” icon; you can see an interface is shown as in Figure 3-1.

In the device list interface, you can view device IP address, port number, subnet mask, default

gateway, MAC address and etc.

Step 2

Select one IP address and then right click mouse, you can see an interface is shown as in Figure

3-2. Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 3-1 Search interface

Figure 3-2 Search interface 2

Step 3

If you want to modify the device IP address without logging in the device web interface, you can

go to the configuration tool main interface to set.

In the configuration tool search interface (Figure 3-1), please select a device IP address and then

double click it to open the login interface. Or you can select an IP address and then click the

In Figure 3-3, you can view device IP address, user name, password and port. Please modify the

corresponding information to login.

Please note the port information here shall be identical with the port value you set in TCP port in

Web Network interface. Otherwise, you cannot login the device.

If you are using device background upgrade port 3800 to login, other setups are all invalid.

After you logged in, the configuration tool main interface is shown as below. See Figure 3-4.

Figure 3-3 Login prompt

Figure 3-4 Main interface

For detailed information and operation instruction of the quick configuration tool, please

refer to the Quick Configuration Tool User’s Manualincluded in the resources CD.

Autres manuels pour K-EW114L01E

Table des matières

Autres manuels Panasonic Caméra de sécurité

Panasonic

Panasonic AWE300 - COLOR CAMERA Manuel utilisateur

Panasonic

Panasonic K-EF234L01E Manuel utilisateur

Panasonic

Panasonic WV-S15700-V2L Series Manuel utilisateur

Panasonic

Panasonic WV-SP508 Manuel utilisateur

Panasonic

Panasonic i-pro WV-NP1004 Manuel utilisateur

Panasonic

Panasonic BB-HCM311 Manuel utilisateur

Panasonic

Panasonic WV-X6531N Manuel utilisateur

Panasonic

Panasonic WV-SF549 Manuel utilisateur

Panasonic

Panasonic BB-HCM580 Manuel utilisateur

Panasonic

Panasonic BL-C30A - Wireless 802.11 b/g Network Camera Mode d’emploi

Panasonic

Panasonic BL-VT164WBR Manuel utilisateur

Panasonic

Panasonic BB-HCM381A - Network Camera Manuel utilisateur

Panasonic

Panasonic WV-SFV531 Manuel utilisateur

Panasonic

Panasonic WV-SW175 Manuel utilisateur

Panasonic

Panasonic WV-CW504SE Manuel utilisateur

Panasonic

Panasonic KX-HCM230 Manuel utilisateur

Panasonic

Panasonic WVNM100 - NETWORK COLOR CAMERA Manuel utilisateur

Panasonic

Panasonic K-EF134L02AE Manuel utilisateur

Panasonic

Panasonic WV-SW352 Manuel utilisateur

Panasonic

Panasonic WV-BP50E Manuel utilisateur

Panasonic

Panasonic BL-C111 Manuel d'utilisation

Panasonic

Panasonic WV-SW175 Manuel utilisateur

Panasonic

Panasonic WV-SW559 Manuel utilisateur

Panasonic

Panasonic K-EF134L02E Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur