Panasonic K-EF134L02E Manuel utilisateur
HD IR Weatherproof Network Dome Camera
Quick Start Guide
Model No. K-EF134L02E
K-EF134L03E
K-EF134L06E
Version 1.0.2
i
Welcome
Thank you for purchasing our network camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Before your operation please read the following instructions carefully.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated DC12V in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time;
it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (MOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (MOS) optical component damage.
Please keep the sound ventilation.
Thunder-proof device is recommended to be adopted to better prevent thunder.
ii
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily
maintenance work.
Do not touch the CCD (MOS) optic component. You can use the blower to clean the dust on the
lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water
to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to
clean the device.
Please put the dustproof cap to protect the CCD (MOS) component when you do not use the
camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional
optical clean method to clean the enclosure. Improper enclosure clean method (such as use
cloth) may result in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation template label
1
CD
1
Important Safety Instructions
1
iii
Table of Contents
1Structure ......................................................................................................................................1
1.1 Components..................................................................................................................1
1.2 Framework and Dimension.........................................................................................2
2Device Installation ......................................................................................................................3
2.1 Installation Steps for Plastic Dome............................................................................3
2.2 Restore Factory Default Setup Introduction.............................................................5
3Quick Configuration Tool...........................................................................................................6
3.1 Overview........................................................................................................................6
3.2 Operation.......................................................................................................................6
4Web Operation............................................................................................................................8
4.1 Network Connection.....................................................................................................8
4.2 Login and Main Interface.............................................................................................8
1
1Structure
1.1 Components
You can refer to the following figure for multiple-function combination cable information. See Figure
1-1.
Figure 1-1 Multiple-function combination cable
No.
Portname
Function
Connection
Note
4
LAN
Network
port
Ethernet
To connect to standard
Ethernet cable.
5
DC12V
Power input
port
Power input port. Input DC
12V.
No.
Component Name
1
Device lens
2
Dome body
3
Dome enclosure
3
2Device Installation
Important
•Make sure that the installation area is strong enough to hold the product, such as a concrete
ceiling.
•Install the camera in the foundation area of the architecture or where sufficient strength is
assured.
•If a wall or ceiling board such as plasterboard is too weak to support the total weight, the area
shall be sufficiently reinforced.
Please see Figure 2-1 and Figure2-2.
2.1 Installation Steps for Plastic Dome
Please follow the steps listed below to install the device. Please refer to Figure 2-1 for reference.
Step 1
Rotate decoration ring clockwise and take it out.
Step 2
Affix the installation template label (accessory) to the ceiling or wall, and use a pen to mark the
positions of the screws and cable mounting hole in the ceiling or wall. Remove the installation template
label and attach the camera with 3 screws (locally procured).
Step 3
Loosen the M3X8 cross pan head screw on pedestal, and be careful do not loosen completely. Now
you can adjust position according to monitoring area. After adjustment, fasten the M3X8 cross pan
head screw with sheeting.
Step4
Rotate decoration ring bottom up and face the three spigots toward the three slots. When you hear a
“Ca” sound, it is rotated in place.
Figure 2-1 Device installation illustration 1
4
Important
Please pay attention to the dome camera direction when you are installing. Please refer to the
following figure for detailed information. See Figure 2-2.
Figure 2-2 Device installation illustration 2
Note
This series product supports two cable exits. One is from the bottom and the other is from the
side. Please refer to the following figure for cable exit from the side information.
Figure 2-3 Device installation illustration 3
5
2.2 Restore Factory Default Setup Introduction
Important
Please use RESET button when device is running.
Step1
Please refer to step1 and step2 in chapter 2.1 to loose the dome body. Push a little bit; you can take
the dome body from the gland cover.
Step2
Take the dome body out and then turn the top cover hard to remove.
Step3
Slightly press the RESET button to complete the reset function. See Figure 2-4.
Step4
Turn the top cover back to the original position. Please make sure it reaches the original position,
otherwise it may result in water leakage!
Step5
Put the dome back to the gland cover. Please refer to step4 in chapter 2.1 to install the decoration ring
back.
Figure 2-4 Reset
6
3Quick Configuration Tool
3.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
3.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 3-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 3-1 Search interface 1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 3-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 3-2 Search interface 2
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Panasonic Caméra de sécurité
Panasonic
Panasonic AK-HC1500 Manuel utilisateur
Panasonic
Panasonic HomeHawk KX-HNC800 Manuel utilisateur
Panasonic
Panasonic BL-C140 Manuel utilisateur
Panasonic
Panasonic KX-HCM280 Manuel utilisateur
Panasonic
Panasonic BB-HCM381 Manuel utilisateur
Panasonic
Panasonic WVNM100 - NETWORK COLOR CAMERA Manuel utilisateur
Panasonic
Panasonic WV-CS850A Manuel utilisateur
Panasonic
Panasonic BB-HCM381 Mode d'emploi
Panasonic
Panasonic BB-HCM331 Manuel utilisateur
Panasonic
Panasonic WV-NW484SE Guide de l'utilisateur
Panasonic
Panasonic WV-CL930 Series Manuel utilisateur
Panasonic
Panasonic WV-NF284 - i-Pro Network Camera Manuel utilisateur
Panasonic
Panasonic WV-CW324LE Series Manuel utilisateur
Panasonic
Panasonic OneHome BB-HCM331A Manuel utilisateur
Panasonic
Panasonic KX-HNC200 Manuel utilisateur
Panasonic
Panasonic WV-SW175 Manuel utilisateur
Panasonic
Panasonic WV-CF400 Manuel utilisateur
Panasonic
Panasonic WV-CF300L Series Manuel utilisateur
Panasonic
Panasonic AW-HN40HWP Manuel utilisateur
Panasonic
Panasonic aw-he40 series Manuel utilisateur
