Panasonic Panaboard UB-5310 Manuel utilisateur

Electronic Board

Installation Manual

(for qualified service personnel)

Model No. UB-5310

English . . . . . . . . . . . . . . . . . 1–20

Français . . . . . . . . . . . . . . . . 21–40

Deutsch . . . . . . . . . . . . . . . . 41–60

Español . . . . . . . . . . . . . . . . 61–80

Italiano . . . . . . . . . . . . . . . . 81–100

Nederlands. . . . . . . . . . . . . 101–120

Svenska . . . . . . . . . . . . . . . 121–140

中文 . . . . . . . . . . . . . . . . . 141–160

Русский . . . . . . . . . . . . . . . 161–180

Stand kit is optional.

[Stand (option)] [Wall-mounting]

English Français Deutsch Español Italiano Nederlands Svenska 中文 Русский

• Please ask your dealer regarding assembly of the electronic board and instruction for wall-mounting.

Before installing this set, please read this manual completely.

CLASS 1 LED PRODUCT

WARNING

DO NOT INSTALL THIS OPTION EXCEPT

QUALIFIED SERVICE PERSONNEL.

CAUTION

SAFETY CHECK MUST BE DONE BY

QUALIFIED SERVICE PERSONNEL AFTER

INSTALLING THIS OPTION.

Table of Contents

page

Assembling the Electronic Board . . . . . . . . . . . . . . . . . . . . . . . 3

●Accessories for assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

●Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electronic Board Operations Check. . . . . . . . . . . . . . . . . . . . 11

Repacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Assembling the Optional Stand (UE-608005) . . . . . . . . . . . . 13

●Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

●Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Wall-mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

●Wall-mounting fixture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

●Wall-mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

●Attaching the wall-mounting fixtures. . . . . . . . . . . . . . . . . . . . . . . . . 19

English

Assembling the Electronic Board

■Accessories for assembling

The package includes the parts for setting up the electronic board shown below. Make sure that all of these parts

are included in the package before proceeding.

* These names [Wall-mounting fixture (upper)/Wall-mounting fixture (lower)] are used for installing on the wall.

Part Name Illustration/Quantity Remarks

Board attachment

(upper)

[*Wall-mounting

fixture (upper)]

Board attachment

(lower)

[*Wall-mounting

fixture (lower)]

Cover (upper)

Cover (lower)

Screws and spacers

For screen

For printer

and screen For cover For screen For screen

Screen

Page 6, Step 11

Printer

Page 8, Step 17

Cover (lower)

Page 10, Step 22

Paper holder

Wrench

Power cord

Wall-mounting

template

Use the Wall-mounting

template1 and 2 by

pasting them together.

(Long) (Short)

661 6

Q’ty

Assembling the Electronic Board

■Assembly

1Assemble the optional stand or wall-mounting fixture.

■If you are using a stand, refer to page 13.

■If you are using a wall-mounting fixture, refer to page 17.

2Remove the electronic board from the shipping box.

Remove the joints, then remove the electronic board from the shipping box.

Caution

• When removing the screen unit, grasp the side cover on either side of screen.

Do not grasp the screen film surface, as this may scratch it.

• The shipping box, cushioning material, and other packing material will be necessary if you ever need to

repackage the electronic board, so do not throw them away.

Board attachment (lower)

Board attachment (upper)

Copy paper roll

Power cord

Cover (upper)

Cover (lower)

Markers

Screen unit

Printer unit

Eraser

Paper holder ·

Manuals, CD-ROM

Joint

Screws and spacers

Assembling the Electronic Board

English

3Collapse the carton box.

Remove the tape and the staples on

the unopened side of the carton box,

then collapse the box.

4Remove the protective plastic bags.

Remove the protective plastic bag

from the screen unit and printer unit.

Set those units on the top of collapsed

shipping box and remove the

cushions.

Caution

• Touch the screen film surface gently to avoid

any damage.

5Attach the screen unit to the

optional stand or wall mounting

fixture.

■If you are using the stand, refer to

page 13.

■If you are using the wall mounting

fixture, refer to page 17.

6Hang the screen unit to the board

attachment (upper).

Hold the side covers of the screen unit

and hang two hooks of the screen unit

on the left side of the board

attachment (upper).

Shift the screen unit to the left until it

stops. Confirm the left hook is inserted

into the groove of the board

attachment (upper).

• When hanging the screen unit, set the board

attachment frame at the lowest level.

• Be careful not to catch the screen film on the

board attachment frame.

7Remove the shipping screws.

Remove the lower and upper shipping

screws on the folded screen.

Caution

• Remove the lower shipping screw first.

Carton

To p

Bottom

Remove the tape

and the staples.

Protective

plastic bag

Screen unit

Cushions

Cover (left) Board attachment

(upper)

Cover (right)

Board

attachment

Frame

Assembling the Electronic Board

8Extend the screen unit.

Open the center and right panels of

the screen unit as shown below and

remove the cushion.

Caution

• Touch the screen film surface gently when

opening the screen unit.

9Unlock the hook.

Unlock the hook connected to the

center and right panels. Extend the

screen unit and remove the cushion

behind the screen.

Caution

• Touch the screen film surface gently when

opening the screen unit.

10 Extend the screen unit.

Hang the right hook of the screen unit

on the board attachment (upper).

Caution

• Touch the screen film surface gently when

opening the screen unit.

11 Fix the screen unit.

Fix the left, center and right panels

with the screws and spacers supplied.

To tighten the screws, use the

supplied wrench.

Cushion

Lift the right

panel slightly

and extend it.

Hook

Cushion

Right hook

Spacers

Screws (short)

Screws

(long)

Washer

Assembling the Electronic Board

English

■Adjusting the level of the screen

unit (Step 12–15: only for use of

the optional stand)

At the lowest level of the board attachment frame,

the printer cannot be installed. Raise the level of

the screen unit as follows.

• Please lock the casters when you adjustment the

screen height. Refer to Operating Instructions

page 5.

12 Loosen the height adjustment

handles on the board attachment

frame.

13 Hang the step frame on the center

of the reinforce pipe.

Hold the center of the board attachment

(lower) of the board attachment frame from

the back of the screen unit and lift the board

attachment frame by stepping on the step

frame to lift the board attachment frame

smoothly.

When lifting the board attachment frame, be

sure to hold the handle in the center of the

frame.

14 Hang the screen in the desired slots

of the slide plates and tighten the

handles.

Caution

The screen can be adjusted at 4 levels.

• The lowest level of the board attachment frame

is designed for the installation of the screen, so

the printer cannot be attached at that level. Use

the electronic board at upper 3 levels.

• Make sure to tighten the height adjustment

handles firmly after adjusting the level of the

screen.

• Confirm both of the screws are hung in the same

height slots.

• Store the step frame by hanging it on the board

attachment (upper).

Height

adjustment

handles

Height

adjustment

handles

Board

attachment

(lower)

Reinforce pipe

Step frame

Slot for installing

the screen

(The printer cannot

be attached at this

position.)

Slots for

height

adjustment

Step frame

Assembling the Electronic Board

15 After hanging the screen, fix the

stopper screw (left side only).

This prevents the user from adjusting

the screen height at the lowest level by

mistake.

16 Attach the printer unit.

Hang the hooks of the printer unit on

the square holes of the board

attachment (lower).

Caution

• When attaching the printer unit, make sure the

cable is not caught between the metallic frame

and the printer unit.

17 Tighten the screws for the printer

unit.

Use four screws for the optional stand

and two screws for the wall mounting.

■Optional stand

■Wall-mounting

Stopper screw

[Screw(short)

See page 13.]

Board attachment

(lower)

Printer unit

Assembling the Electronic Board

English

18 Connect the cables (2) to the screen

panel connectors.

19 Remove the folding support screw

on the front side of the screen unit,

then store the folding support on

the back side.

20 Attach the cover (upper).

Hook the cover with the projections on

both sides, then cover the top of the

board attachment (upper).

21 Store the shipping screws for fixing

the screen panels, the screw for the

folding frame and the wrench in the

tool box on the top of the printer

unit.

Folding support screw

Folding support

Board attachment (upper)

Cover (upper)

Tool box

Shipping screws

Wrench

Folding support screw

Assembling the Electronic Board

22 Attach the cover (lower).

(1) Push the cover in the direction of

the arrow until it clicks.

(2) Fix the cover with the wing bolt.

23 Attach the power cord.

Securely fit the supplied power cord

into the AC inlet on the printer unit.

24 Attach the paper holders.

Attach the paper holders to the printer

section in numerical order of the

arrows (1), (2), (3) and (4).

25 Attach the rear cover. (only for use

of the optional stand)

• After peeling off the cover sheets of the

adhesive tapes, attach the rear cover to the

board attachments (upper/lower) while

matching the top edges of them. Then install

the rivets.

• The rear cover and rivets are supplied with

the optional stand.

26 Wipe the screen film surface.

Soak a soft cloth with water, wring

well, and wipe the screen film surface.

Caution

• Do not wipe the screen film surface with paint

thinner, benzene, or cleaners that contain

abrasives. Doing so may cause discoloration.

• Do not wipe the screen film surface with a dry

cloth. Doing so may create static electricity.

27 Check the operations.

Refer to “Electronic Board Operations

Check” on page 11.

AC inlet

Power cord

Paper holder

Install first.

Hole for A

Hole for B

Hole for A

Paper holder

Install second on top of first.

Adhesive

tape

Rivets

Autres manuels pour Panaboard UB-5310

Table des matières

Autres manuels Panasonic Tableau blanc interactif

Panasonic

Panasonic Panaboard UB-8325 Manuel utilisateur

Panasonic

Panasonic Panaboard UB-5315 Manuel utilisateur

Panasonic

Panasonic UB-5365 Manuel utilisateur

Panasonic

Panasonic Panaboard UB-5310 Manuel utilisateur

Panasonic

Panasonic Panaboard KX-BP800U Manuel utilisateur

Panasonic

Panasonic Panaboard UB-7325 Manuel utilisateur

Panasonic

Panasonic UB-5325 Manuel utilisateur

Panasonic

Panasonic Panaboard UB-7325 Manuel utilisateur

Panasonic

Panasonic KX-B730A Manuel utilisateur

Panasonic

Panasonic UB-T781 Manuel utilisateur

Panasonic

Panasonic Panaboard UB-7325 Manuel utilisateur

Panasonic

Panasonic Panaboard UB-5315 Manuel utilisateur

Panasonic

Panasonic Panaboard KX-BP535 Manuel utilisateur

Panasonic

Panasonic ELITE PANABOARD UB-T780 Manuel utilisateur

Panasonic

Panasonic Panaboard KX-BP800 Manuel utilisateur

Panasonic

Panasonic ELITE PANABOARD UB-T780BP Manuel utilisateur

Panasonic

Panasonic UB-5335 Manuel utilisateur

Panasonic

Panasonic UBT780C Manuel utilisateur

Panasonic

Panasonic Panaboard UB-5310 Manuel utilisateur

Panasonic

Panasonic ELITE PANABOARD UB-T780 Manuel

Panasonic

Panasonic Panaboard UB-5815 Manuel utilisateur

Panasonic

Panasonic Panaboard UB-8325 Manuel

Panasonic

Panasonic Panaboard UB-5315 Manuel utilisateur

Panasonic

Panasonic UB-5838C Manuel utilisateur

Manuels Tableau blanc interactif populaires d'autres marques

SMART

SMART KAPP42 Manuel utilisateur

HitachiSoft

HitachiSoft StarBoard FX-TRIO-88W Manuel utilisateur

Buhl

Buhl LyteBoard Manuel utilisateur

SMART Board

SMART Board 680 Manuel utilisateur

SMART

SMART SBX880 Manuel utilisateur

Legamaster

Legamaster e-SCREEN ETX Manuel utilisateur

SMART Board

SMART Board SBM685ix2 Manuel utilisateur

Seneca

Seneca eno Manuel utilisateur

BenQ

BenQ RP840G Manuel utilisateur

SMART

SMART Sympodium IC-150 Manuel utilisateur

Olivetti

Olivetti OLIBOARD Manuel utilisateur

Turning Technologies

Turning Technologies MOBIVIEW Manuel utilisateur

Dukane

Dukane ITP84 Manuel utilisateur

Bretford

Bretford EDUIMS Guide de configuration

Plus

Plus M-11S Manuel utilisateur

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Manuel utilisateur

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Manuel utilisateur

AVer

AVer CP series Manuel utilisateur