Panasonic WV-CU980 Manuel technique

WV-CU980 software update procedure

This manual describes the software update procedures for WV-CU980 (hereafter also referred to as this product).

Use the i-PRO Configuration Tool to update the software.

First, read ‘Installing the i-PRO Configuration Tool’ on page 3 of this manual, and install the Configuration Tool on your

PC. Also, connect this product and the PC to the network.

Note

•In this manual, ‘This product software’ is called ‘software’ or ‘firmware’.

1Insert the power supply plug of the AC adapter

into a power socket while simultaneously

pressing + +

The administrator ID input screen is displayed.

2Enter the administrator ID using the numeric

buttons

The administrator ID that has been input is displayed on

the screen.

3Press

The password input screen is displayed.

4Enter the administrator password using the

numeric buttons

5Press

When a wrong administrator ID or password has been

input, the blinking message ‘Invalid’ will be displayed for a

few seconds, and then the display returns to the

administrator ID input screen. Input again the correct

administrator ID and password. If the admin ID and

password are entered correctly, the software reception

waiting screen will be displayed.

6Use the i-PRO Configuration Tool to update the

software of this product

Run ‘Software Update by i-PRO Configuration Tool’ on

page 4 of this manual.

The software receiving screen is displayed.

Note

•Software update may take up to 1 minute while the

software receiving screen remains displayed.

•Do not turn off the power of this product or perform

other operations while updating the software.

•If an error occurs in communication with the i-PRO

Configuration Tool, the software receiving screen

may not be displayed and the software update

failure (download error) screen (described later) may

be displayed.

•Contact your dealer for further information about

the firmware update.

When the software update is completed, the software

update completion screen is displayed.

Software update complete (normal) screen is displayed.

The next time you turn on this product, the updated

software will start.

WV-CU980 side operation

Operation procedure

If any of the following errors occur, the software update

failure (download error) screen will be displayed.

•Error in communication between this product and the

i-PRO Configuration Tool

→ Check the communication environment between this

product and the i-PRO Configuration Tool, and then

update the software again

•Software sent from the i-PRO Configuration Tool to this

product is not genuine software

→ Check if the software specified by the i-PRO

Configuration Tool is genuine software for this

product, and then update the software again

The next time you turn on this product, the pre-update

software will start.

If any of the following errors occur, the software

update failure (write error) screen will be displayed

•Error while writing the software received from the i-PRO

setting tool to the memory of this product

→Please update the software again

The next time you turn on the power of this product, the

software shipped with this product will start.

Note

•The launched software version will be displayed on

the display for a few seconds when the power is

turned on. For details, see ‘Switching ON the

Power’ (☞page 15) in the Operating Instructions for

this product.

7Turn off the power

Remove the power supply plug from the power supply

socket.

i-PRO Configuration Tool

Installation of i-PRO Configuration Tool

With a web browser, access the following Panasonic Support Website and go to the download page.

　　https://security.panasonic.com/training_support/design_tools/iCT/

Follow the procedure described on the download page to download and install the i-PRO Configuration Tool (V1.3 or

higher) on your PC.

Note

•

The downloaded data includes the instruction manual of the i-PRO Configuration Tool (i-PRO Configuration Tool.pdf).

Please read here for the required PC specifications and the basic operation method of the i-PRO Configuration Tool.

•From here, we will explain using the screen of the i-PRO Configuration Tool (some parts may differ from the actual screen).

Launch i-PRO Configuration Tool

Start the i-PRO Configuration Tool.

The ‘Register new user’ screen is displayed.

Click the [Log in] button.

Note

•The ‘Register new user’ screen opens only at the first startup after installation, and the ‘Log in’ screen opens

from the second time onward.

Firmware update with i-PRO Configuration Tool

When you log in, the ‘Select Menu’ screen is displayed.

Select the IP address of the network adapter used to communicate with the WV-CU980.

After selecting [Basic mode], check ‘Update Firmware’ in [Maintenance].

Click the [Next] button.

If the following ‘Detection Result’ screen is displayed, click the [x] button at the top right of the screen to close the

screen.

If the following ‘Error’ screen is displayed, click the [OK] button.

Note

•Where WV-CU980 does not detect the connection with the device, the above error screen may be displayed

even if the PC and WV-CU980 are connected correctly.

Click the [Option] on the ‘Title bar’.

The [Option] screen is displayed.

Select the [Communication].

Click ‘Enable the WV-CU980 firmware update operation.’ in ‘Update Firmware’.

Click the [OK] button.

Select the ‘Update Firmware’.

Click the [Next] button from ‘CU980 Firmware Update’.

The ‘CU980 Firmware Update’ screen is displayed.

Enter the IP address of WV-CU980.

Select the WV-CU980 firmware (*.img) downloaded from the Panasonic Support website below.

　　https://security.panasonic.com/training_support/documentation_database/

Note

•Search for ‘WV-CU980’ in the [Model Number] field on the above site, and download the firmware from [Firmware]

on the product page.

Click the [Execute] button.

IMPORTANT

•Before clicking the [Execute] button, check that the software reception waiting screen (page 1 5in this manual)

is displayed on the WV-CU980 display.

Note

•For details on how to check the IP address of WV-CU980, refer to ‘Network Settings’ (☞page 27) in the WV-CU980

Operating Instructions.

L1020-0 PGQQ1435ZA

After the updating screen is displayed for up to 1 minute, the update completion screen is displayed.

Click the [OK] button.

If the update fails, the following error screen will be displayed.

Click the [OK] button to turn off the error screen.

Check if the PC and WV-CU980 are connected correctly, and if the IP address etc. are set correctly, and then update

the firmware again.

Autres manuels Panasonic Panneau de contrôle

Panasonic

Panasonic AWRP501 - HYBRID CONTROL PANEL Manuel utilisateur

Panasonic

Panasonic WX-CC411 Manuel utilisateur

Panasonic

Panasonic AK-HRP1005G Manuel utilisateur

Panasonic

Panasonic AWRP655N - MULTI FUNCTION CONTROLLER Manuel utilisateur

Panasonic

Panasonic AWRP505 - MULTI HYBRID CTL PAN Manuel utilisateur

Panasonic

Panasonic AWRP301 - PAN/TILT CONTROL PAN Manuel utilisateur

Panasonic

Panasonic AK-HRP1005G Manuel utilisateur

Panasonic

Panasonic AK-HRP1000G Manuel utilisateur

Panasonic

Panasonic AK-HRP1000G Manuel utilisateur

Panasonic

Panasonic AG-RCP30P Manuel utilisateur

Panasonic

Panasonic AK-HRP1010G Manuel utilisateur

Panasonic

Panasonic AV-HS60C3G Manuel utilisateur

Panasonic

Panasonic AK-HRP200GJ Manuel utilisateur

Panasonic

Panasonic AK-HRP1005G Manuel utilisateur

Panasonic

Panasonic AWRP555N - MULTI FUNCTION CONTROLLER Manuel utilisateur

Panasonic

Panasonic AY-RP500 Manuel utilisateur

Panasonic

Panasonic AY-RP500 Manuel utilisateur

Panasonic

Panasonic AWRP305 - MULTI PAN TILT CTL P Manuel utilisateur

Panasonic

Panasonic AWRP501 - HYBRID CONTROL PANEL Manuel utilisateur

Panasonic

Panasonic AWRP301 - PAN/TILT CONTROL PAN Manuel utilisateur

Panasonic

Panasonic AK-HRP250G Manuel utilisateur

Panasonic

Panasonic AV-HS60C4P Manuel utilisateur

Panasonic

Panasonic AV-SF500 Manuel utilisateur

Panasonic

Panasonic AK-HRP1000G Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques