Panasonic ZU-1870MA6T2 Manuel utilisateur

Spec.No.: MES-DG60B038A

SPECIFICATIONS

FOR

MANUAL INSERTION

MAGNETIC CARD READER

Z U – 1 8 7 0 M A 6 T 2

MATSUSHITA ELECTRIC INDUSTRIAL CO.,LTD.

MATSUSHITA INDUSTRIAL EQUIPMENT CO.,LTD.

CONTENTS

1. INTRODUCTION---------------------------------------------------------------- P-1

2. COMPOSITION------------------------------------------------------------------ P-1

3. SPECIFICATION----------------------------------------------------------------- P-1

4. TERMINAL NO. OF CONNECTOR--------------------------------------- P-3

5. INTERFACE REQUIREMENTS--------------------------------------------- P-3

6. NOTES FOR BETTER OPERATION------------------------------------- P-5

7. APPEARANCE--------------------------------------------------------------------P-6

8. CONNECTOR DIMENSION---------------------------------------------------P-7

9. MAGNETIC CARD SPECIFICATION--------------------------------------P-7

10. LIFE OF PARTS----------------------------------------------------------------P-8

11. MAINTENANCE METHOD---------------------------------------------------P-8

12. CAUTIONS ON THE USE---------------------------------------------------P-8

1. INTRODUCTION

This specification applies to the Panasonic magnetic card reader,

featuring small size, light weight and high performance.

2. COMPOSITION

The magnetic card reader is composed of the mechanical portion,

double circuits for reading.

1) Mechanical portion

The mechanical portion is mainly composed of the following parts.

1. Body (Color:Transparence)

2. Card entrance slot (Color: Black)

3. Magnetic head

4. Rubber seal

2) Circuit portion

1. Read amplifier circuit for 2 tracks

3. SPECIFICATION

3.1 CARD STANDARD

Refer to Magnetic Card Specification (9).

3.2 FUNCTION

(1) Read/Write : Read only

(2) Read timing : Ejection

(3) Compatibility : Cards and installation

(4) Installation of the transport : Horizontal direction

3.3 BASIC PERFORMANCE

(1) Performance

(2) Card operation speed : 10 cm/s to 100 cm/s

(3) Magnetic head Channel : 2

Channel width : 1.4 mm

(4) Insulation resistance : More than 10 MΩat DC 250 V

(Measured between P.C.B. ground terminal and frame)

(5) UL File No. : E140407

(6) Waterproof level : IPX4

3.4 ENVIRONMENT REQUIREMENTS

(1) Temperature range : -20 oC to 60 oC

(Operation)

(2) Temperature range : -30 oC to 70 oC

(Conservation)

(3) Humidity range : 10 % RH to 90 % RH

(Operation) (No condensation allowed)

(4) Humidity range : 10 % RH to 90 % RH

(Conservation) (No condensation allowed)

(5) Vibration : Vibration sweep 10 Hz to 50 Hz,

sweep 0.5 oct/min

X,Y,Z directions : 10 m/s

(6) Shock durability : 294 m/s2 (30 G)

ZU-1870MA6T2

ISO 7810,7811

Card standard

IS01 IS02

Track used Track 1st Track 2nd

Recording method FM FM

Recording

density 210 BPI 75 BPI

Recording

Capacity

79 characters

(7-bit code)

40 characters

(5-bit code)

3.5 PHYSICAL CHARACTERISTICS

(1) Dimension : (W) 90 mm x (D) 119.5 mm x (H) 46 mm

(2) Mass : Approx. 100 g

(3) Power supply : DC 5 V ± 0.5 V / Ripple(Less than 25 mA)

(4) Ripple : Within 50 mV

p-p

(5) Operating place : Indoor

3.6 ERROR RATE

(at indoor conditions by continuous running)

(1) Error : Less than 0.5 %

* Condition ··················In a clean office room.

In damp or dusty atmosphere, the life may be 1/3 to 1/5 of

the above figure.

4. TERMINAL NO. OF CONNECTOR

4.1 OUTPUT SIGNAL

Connector: 641216-7

5. INTERFACE REQUIREMENTS

5.1 OUTPUT VOLTAGE

Min(V) Max(V) Conditions

H level "0"

4.0 V

cc I

OH= -1.0 mA

L level "1"

- 0.4 I

OL= 4.0 mA

Connector

Pin No.

Signal

name

Connector

Pin No.

Signal

name

DC 5 V 5 /RCL2

/RDT1 6 /CLD

/RCL1 7 GND

/RDT2 - -

5.2 OUTPUT SIGNALS

The following paragraphs describe the requirements

and interface signals between the user terminal and

the Magnetic Card Reader shown in Figure 1.

The general timing sequence for entering data from

the Magnetic Card Reader to the user terminal is shown

in Figure 2.

/CLD

Magnetic /RCL1,2 User's

Card Reader /RDT1,2 Terminal

GND

DC 5V

Figure 1

(1) /CLD (CARD LOAD)

The /CLD line will be High when a Magnetic Card is inserted

in the end of Magnetic Card Reader.

The /CLD line will be Low at all other times.

(2) / RCL1,2 (READ CLOCK)

This is used to sample the data line by it's falling edges.

The time relationship of the clock with respect to the other

signals is shown in Figure 2.

User's Terminal starts to carry out sampling of the read data

by the falling edge of the signal.

In case of performing sampling other than the falling edge

sampling method

(such as detecting “L” of /RCL by means of polling)to read

/RDT, check /RCL width if it is appropriate.

(3) /RDT1,2 (READ DATA)

At the moment /RCL change from High to Low ;

/RDT is "1" when the /RDT line is Low, and

/RDT is "0" when the /RDT line is High.

5.3 TIMING CHART

Detail Chart

When the jitter of the magnetic head output is 0 % , the following

equation is satisfied.

T=T1=T2=T3, t1=t2

2.54 cm/inch 1

Note : T (s) = x

Recording density (BPI) Card speed (cm/s)

6. NOTES FOR BETTER OPERATION

(1) The card should be inserted in the specified direction.

(2) The card which conformed ISO standard should be used.

(3) The cards should not be dirty, scratched or deformed.

7. APPEARANCE

8. CONNECTOR DIMENSION

POST(641216-7 AMP)

9. MAGNETIC CARD SPECIFICATION

9.1 CARD SPECIFICATION

(1) Thickness : 0.76 mm (tolerance ± 0.08 mm)

(2) Transformation : 2 mm max.

(3) Impermeability rate : More than 2.0

(Measured by light permeance desitometer)

9.2 MAGNETIC CHARACTERISTICS

(1) Coercive force (Hc) : 2.4 x 10

4A/m (300 Öe ± 12%)

(2) Residual flux (¢r) : 1.25 x 10-8 Weber/cm

(1.25 ± 0.15 maxwell/cm)

(3) Squareness ratio (¢r/¢m) : More than 0.70

10. LIFE OF PARTS

Magnetic head : 500,000 passes

*Condition ·············· In a clean office room.

In damp or dusty atmosphere, the life may be

1/3 to 1/5 of the above figure.

11. MAINTENANCE METHOD

When replacing parts, exchange the card reader unit.

12. CAUTIONS ON THE USE

Please be noted that we do not guarantee proper performance of the

card reader if it is used other than the indicated specification range.

12.1 At the installation

(1) Do not drop or bump anything against a card reader.

Otherwise, failure may be the result.

(2) Do not touch the P.C.B. with bear hands.

(3) Be sure to install on a flat surface so as to prevent any force to be

applied to the card reader at the installation.

(4) Installation of a card guide plate at the both (front and back) sides of

the card running part may reinforce stability.

(5) The card reader should avoid installation of the following environment.

· Watery, humid or dusty place.

· Near machines which generate magnetic field or inducted noise.

(printer,LED display, CRT etc.)

· Place which gets direct sunlight.

Table des matières

Autres manuels Panasonic Lecteur de cartes

Panasonic

Panasonic AJ-PCD2GPJ Manuel utilisateur

Panasonic

Panasonic AJ-MPD1G Manuel utilisateur

Panasonic

Panasonic AJ-PCD10E Manuel utilisateur

Panasonic

Panasonic AJ-PCD30PJ Manuel utilisateur

Panasonic

Panasonic AJ-PCD10P Manuel utilisateur

Panasonic

Panasonic FZ-VSC552 Series Manuel utilisateur

Panasonic

Panasonic CF-VCRU11U Manuel utilisateur

Panasonic

Panasonic au-xpd1 Manuel utilisateur

Panasonic

Panasonic FZ-VSC401 Series Manuel utilisateur

Panasonic

Panasonic LP-ABR10 Series Manuel de la liste des pièces

Panasonic

Panasonic FZ-VSC551 Series Manuel utilisateur

Panasonic

Panasonic BN-SDCMAB Manuel utilisateur

Panasonic

Panasonic FZ-VSDR55 Series Manuel utilisateur

Panasonic

Panasonic AJHPM110E - MEMORY CARD PORTABLE... Manuel utilisateur

Panasonic

Panasonic au-xpd1 Manuel utilisateur

Panasonic

Panasonic FZ-VSC402 Series Manuel utilisateur

Panasonic

Panasonic FZ-VNF401 Series Manuel utilisateur

Panasonic

Panasonic AJ-PCD20EJ Manuel utilisateur

Panasonic

Panasonic AJ-PCD35 Manuel utilisateur

Panasonic

Panasonic JT-R210CR-50 Manuel utilisateur

Panasonic

Panasonic FZ-VGT551 Series Manuel utilisateur

Panasonic

Panasonic AJ-PCD2GPJ Manuel utilisateur

Panasonic

Panasonic ZU-9PS Series Manuel utilisateur

Panasonic

Panasonic AJ-PCD35 Manuel utilisateur

Manuels Lecteur de cartes populaires d'autres marques

Lindy

Lindy 43185 Manuel utilisateur

Lindy

Lindy 43185 Manuel utilisateur

ViziT

ViziT RD-4F Manuel utilisateur

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuel utilisateur

AVID ID

AVID ID AVID1043 Manuel utilisateur

Conrad

Conrad PCMCIA Manuel utilisateur

Rosslare

Rosslare DR-6255 Manuel utilisateur

Lindy

Lindy 51541 Manuel utilisateur

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuel utilisateur

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuel utilisateur

ACS

ACS ACR122L Manuel utilisateur

Secukey

Secukey S2-MF Manuel utilisateur

Elecom

Elecom MR-SMC07 series Manuel utilisateur

Alien

Alien ALR-9800 Manuel utilisateur

ACS

ACS ACR310 Manuel utilisateur

Datamars

Datamars R-IN1300 MID Manuel utilisateur

Alarm Lock

Alarm Lock AL-PRE2 Manuel utilisateur

xpr

xpr B100PROX-AH Guide de l'utilisateur