Panasonic VDR-D210P Manuel utilisateur

rights reserved. Unauthorized copying and

distribution is a violation of law.

VDR-D210P

VDR-D220P

VDR-D230P

VDR-D210PC

VDR-D220PC

VDR-D230PC

Vol. 1

Colours

(S)...................Silver Type

Digital Video Camcorder

ORDER NO. MKE0701450CE

B17

1 Safety Precautions 3

1.1. General Guidelines 3

2 Warning 4

2.1. Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices 4

2.2. How to Recycle the Lithium Battery 4

2.3. How to Replace the Lithium Battery 5

3 Service Navigation 6

3.1. Introduction 6

3.2. About Lead Free Solder (PbF) 6

4 Specifications 7

5 Service Mode 8

5.1. Error Display 8

5.2. Service Menu 8

6 Service Fixture & Tools 10

6.1. Service Fixture and Tools 10

6.2. Service Position 11

6.3. Removal/Installation of F.P.C. From Non ZIF (Zero

Insertion Force) Connector 13

6.4. Method for Ejecting the DVD Tray Manually 14

6.5. EEPROM Data 14

6.6. Special Note 15

6.7. Model No. Identification Mark 15

7 Disassembly and Assembly Instructions 16

7.1. Cabinet Section 16

8 Measurements and Adjustments 35

8.1. Electrical Adjustment 35

9 Maintenance 37

9.1. Cleaning Lens, Viewfinder and LCD Panel 37

9.2. Cleaning disc and optical pickup 37

10 Troubleshooting 39

11 Voltage Chart of Connectors on Main P.C.B. 48

12 Block Diagrams 49

13 Schematic Diagrams 51

13.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT

NOTES 51

13.2. FRONT SCHEMATIC DIAGRAM 52

13.3. BOTTOM SCHEMATIC DIAGRAM 53

13.4. LCD BACKLIGHT SCHEMATIC DIAGRAM 54

13.5. SIDE R / EVF FPC / EVF BACKLIGHT / LED LIGHT

SCHEMATIC DIAGRAMS 55

13.6. CCD / REAR CASE / LCD SW SCHEMATIC DIAGRAMS

13.7. SIDE L/OPERATION / DISK COVER LOCK SCHEMATIC

DIAGRAMS 57

13.8. INTERCONNECTION SCHEMATIC DIAGRAM 58

14 Printed Circuit Board 59

14.1. FRONT P.C.B. 59

14.2. BOTTOM P.C.B. 60

14.3. LCD BACKLIGHT P.C.B. 61

14.4. SIDE R P.C.B. 62

15 Exploded View 63

15.1. MAIN PARTS SECTION 63

15.2. FRONT HOOD AND FRONT P.C.B. SECTION 64

15.3. SIDE R OPERATION AND LCD SECTION 65

15.4. CCD AND LENS SECTION 66

15.5. GRIP COVER AND EVF SECTION 67

15.6. PACKING PARTS AND ACCESSORIES SECTION 68

16 Replacement Parts Lists 69

16.1. REPLACEMENT NOTES 69

16.2. MECHANICAL REPLACEMENT PARTS LIST 70

16.3. ELECTRICAL REPLACEMENT PARTS LIST 71

CONTENTS

Page Page

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

1 Safety Precautions

1.1. General Guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment

which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essential

that these critical parts should be replaced with

manufacturer’s specified parts to prevent shock, fire, or

other hazards. Do not modify the original design without

permission of manufacturer.

2.An Isolation Transformer should always be used during the

servicing of AC Adaptor whose chassis is not isolated from

the AC power line. Use a transformer of adequate power

rating as this protects the technician from accidents

resulting in personal injury from electrical shocks. It will also

protect AC Adaptor from being damaged by accidental

shorting that may occur during servicing.

3.When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been

overheated or damaged by the short circuit.

4.After servicing, see to it that all the protective devices such

as insulation barriers, insulation papers shields are properly

installed.

5.After servicing, make the following leakage current checks

to prevent the customer from being exposed to shock

hazards.

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

2 Warning

2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage

caused by electro static discharge (ESD).

1.Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2.After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4.Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable

conductive material).

7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8.Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)

sufficient to damage an ES device).

2.2. How to Recycle the Lithium Battery

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

2.3. How to Replace the Lithium Battery

The lithium battery (CGR-F/202AW) is not supplied as a service part and must be replaced as part of the Bottom P.C.B. (Refer to

“Disassembly and Assembly Instructions.")

NOTE:

This Lithium battery is a critical component. (Type No.: CGR-F/202AW Manufactured by Panasonic.) (Not supplied)

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in equipment designed specifically for its use.

Replacement batteries must be of the same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

3 Service Navigation

3.1. Introduction

This service manual contains technical information which will allow service personnel´s to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service

manual.

Note 1:

AC Adaptor used on these movie camera is PV-DAC14D. However, DE-974FB is supplied as a replacement part for PV-

DAC14D. This AC Adaptor is supplied only as a unit.

3.2. About Lead Free Solder (PbF)

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

4 Specifications

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

5 Service Mode

5.1. Error Display

"PUSH THE RESET SWITCH" is displayed automatically on the EVF or the LCD Monitor when an undesirable condition has

occurred.

Fig. 1

Note:

When "PUSH THE RESET SWITCH" is displayed repeatedly, service is required. Check the Error Code which is listed in the

Service Menu.

5.2. Service Menu

When abnormal detection contents are confirmed, do the following operation. Automatic diagnosis code will bedisplayed. (Service

Menu)

To enter the Service Menu

Push the [DELETE], [JOYSTICK CONTROL LEFT] and [RECORDING START/STOP] simultaneously for 3 seconds (with no

SD Card inserted).

Note:

If a Disc or SD Card is inserted, the above operation will not work.

Fig. 2-1

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

Note:

Only perform items 1, 3, and 4 in the Service Menu.

To select the Item

1.Set to Service Menu.

2.Press [JOYSTICK CONTROL UP/DOWN] to select item [1], [3], or [4].

3.Press [JOYSTICK CONTROL RIGHT] to display [YES/NO] screen.

4.Press [JOYSTICK CONTROL UP/DOWN] to select [YES].

5.Press [JOYSTICK CONTROL CENTER] to end.

Fig. 2-2

To exit the Service Menu

Unplug the AC Cord.

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

6 Service Fixture & Tools

6.1. Service Fixture and Tools

VDR-D210P / VDR-D220P / VDR-D230P / VDR-D210PC / VDR-D220PC / VDR-D230PC

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic caméscope

Panasonic

Panasonic Digital Palmcorder PV-DV101 Manuel utilisateur

Panasonic

Panasonic Palmcorder MultiCam PV-DV702 Manuel utilisateur

Panasonic

Panasonic AG-HVX200E Manuel utilisateur

Panasonic

Panasonic HDC-SD100PC Manuel utilisateur

Panasonic

Panasonic HDC-SDT750PP Manuel utilisateur

Panasonic

Panasonic SDC615 - AJ Camcorder - 520 KP Manuel utilisateur

Panasonic

Panasonic Palmcorder MultiCam PV-DV702 Manuel utilisateur

Panasonic

Panasonic DIGITAL Palmcorder PV-GS59 Manuel utilisateur

Panasonic

Panasonic PV-L552 Manuel utilisateur

Panasonic

Panasonic NV-MX300EN/A Manuel utilisateur

Panasonic

Panasonic SDR-SW20P Manuel utilisateur

Panasonic

Panasonic PV-GS33PP Manuel utilisateur

Panasonic

Panasonic AVCCAM AG-AF101E Manuel utilisateur

Panasonic

Panasonic PV-GS80P Manuel utilisateur

Panasonic

Panasonic NV-RX10A Manuel utilisateur

Panasonic

Panasonic NV-DS88EN Manuel utilisateur

Panasonic

Panasonic NVRX9 Manuel utilisateur

Panasonic

Panasonic NV RZ 10 Manuel utilisateur

Panasonic

Panasonic Palmcorder PV-DV53 Manuel utilisateur

Panasonic

Panasonic HC-DC3 Manuel utilisateur

Panasonic

Panasonic GP-KH232 Manuel utilisateur

Panasonic

Panasonic NV-DS77EN Manuel utilisateur

Panasonic

Panasonic AJ-HPX3100G Manuel utilisateur

Panasonic

Panasonic NV-S1A Manuel utilisateur

Manuels caméscope populaires d'autres marques

Toshiba

Toshiba CAMILEO Z100 Manuel utilisateur

Canon

Canon RC 260 Manuel utilisateur

Sony

Sony Handycam DCR-DVD7E Manuel utilisateur

Brinno

Brinno TimeLapse TLC200 Manuel utilisateur

JVC

JVC GR-SXM68AC Guide de démarrage rapide

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Manuel utilisateur

MYDLINK

MYDLINK DCS-6100LH Manuel utilisateur

Sony

Sony video Hi8 Handycam CCD-TR555 Manuel utilisateur

SECURECOM

SECURECOM V-5014B Manuel utilisateur

Sharper Image

Sharper Image U-VIDEO Manuel utilisateur

JVC

JVC AA-V15EG Manuel utilisateur

Canon

Canon LEGRIA HV40 Manuel utilisateur

Sony

Sony Handycam DCR-VX2000 Manuel utilisateur

RCA

RCA CC616 Manuel utilisateur

ATIK Cameras

ATIK Cameras Horizon Manuel utilisateur

Sony

Sony Handycam HDR-CX580V Manuel utilisateur

Sharp

Sharp ViewcamZ VL-Z8H Manuel utilisateur

Philips

Philips M620/21 Manuel utilisateur