Panasonic DMP-BD60 - Blu-Ray Disc Player Manuel utilisateur

Panasonic DMP-BD60/BD80

Region switching guide

With the mod. chip fitted the player will automatically play DVD's from all regions (1-6),

but for Blu-ray disc playback the region must be manually selected.

Blu-ray Region switching is done using the player's original remote control while the

player is in standby mode, by pressing the following buttons:

'1' : Select Blu-ray region 'A'

'2' : Select Blu-ray region 'B'

'3' : Select Blu-ray region 'C'

When the player is powered up out of standby mode the new Blu-ray region will be

active. The selected Blu-ray region will remain active until the player is disconnected

from mains power or a new region is selected while the player is in standby mode.

Note that the player must fully enter standby mode to allow the mod. chip to change the

Blu-ray region, therefore the player's "Quick Start" mode (which keeps the player fully

powered up even in standby mode) must be disabled when changing Blu-ray regions.

Blu-ray region switching is possible with any remote channel setting, 1, 2 or 3.

Panasonic DMP-BD60/BD80

Mod. chip fitting guide

Warning: Modifying your player will invalidate any existing warranty. The mod. chip is

difficult to fit, requiring soldering of small surface mount components and therefore

fitting should only be carried out by those with the appropriate experience. A low power

(15-25W) soldering iron with very small tip is essential. If you don't have the required

tools and experience do not attempt to fit the mod. chip as it's very likely that you will

damage your player.

Please read this guide fully before starting to fit the mod. chip.

Before opening the player ensure that all cables are completely disconnected from it.

Double check that the mains cable is disconnected.

To open the player remove the 7 fixing screws, 2 from left side, 2 from right side and 3

from the rear. The top cover can now be lifted off.

The main board is on the right side and the image below shows the areas where the mod.

chip will be connected to it.

6 pins on the mod. chip are used in total, #1, #2, #3, #4 and #8 connect to the main board

and #5 to the rear of the front panel.

Mod. chip pin #1 should be connected to the 2nd bottom of the 6 long solder pads, as

shown.

Mod. chip pins #2, #3, #4 and #8 should be connected to the small 8 pin chip as shown.

For access to the connection point for mod. chip pin #5 the front panel of the player has to

be removed. To remove the front panel, look for the 7 plastic clips holding it in place, 1

left, 1 right, 2 top and 3 bottom. Carefully unclip them from one side, then the other and

the front panel should pull free.

With the front panel removed you can now see the area where mod. chip pin #5 will be

connected.

Connect pin #5 to the point on the front panel PCB shown below.

Bring the wire for mod. chip pin #5 in under the metal plate at the front of the player,

ensuring that it doesn't block the connector shown at the left side.

When re-fitting the front panel check that all 7 plastic clips are fully in place, otherwise

the electrical connectors may not contact correctly.

Pins #1 and #5 should be connected with wires, however for the pins that connect to the 8

pin chip on the main board (#2, #3, #4 and #8) it's possible to either connect them with

wires or to "piggy-back" the mod. chip on top of the 8 pin chip on the board. If you

connect all the pins with wires then the mod. chip must be wrapped in insulation tape and

secured in a safe position, so the "piggy-back" option is quicker and only requires 2 wires

for pins #1 and #5.

To "piggy-back" the mod. chip, bend pins #2, #3, #4 and #8 inwards against the body of

the mod. chip and then #3, #4 and #8 as shown below. Trim pins #1 and #5 and

trim/remove the unused pins #6 and #7.

Bend the pins into position and then hold it against the chip on the board to make sure

they are lined up correctly. Once all the pins are lined up solder pin #8 first, then you can

carefully position the mod. chip by rotating it slightly and solder pins #2, #3 and #4.

It should then look similar to the image below.

And the full install should look like this, with the wires for pins #1 and #5 in place.

If you're not confident with the "piggy-back" fitting method just use wires to connect all 6

pins of the mod. chip.

Autres manuels pour DMP-BD60 - Blu-Ray Disc Player

1

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Panasonic Lecteur Blu-ray

Panasonic

Panasonic DMP-B200 Manuel utilisateur

Panasonic

Panasonic DMP-BDT384 Manuel utilisateur

Panasonic

Panasonic DP-UB424 Manuel utilisateur

Panasonic

Panasonic DMR-PWT550 Manuel utilisateur

Panasonic

Panasonic DMP-BDT260 Manuel utilisateur

Panasonic

Panasonic DMR-BWT740 Manuel utilisateur

Panasonic

Panasonic DMP-BDT460 Manuel utilisateur

Panasonic

Panasonic DMPBD79 Manuel utilisateur

Panasonic

Panasonic DMP-BD75P Manuel utilisateur

Panasonic

Panasonic DMP-BDT385 Caractéristiques techniques

Panasonic

Panasonic DMP-BD903 Instructions d'installation et d'entretien

Panasonic

Panasonic DP-UB420 Manuel utilisateur

Panasonic

Panasonic DMP-BDT300GA Manuel utilisateur

Panasonic

Panasonic DMR-HWT250 Manuel utilisateur

Panasonic

Panasonic DMP-BD87 Manuel utilisateur

Panasonic

Panasonic DMP-BDT111 Manuel utilisateur

Panasonic

Panasonic DMP-BD75GA Manuel utilisateur

Panasonic

Panasonic DMPBDT100 - 3D BLU-RAY DISC PLAYER Manuel utilisateur

Panasonic

Panasonic DMP-BD793 Manuel utilisateur

Panasonic

Panasonic DMP-BD30K Manuel utilisateur

Panasonic

Panasonic DMP-BDT110 Manuel utilisateur

Panasonic

Panasonic DMP-BDT230P; DMP-BDT230PC Manuel utilisateur

Panasonic

Panasonic Diga DMR-BWT735 Manuel utilisateur

Panasonic

Panasonic DMP-DSB100 Manuel utilisateur

Manuels Lecteur Blu-ray populaires d'autres marques

Samsung

Samsung BD-F5900 Manuel utilisateur

Philips

Philips BDP3380K Manuel utilisateur

Samsung

Samsung BD-P4600 Manuel utilisateur

Sharp

Sharp BD-HP17U - AQUOS 1080p Blu-ray DiscTM Player Manuel utilisateur

Pioneer

Pioneer BDP-140 Manuel d'installation et d'exploitation

Samsung

Samsung BD-D8200A Manuel utilisateur

LG

LG HLX50W Manuel utilisateur

Sony

Sony BDP-S300 - Blu-Ray Disc Player Manuel utilisateur

Marantz

Marantz UD9004 Manuel utilisateur

LG

LG BD611 Manuel utilisateur

LG

LG BD611 Manuel utilisateur

Marantz

Marantz BD7004 Guide de démarrage rapide

Kogan

Kogan KABRP3DWFIA Manuel utilisateur

Toshiba

Toshiba BDX2700 Manuel utilisateur

Samsung

Samsung BD-E5400 Manuel utilisateur

Samsung

Samsung BD-F5100 Manuel utilisateur

Philips

Philips BDP7100 Manuel utilisateur

LG

LG UBK80.DUSALLK Manuel utilisateur