Palsonic HDSTB200 Manuel utilisateur
HDSTB200
High Definition Digital Receiver
User Manual
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Safety Information
CAUTION
CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK,
DO NOT OPEN.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
The lightning flash with arrowhead symbol within an equilateral triangle,
is intended to alert the user to the presence of uninsulated dangerous
voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and servicing instructions
In the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO WATER OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK. ENSURE 240V AC POWER
PLUG IN FULLY INSERTED INTO THE POWER SOCKET.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY
THE MANUFACTURER WILL VOID THE USER'S WARRANTY.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO ENSURE RELIABLE OPERATION AND PREVENT THE HS-STB
FROM OVER HEATING, YOU MUST REMOVE THE PROTECTIVE
PLASTIC FILM FROM THE HS-STB COVER.
WARNING:
Important Safeguards
These important safeguard messages will help ensure your enjoyment and proper
use of the HD-STB and accessories. Please read them carefully before you begin
to operate your HD-STB product.
1. Read and Retain this User's Guide
This User's Guide should be read before the HD-STB is operated and retained for
future reference
2. Use Correct Power
This HD-STB should be operated only from the type of power source indicated on
the rear panel.
3. HD-STB Installation
Do not place HD-STB on an unstable trolley stand, tripod, bracket, or table as it
may fall, causing serious injury to a child or adult and damage the HD STB.
4. Provide Antenna Ground
If an outside antenna or cable system is connected to the HD-STB, be sure the
antenna or cable system is grounded to provide some protection against
voltage surges and built-up static charges. An outside antenna system should not
be located in the vicinity or overhead power lines, or other power circuits, where
it can fall onto such power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching or approaching such
power lines or circuits as contact with them might be fatal. Installing an outdoor
antenna can be hazardous and should be left to a professional antenna installer.
5. Provide Proper Ventilation
Opening slots in the STB cabinet are provided for ventilation to ensure reliable
STB operation and to protect it from overheating. HD-STB should not be located
in an enclosed / built-in installation such as a bookcase unless proper ventilation
is provided.
For sufficient ventilation, there must be at least 10cm free air space above,
behind, top and on each side of the HD-STB.
6. Keep Away from Heat
Do not expose the HD-STB to direct sunlight. This product should be situated
away from heat sources such as radiators, heat registers, stoves and other
electronic products (including amplifiers) that produce heat.
Important Safeguard
7. Keep Away from Moisture
Do not use HD-STB near water or in wet areas such as near a bathtub, wash bowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool and the
like.
Caution: Maintain electrical safety, Power line operated equipment or
accessories connected to this unit should bear the CE listing mark or C-Tick
certification mark on the accessory itself and should not be modified to defeat
the safety features. This will help avoid any potential hazard from electrical
shock or fire.
8. Do Not Open
Do not attempt to service this HD-STB, as opening or removing STB cover will
expose you to dangerous voltages. To prevent of the risk of fire or electric shock,
do not open the cabinet. There are no user serviceable parts inside the HD-STB.
Refer servicing to qualified service personnel only.
9. Unplug before Cleaning
When cleaning the HD-STB, turn the HD-STB power off and unplug it from the
wall AC outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning only.
10. Object and Liquid Entry
Never push objects of any kind through HD-STB openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric
shock.
Never spill liquid of any kind on the HD-STB. In case of liquid spillage,
please contact your qualified service centre.
11. For Additional Protection
For added protection during a lightning storm, or when left unattended for long
periods of time, unplug the HD-STB from the AC wall outlet and disconnect the
antenna and A/V cable system. This will prevent damage to the HD-STB from
Lightning and power line surges.
1
CONTENTS
3
3
4
5
8
8
10
Front Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Rear Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Remote Control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Installing remote control batteries
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Remote Control Universal Code Setting
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Accessories
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11
Antenna Connection
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
HD-STB, TV and VCR antenna connection
HD-STB and TV antenna connection
Video Connection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
HDMI (High Definition Multimedia Interface) connection
Connecting to a HDTV with HD YPbPr
Connecting to a Conventional TV with S-Video
Connecting to a Conventional TV with Composite Video
Audio Connection
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Stereo Audio Connection
Digital Audio Connection
Display Mode Change - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
STB Connection to 576p/720p/1080i High Definition Display
STB Connection to Standard Definition Display
Step 1. Unpacking and accessories.
Step 2. Remove Protective Plastic Film.
Step 3. Connect ANT Cable.
Step 4. Connecting the Video.
Step 5. Connecting the Audio.
Step 6. Connecting the Power.
Step 7. Display Mode Setup.
Step 8. Install Remote Control battery and Universal
Code Setting.
Step 9. Check up the On Screen Display.
Step 10. Automatic Channel Search and Channel Change.
19
User Preference - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Preferred Audio Type (I-II)
SD Output Aspect Ratio
i-Plate Banner Duration
Front Panel LED Dimmer
Power Restore
4. Using Menu System - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3. Getting Started - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2. Connecting Your HD-STB - - - - - - - - - - - - - - - - - - - - - - - - - - -
1. Overview of the Equipment
- - - - - - - - - - - - - - - - - - - - - - - - -
1)
1)
2)
3)
4)
11
12
15
16
17
19
2
Content
2 1
24
26
5. Remote Control Buttons 28
6. Trouble Shooting Guide - - - - - - - - - - - - - - - - - - - - - - - - - -
7. Reception Trouble Shooting Guide - - - - - - - - - - - - - - - - - -
8. Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
9. Remote Control Universal Code List - - - - - - - - - - - - - - - - -
31
32
34
36
Channel Setup - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Channel Favourites
Automatic Channel Scan
Manual Channel Scan
Test Reception
Access & Timer Setup - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Program Blocking Level
Wake-up Channel
Wake-up Timer
Power-off Timer
System Setup
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Time Zone
Auto Power Off
Factory Reset
System Information
TV Remote Control Code List
2)
3)
4)
1) Using INFO button - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2) Using EPG button
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3) Using LIST & FAV button - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4) Using ZOOM button - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
5) Using FREEZE button
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
28
29
30
30
30
3
Overview of the equipment
This section summarises HD-STB buttons, controls, and terminals.
Front Panel
POWER
Press to turn the HD-STB on or off.
Power Indicator
Displays STB operation status. In power off mode, STB will display a RED light. In
power on mode the RED light will flash to acknowledge a remote control key press.
Remote Sensor
Infrared red remote control sensor. To ensure reliable remote control operation do not
place any objects in front of the sensor.
Video Display Mode Indicators
Two green LEDs indicate the current HD video display mode setting LED combination
is as follows:
1.
2.
3.
4.
5. UP / DOWN
Channel up or down movement. These two buttons also change the HD video display
mode as detailed on page 16.
720p
576p
1080i
12345
4
Overview of the equipment
Rear Panel
LOOP OUT Terminal
Use this terminal to feed RF signal to your TV or VCR for analogue TV reception.
ANT IN Terminal
Attach an external Antenna to this terminal.
Optical Digital Audio (SPDIF) Output terminal
Use this terminal with A/V device equipped with Optical Digital input for Dolby* Digital
5.1-channel sound.
Coaxial Digital Audio (SPDIF) Output terminal
Use this terminal with A/V device equipped with Coaxial Digital input for Dolby* Digital
5.1-channel sound.
S-Video Output terminal
Use this terminal with your TV S-Video input.
TV Composite Video Output terminal (CVBS)
Use this terminal with your TV Video input.
AUDIO L/R (Analog Stereo Audio) Output terminal
This terminal can be used with your TV analog audio input. Refer to Audio Connection.
Pages.
HD YPbPr (HD Component Video) Output terminal.
Use this terminal with your TV HD Component Video input. (HDTV only)
HDMI Output terminal
Use this terminal with your TV HDMI Video input.
RS-232C
Use this terminal for software upgrade purpose only.
External IR Sensor Terminal
Use this terminal for External IR Sensor connection.
Power Cord
Plug this Cord to the specified AC Power socket.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Manufactured under license from Dolby Laboratories. Dolby and the double-D Symbol are
trademarks of Dolby Laboratories.
10
12
12
3 4 5
67
8911
5
Overview of the equipment
Remote Control
POWER
Turn your HD-STB on or off.
TV
Change your Remote Controller to TV mode.
VCR
Change your Remote Controller to VCR mode.
0~9 (Number Button)
Direct change the desired channel.
To change the channel, simply press desired channel number.
The button operation should be less than 2 seconds between button pressing.
1.
2.
3.
4.
14 15
16
17
18
10 11
12 13
1
23
4
5
6
7
8
9
33
32
34
35
36
31
30
29
28 27
26
22
23
24 25
19
20 21
6
Overview of the equipment
PgUp (STB Mode)
In the menu system, move up item list by page.
CH+ / CH-
Change the TV/HDTV's analog channel / Change the STB's digital channel.
PREV (Previous Channel - STB mode)
Go to the previous watched channel.
Up / Down
In the menu system, move up or down the cursor.
Exit
In the menu system, exit menu from any menu level.
LIST (STB Mode)
Set & display ALL DTV channel list as the default channel list.
FAV (STB Mode)
Set & Display FAV DTV channel list as the default favourite channel list.
I-II (STB mode)
Switch between MPEG and Dolby Digital audio.
Subtitle (STB Mode)
Enable/ disable program subtitles.
RED (F1)
RED button. Also worked with function 1 button.
GREEN (F2)
GREEN button. Also worked with function 2 button.
REWIND
In the VCR or DVD mode, it works with REWIND button.
PLAY
In the VCR or DVD mode, it works with PLAY button.
STOP
In the VCR or DVD mode, it works with STOP button.
AV (TV's External Video Input Selection)
Select the TV External Video Input.
DVD
Change your Remote Controller to DVD mode.
STB
Change your Remote Controller to STB mode.
PgDn (STB Mode)
In the menu system, move down item list by page.
VOL+ / VOL-
Change the TV/HDTV's volume level up or down.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Table des matières
Autres manuels Palsonic Récepteur TV
