Paladin Tools 1573 Manuel utilisateur

Paladin Tools®

Features and Benefits

• A complete test system for data and

telephone installations

• Applies distinct, selectable tone patterns

• Applies tone to balanced and unbalanced

circuits using dual (Tip & Ring) or single

(Tip) modes

• Tests line and load continuity

• Tests polarity of standard phone systems

• Red and black alligator clip-to-RJ11 cable

included

• Tone probe has adjustable volume control

• Cable mapper tests RJ45 and RJ11 local

patch cables & installed cables for

continuity including cross-over telephone

connections. Tests data and telephone

connection schemes

• Cable-check identifies opens, shorts, cross

connections, and good connections

• Tests UTP, STP, and flat satin cable types

with RJ45 connections.

• Two RJ45 shielded patch cords included

• Two 9-volt batteries included

• Auto-off battery save function

• Durable nylon carrying case with belt loop

included

• Two RJ11 patch cords included

Technical

Weight 18 oz. (complete kit)

Tone Generator

Dimensions 6.75” L x 1.35” W x 1.08” D

Output Voltage 8Vdc (open), 5Vdc (600Ωload)

Battery 9Vdc NEDA 1604, JIS 006P, IEC 6LR61

Battery life 120 hrs (NEDA 1604)

Auto-Off 1 hr (tone mode)

Output Frequency 8 tones: 523, 587, 659, 698, 784,

880, 988, 1046 HZ

Tone Sequences 4 patterns: single oscillating, dual

slow, dual fast & multi-tone

Connection RJ11 6-pin modular plug

Tone Probe

Dimensions 5.92” L x 1.35” W x 1.08” D

Battery 9Vdc NEDA 1604, JIS 006P, IEC 6LR61

Battery life 120 hrs (NEDA 1604)

Tone Pick-up Inductive type, non-conducting

Cable-Check

Cable Types EIA/TIA-568A & B Cat-3 through

Cat-6, flat satin telephone, 4-pair

UTP/STP, 25-pair UTP/STP, 24/4

and 22/4 telephone line

Connection Types RJ45 shielded (STP) or unshielded (UTP)

Output Signal 9Vdc nominal at 10mA max.

Voltage Protection Connector pins protect up to 56Vdc

with 400Ωseries resistance applied

for 2 minutes

Max. Cable Length 1650 feet (500 m)

Tone Tracing Note: the tone signal only emits from the top RJ11 socket.

Tone is NOT present on the side RJ45 socket

DO NOT USE ON LIVE CIRCUITS

1. For testing directly into RJ11 wall jacks, use an RJ11 patch cord wired 1-to-1

connection (provided). Connect the RJ11 patch cord into the top of the tone

generator in the RJ11 socket. (Proceed to step 4).

2. For testing telephone boxes, discreet wire connections, or open contact

connections install the alligator clip cable provided into the top of the tone

generator in the RJ11 socket. (Proceed to step 4).

3. To test RJ45 systems, use the RJ11-to-RJ11 patch cord provided to connect into

the top of the tone generator in the RJ11 socket. An RJ11 plug is compatible to

insert into most RJ45 sockets. The tone will be applied to the RJ45 two center

pins #4 and #5 respectively. In the event the RJ11 plugs on the patch cord is not

compatible with the RJ45 socket, use an RJ11-to-RJ45 adapter patch cable (not

provided) ensuring the two center pins for the RJ11 plug are mated to the

two center pins of the RJ45 plug, or use an 8-way RJ45 Modular Adapter (also

known as a “banjo”) such as the Paladin Tools model 1902. (Modular Adapter

is not provided).

4. Set the “tlk, cont, line/tone” slide switch located on the side of the tone

generator to the “line/tone” position.

5. Press the “TONE” button to turn on the tone generator. Press the “TONE”

button to change operating modes. Indications are as follows:

Rev & Norm lights Tone operation “ON”

Dual light Tone applied to red (Tip) and black (Ring) alligator clips or to pins 3

(Ring) and 4 (Tip) or RJ11 plug

Single light Tone applied to red alligator clip only (RJ11 socket pin 4 - Tip) with

black (RJ11 socket pin 3 - Ring) open for grounded connections

Single

Dual

Rev

Norm

Tone Operation

Dual Mode

Single

Dual

Rev

Norm

Tone Operation

Single Mode

Example: Light Indications

Operating Instructions

Tone operation

Dual Mode

Tone operation

Single Mode

Tone operation

Dual Mode

Reverse

Normal Reverse

Normal

Dual Dual

Single Single

LAN & Telecom Cable Testing Kit

1573

Paladin Tools®

Testing Cables for Pin-out Wiring Configuration (Cable Mapping):

DO NOT USE ON LIVE CIRCUITS

1. For testing local patch cables, connect the cable between the RJ45 sockets

located on sides of the tone generator and tone probe.

2. For testing installed cables, use a patch cable to connect the tone generator

into the jack at one end, and a patch cable to connect the tone probe

into the jack at the opposite end of the cable.

3. Set “tlk, cont, line/tone” switch on side of tone generator to the “cont” position.

4. Set the tone generator “slow, fast, off” switch on the mapper transmitter to

either the “slow” or “fast” position to scan through pins 1-8 and shield.

5. Read the lights for pins 1 through 8, and shield on the Tone Generator/

Cable-Check Transmitter and the Tone Probe/Cable-Check Receiver units to deter

mine connections through the cable. If one light on each end is shown, there is a

good connection between the respective pins. If a light appears on the Cable-Check

Transmitter and no lights appear on the Cable-Check Receiver, there is an open

contact between the respective connectors. If multiple lights appear on the trans

mitter or receiver at any one time, a short exists between respective contacts.

For the RJ11 6-wire systems, pins 1 and 8 are not shown. Pins 2 through 7 will

light up only whereas, light 2 equals pin 1 of the RJ11 cable and light 7

equals pin 6 of the RJll Cable.

Sample Test Results:

Remote Light Sequence Cable Fault

1 2 3 4 5 6 7 8 S None, cable wired correctly

2 1 3 4 5 6 7 8 S Conductors 1 & 2 reversed

1 2 & 3 2 & 3 4 5 6 7 8 S Conductors 2 & 3 are shorted

1 2 3 - 5 6 7 8 S Conductor 4 is open

1 2 4 3 6 5 7 8 S Pair 3/6 is transposed with pair 4/5

1 2 3 7 5 6 4 8 S Conductors 4 & 7 are switched

1 2 3 4 5 6 7 8 - Shield is open

X 2 3 4 5 6 7 X RJ11 6-pin is wired directly

Shield Shield

T.P.

Shield

T.P.T.G.

Shield

T.P.T.G.

Shield

T.P.T.G.

T.G.

Cable Mapping

Good 1-to-1

Cable Mapping

Cross 7-to-4

Cable Mapping

Short 1-to-2, 2-to-1

Cable Mapping

Open Pin 3

Shield Shield

T.P.

T.G.

Cable Mapping

Open Pin 5

LAN & Telecom Cable Testing Kit

1573

Transmitter Receiver Transmitter Transmitter Transmitter TransmitterReceiver Receiver Receiver Receiver

NOTES:

RED

BLACK

connectool Inc. - USA • Support: 800.272.8665 • Int’l 001.804.550.1121 • web: paladin-tools.com • 06/05connectool Inc. - USA • Support: 800.272.8665 • Int’l 001.804.550.1121 • web: paladin-tools.com • 06/05

Paladin Tools®

6. For best results, use “Dual” for balanced line toning, and “Single” for

unbalanced line toning. Press and hold the “TONE” button to change tone

patterns.

7. Use the tone probe to detect tone signals along the cable length. Press and

hold the “TRACE” button to activate the tone probe. The “Power” light will

turn on when button is depressed. Use the “volume” adjustment located on

the side of the tone probe to set volume to desired level.

8. For quiet operation, insert standard 3.5 mm head phones into the headset

socket located on the side of the probe.

9. Set “tlk, cont, line/tone” switch on side of tone generator to the “cont”

position when storing. Leaving the switch in the “line/tone” position will

not cause any battery drainage unless the metal tips of the red and black

alligator clips touch.

Testing phone circuit polarity:

WARNING! LIVE CIRCUIT TESTING - USE CAUTION

ENSURE THE TONE GENERATOR IS TURNED OFF

1. For testing directly into RJ11 wall jacks, use the RJ11 patch cord wired 1-to-1

connection.Connect the RJ11 patch cord into the top of the tone generator in the

RJ11 socket. (Proceed to Step 4).

2. For testing telephone boxes, discrete wire connections or open contact

connections, install the alligator clip cable provided into the top of the tone

generator in the RJ11 socket. (Proceed to Step 4).

3. To test RJ45 systems, use the RJ11-to-RJ11 patch cord provided to connect into

the top of the tone generator in the RJ11 socket. An RJ11 plug is compatible to

insert into most RJ45 sockets. The tone will be applied to the RJ45 two center

pins #4 and #5 respectively. In the event the RJ11 plugs on the patch cord is not

compatible with the RJ45 socket, use an RJ11-to-RJ45 adapter patch cable (not

provided) ensuring the two center pins for the RJ11 plug are mated to the two

center pins of the RJ45 plug, or use an 8-way RJ45 Modular Adapter (also known

as a banjo) such as the Paladin Tools model 1902 (Modular Adapter is not provided).

4. Set the “tlk, cont, line/tone” slide switch located on the side of the tone

generator to the “line/tone” position.

5. If the polarity for the TIP and RING is correct, the “Normal” light will turn on. If

the polarity for the TIP and RING is reversed, the “Reverse” light will turn on.

6. Perform steps 4 and 5 to check line status. If the line is not in use, the “Normal”

or “Reverse” lights will be brightly lighted. If the line is in use, the “Normal” or

“Reverse” lights will be dim. If the line is ringing, the “Normal” or “Reverse” lights

will flash.

Single

Dual

Rev

Norm

Polarity Testing

Normal Polarity

Sin

Dual

Rev

Norm

Polarity Testing

Reverse Polarity

Examples: Test Results

and Indications

LAN & Telecom Cable Testing Kit

1573

Polarity Testing

Normal Polarity

Polarity Testing

Reverse Polarity

Reverse Reverse

Normal Normal

Dual Dual

Single Single

Paladin Tools®

Testing Continuity of Lines and Loads:

DO NOT USE ON LIVE CIRCUITS

ENSURE THE TONE GENERATOR IS TURNED OFF

1. Install the alligator clip cable into the top of the tone generator.

2. Set the “tlk, cont, line/tone” slide switch located on the side of the tone

generator to the “cont” position.

3. Connect the alligator clip test leads to the ends of the cable or across the

load to be tested.

4. If the DC resistance (continuity) of the cable or load is 12000Ω(12KΩ) or

less, the “Reverse” light will turn on indicating a path of continuity.

5. Set the “tlk, cont, line/tone” switch on side of tone generator to the “cont”

position when storing. Leaving the switch in the “line/tone” position will

not cause any battery drainage unless the metal tips of the red and black

alligator clips touch.

Talk Power/Battery Power for Butt Set Communications

DO NOT USE ON LIVE CIRCUITS

ENSURE THE TONE GENERATOR IS TURNED OFF

1. Install the alligator clip cable into the top of the tone generator.

2. Connect the alligator clips so the tone generator is in series with the butt

set at one end of the dead pair.

3. Connect a second butt across the dead pair at the opposite end of the line.

4. Set the “tlk, cont, line/tone” slide switch located on the side of the tone

generator to the “tlk” position.

5. Take both butt sets off “hook” open communications.

6. Set “tlk, cont, line/tone” switch on side of tone generator to the “cont”

position when storing. Leaving the switch in the “line/tone” position will

not cause any battery drainage unless the metal tips of the red and black

alligator clips touch.

Single

Dual

Rev

Norm

Continuity Testing

Good Continuity

Single

Dual

Rev

Norm

Continuity Testing

No Continuity/High Res.

Examples: Test Results

and Indications

LAN & Telecom Cable Testing Kit

1573

Continuity Testing

Good Continuity Continuity Testing

No Continuity/High Res.

Reverse Reverse

Normal Normal

Dual Dual

Single Single

NOTES: NOTES:

connectool Inc. - USA • Support: 800.272.8665 • Int’l 001.804.550.1121 • web: paladin-tools.com • 06/05 connectool Inc. - USA • Support: 800.272.8665 • Int’l 001.804.550.1121 • web: paladin-tools.com • 06/05

Table des matières

Autres manuels Paladin Tools Équipement de test