Pacific hydrostar 95338 Manuel utilisateur

PRESSURE WASHER

1800 PSI

Model

95338

ASSEMBLY AND OPERATION INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND

ALL WARNINGS AND INSTRUCTIONS BEFORE USE.

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 95338 PAGE 2

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

Contents

Unpacking ................................................................................2

Specications ..........................................................................3

Safety........................................................................................3

General Safety Rules........................................................................ 3

 SpecicSafetyRules ....................................................................... 6

Grounding.......................................................................................... 8

Assembly.................................................................................10

Controls And Setup................................................................12

Operation.................................................................................15

Operating Tips ........................................................................16

Inspection, Maintenance, And Cleaning...............................18

Parts Lists And Diagrams......................................................19

Parts List A / Assembly Diagram A................................................. 19

Parts List B....................................................................................... 20

Assembly Diagram B....................................................................... 21

Parts List C / Assembly Diagram C................................................ 22

Warranty ..................................................................................23

Troubleshooting .....................................................................24

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts Lists and

Diagrams near the end of this manual are included. If any parts are missing or broken,

please call Harbor Freight Tools at the number shown on the cover of this manual as soon

as possible.

SKU 95338 PAGE 3

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

SPECIFICATIONS

Electrical Requirements 120 V / 60 Hz / 13 A

3-Prong GFCI Power Plug

35 Ft. Long Power Cord

Water Pressure 1,800 PSI

Flow Rate 2.1 Gallons Per Minute

Water Supply Required 3-4 GPM minimum

Hose Length 19 Ft.

Additional Feature Safety Lock Off Trigger

Weight 36.5 lb.

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, oper-

ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

IMPORTANT SAFETY INSTRUCTIONS!

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electricshock,re,and/orseriousinjury.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit. Cluttered and dark work areas invite ac-

cidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool. Distrac-

tions can cause you to lose control.

ELECTRICAL SAFETY

Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

30929053092905

SKU 95338 PAGE 4

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

modify the plug in any way. Do not use any adapter plugs. Check with a quali-

ed electrician if you are in doubt as to whether the outlet is properly grounded. If

the tools should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and re-

frigerators. There is an increased risk of electric shock if your body is grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

Do not abuse the Power Cord. Never use the Power Cord to carry the tools or pull

the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges,

or moving parts. Replace damaged Power Cords immediately. Damaged Power

Cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked “W-

A” or “W”. These extension cords are rated for outdoor use, and reduce the risk

of electric shock.

PERSONAL SAFETY

Stay alert. Watch what you are doing, and use common sense when operating a

power tool. Do not use a power tool while tired or under the inuence of drugs,

alcohol, or medication. A moment of inattention while operating power tools may

result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

Avoid accidental starting. Be sure the Power Switch is off before plugging in. Car-

rying power tools with your nger on the Power Switch, or plugging in power tools

with the Power Switch on, invites accidents.

Remove adjusting keys or wrenches before turning the power tool on. A wrench or

a key that is left attached to a rotating part of the power tool may result in personal

injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the power tool in unexpected situations.

Use safety equipment. Always wear eye protection. Nonskid safety shoes, hard

hat, or hearing protection must be used for appropriate conditions. Always wear

ANSI approved safety impact goggles and thick rubber boots during use and main-

tenance.

SKU 95338 PAGE 5

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

TOOL USE AND CARE

Use clamps (not included) or other practical ways to secure and support a smaller

workpiece to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

Do not force the tool. Use the correct tool for your application. The correct tool will

do the job better and safer at the rate for which it is designed.

Do not use the power tool if the Power Switch does not turn it on or off. Any tool that

cannot be controlled with the Power Switch is dangerous and must be replaced.

Disconnect the Power Cord Plug from the power source before making any adjust-

ments, changing accessories, or storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

Maintain tools with care. Keep tools clean. Properly maintained tools are easier

to control. Do not use a damaged tool. Tag damaged tools “Do not use” until re-

paired.

Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used

on another tool.

SERVICE

Tool service must be performed only by qualied repair personnel. Service or main-

tenance performed by unqualied personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instructions

in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of un-

authorized parts or failure to follow maintenance instructions may create a risk of

electric shock or injury.

SKU 95338 PAGE 6

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

SPECIFIC SAFETY RULES

Maintain a safe working environment. Keep the work area well lit. Make sure

there is adequate surrounding workspace. Always keep the work area free of ob-

structions, grease, oil, trash, and other debris. Do not use the Pressure Washer in

areas near ﬂammable chemicals, dusts, and vapors.

Maintain labels and nameplates on the Pressure Washer. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a replace-

ment.

WARNING!Riskofinjectionorsevereinjury.KeepclearofNozzle.Do

not direct discharge stream at people or animals. Keep the work area clear of

all people and animals.

Usetherightproductfortherightjob.There are certain applications for which

this product was designed. Do not use small equipment, tools, or attachments to

do the work of larger industrial equipment, tools, or attachments. Do not use this

product for a purpose for which it was not intended.

This product must continuously run with cold water only. Never use hot wa-

ter. Dry running will cause serious damage to the seals. Make sure the water

supply used for the Pressure Washer is not dirty, sandy, and does not contain any

corrosive chemical products.

To avoid electrical shock, never start and run the Pressure Washer in the rain.

Never allow water to leak inside the Body of the Pressure Washer. Do not direct dis-

charge stream at the Pressure Washer itself or at other live electrical equipment.

Do not allow the GFCI Plug (35a) to become wet. Always place the GFCI Plug

inadrylocationandasfarawayaspossiblefromtheobjectbeingsprayed.

Keep all electrical connections dry and off the ground.

WhenusingthePressureWasher,alwaysmaintainarmgripontheWash

Gun (18a) with both hands. Squeezing the Trigger of the Wash Gun causes a

kickback force.

Do not pull or carry the Power Washer by its Power Cord (35a), or pull the Cord

around sharp corners or edges. Do not unplug the Power Washer by pulling on

the Cord. Keep the Cord away from heated surfaces.

Do not handle the GFCI Plug (35a) with wet hands.

Avoid unintentional starting. Make sure you are prepared to begin work before

turning on the Pressure Washer.

The work area should have adequate drainage to reduce the possibility of a

fall due to slippery surfaces.

This Pressure Washer is intended for outdoor residential use only.

10.

11.

12.

13.

SKU 95338 PAGE 7

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

Some chemicals or detergents may be harmful if inhaled or ingested. Use

an ANSI approved respirator or mask whenever there is a chance that vapors may

be inhaled.

Keep the High Pressure Hose connected to the Pressure Washer and Spray

Gunwhilethesystemispressurized.Disconnecting the Pressure Hose while

the unit is pressurized is dangerous, and may cause injury.

Prior to starting the Pressure Washer in cold weather, check all of the parts

of the unit to make sure ice has not formed. Do not store the unit anywhere that

the temperature will fall below 32° F (0° C). (See “Inspection, Maintenance, and

Cleaning” section for proper storage procedures.)

Donotfeedalready-pressurizedwater(Suchasthatfromanotherpressure

washer) into this washer.

When dispensing detergent, apply the detergent to the cleaning area at low

pressure only. Then, spray the detergent off the cleaning area by using the ad-

justable Nozzle. NOTICE: Detergent dispensing only works when the spray wand

is in the low-pressure position.

Thehighpressurewaterowcandamagetheworksurfaceifnotusedprop-

erly. Always test the spray in an open area ﬁrst.

Never move the Pressure Washer by pulling on the High Pressure Hose. Use

the Handle provided on the top of the unit.

Never leave the Pressure Washer unattended when it is plugged into an elec-

trical outlet. Turn off the Pressure Washer, and unplug it from its electrical outlet

before leaving.

If water is leaking out of the Pressure Washer immediately shut off the unit.

Unplug the Pressure Washer, and discharge all pressure before tightening ﬁttings

or having repair work done by a qualiﬁed technician.

People with pacemakers should consult their physician(s) before use. Elec-

tromagnetic elds in close proximity to heart pacemaker could cause pacemaker

interference or pacemaker failure.

WARNING: The brass components of this product contain lead, a chemical known

to the State of California to cause birth defects (or other reproductive harm). (Cali-

fornia Health & Safety code § 25249.5, et seq.)

WARNING! The warnings and precautions discussed in this manual cannot

cover all possible conditions and situations that may occur. It must be understood

by the operator that common sense and caution are factors which cannot be built

into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

REV 07j

SKU 95338 PAGE 8

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If

the tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of electric

shock. (See Figure A.)

The grounding prong in the plug is connected through the green wire inside the

cord to the grounding system in the tool. The green wire in the cord must be the

only wire connected to the tool’s grounding system and must never be attached to

an electrically “live” terminal. (See Figure A.)

Your tool must be plugged into an appropriate outlet, properly installed and grounded

in accordance with all codes and ordinances. The plug and outlet should look like

that in the following illustration. (See Figure A.)

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric shock.

Checkwithaqualiedelectricianifyouareindoubtastowhethertheoutletis

properly grounded. Do not modify the power cord plug provided with

the tool. Never remove the grounding prong from the plug. Do not use the

tool if the power cord or plug is damaged. If damaged, have it repaired by

aservicefacilitybeforeuse.Iftheplugwillnotttheoutlet,haveaproper

outletinstalledbyaqualiedelectrician.

FIGURE A

3-PRONG PLUG

ELECTRICAL OUTLET

SKU 95338 PAGE 9

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

EXTENSION CORDS

Grounded tools require a three wire extension cord.

As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a seri-

ous drop in voltage, resulting in loss of power and possible tool damage.

(See Table A.)

The smaller the gauge number of the wire, the greater the capacity of the cord. For

example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

WARNING! Do not use 16 or 18 AWG extension cords on this product.

When using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required. (See Table A.)

If you are using one extension cord for more than one tool, add the nameplate am-

peres and use the sum to determine the required minimum cord size.

(See Table A.)

If you are using an extension cord outdoors, make sure it is marked with the sufﬁx

“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualiﬁed electri-

cian before using it. Protect your extension cords from sharp objects, excessive

heat, and damp or wet areas.

Table A

RECOMMENDED MINIMUM WIRE GAUGE FOR POWER CORDS* (120 V)

NAMEPLATE AMPERES

(At Full Load) POWER CORD LENGTH

Feet 50

Feet OVER 50 FEET

12.1 - 16.0 14 12 Extension Cords must

NOT be used.

16.1 - 20.0 12 10

* Based on limiting the line voltage drop to ﬁve volts at 150% of the rated amperes.

Symbology

Table B

Canadian Standards Association

Intertek, Electrical Testing

Laboratories Semko

V~ Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute

(RPM)

SKU 95338 PAGE 10

For technical questions, please call 1-800-444-3353;

Troubleshooting section at end of manual.

ASSEMBLY

NOTE: For additional information regarding the parts discussed in the following pages,

refer to the Assembly Diagrams near the end of this manual.

Check the Inlet Strainer for any blockage, including packaging debris. The Pres-

sure Washer may be shipped with a plastic plug in the Inlet.

HANDLE

(28A)

DETERGENT

PORT

(Hidden Behind

Handle)

DETERGENT

TUBE (32A)

SCREW

(25A)

FIGURE D

REAR

VIEW

SCREW

(25A)

Position the rear of the Handle (28a) above the rear of the Pressure Washer body.

Insert the Valve located at the bottom of the Handle into the Suction Tube located

at the top of the Pressure Washer body. Make sure that the Suction tube does not

bend or get pinched during assembly. Lower the Handle fully onto the Pressure

Washer Body. Then secure the Handle to the Pressure Washer body, using the

Screws (25a) provided. (See Figure D.)

Table des matières

Langues :

Autres manuels Pacific hydrostar Nettoyeur haute pression

Pacific hydrostar

Pacific hydrostar 95672 Manuel d'installation

Pacific hydrostar

Pacific hydrostar 98439 Guide de l'utilisateur

Pacific hydrostar

Pacific hydrostar 69488 Manuel utilisateur

Pacific hydrostar

Pacific hydrostar 69488 Manuel utilisateur

Pacific hydrostar

Pacific hydrostar 97553 Guide de l'utilisateur

Pacific hydrostar

Pacific hydrostar 95618 Manuel d'installation

Pacific hydrostar

Pacific hydrostar 65078 Manuel utilisateur

Pacific hydrostar

Pacific hydrostar 94201 Manuel d'installation

Pacific hydrostar

Pacific hydrostar 99741 Manuel d'installation

Pacific hydrostar

Pacific hydrostar 1650 PSI Manuel d'instructions d'origine

Pacific hydrostar

Pacific hydrostar 98444 Guide de l'utilisateur

Pacific hydrostar

Pacific hydrostar 95156 Manuel utilisateur

Pacific hydrostar

Pacific hydrostar 95619 Manuel utilisateur

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar 212cc Gasoline Powered Clear Water... Instructions de montage

Pacific hydrostar

Pacific hydrostar 68333 Manuel utilisateur

Pacific hydrostar

Pacific hydrostar PACIFIC HYDROSTRAR 97005 Manuel d'installation

Pacific hydrostar

Pacific hydrostar 97552 Guide de l'utilisateur

Manuels Nettoyeur haute pression populaires d'autres marques

Shark

Shark RG-232637 Manuel utilisateur

Shakti Technology

Shakti Technology S3 Manuel utilisateur

Kärcher

Kärcher K 4 Pure Manuel utilisateur

Porter-Cable

Porter-Cable D25806-025-2 Manuel utilisateur

REM POWER

REM POWER HDEm 662 Manuel utilisateur

Landa

Landa HS-3000 Manuel utilisateur

Craftsman

Craftsman 580.752270 Manuel utilisateur

HIKOKI

HIKOKI AW 100 Manuel utilisateur

Delco

Delco DC 1302 Manuel utilisateur

Kärcher

Kärcher K 3 Full Control Manuel utilisateur

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manuel utilisateur

ARKSEN

ARKSEN 014-HG-14141-HR Manuel utilisateur

Black & Decker

Black & Decker PW1700SPX Manuel utilisateur

Kärcher

Kärcher 595 - SPARE Mode d’emploi

Kranzle

Kranzle B 10 200 Manuel utilisateur

Stihl

Stihl RE 90 Manuel utilisateur

Husky

Husky HU80911 Manuel utilisateur

PowR-Quip

PowR-Quip PQ-2600 Manuel utilisateur