Pacific energy Z35 Manuel utilisateur

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

INSTALLATION MANUAL

This appliance is suitable for installation in a

bedroom or bed sitting room.

INSTALLATION

INSTRUCTIONS

Visit www. paciﬁcenergy.net for the most recent version of this manual

MODEL: z35

SERIES: A

ZERO CLEARANCE

DIRECT VENTED GAS

FIREPLACE HEATER

WARNING: If the information in these instruc-

tions is not followed exactly a ﬁre or explosion

may result causing property damage, personal

injury or death.

FOR YOUR SAFETY

Installation and service must be per-

formed by a qualiﬁed installer, service

agency or the gas supplier

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical Switch.

• Do not use any phone in your building.

• Immediately call your gas supplier

from a neighbour’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier

call the ﬁre department.

Do not store or use gasoline or other

ﬂammable vapours and liquids in the

vicinity of this or any other appliance.

This appliance may be installed in an after-

market permanently located, manufactured

home (USA only) or mobile home, where not

prohibited by local codes.

This appliance is only for use with the type of

gas indicated on the rating plate. This appli-

ance is not convertible for use with other

gases unless a certiﬁed kit is used.

z35260619-56 100001042-50

Table of Contents

WARNING:

This product

can expose you to chemicals

including ceramic bers,

which are known to the State

of California to cause cancer, and carbon

monoxide, which is known to the State of

California to cause birth defects or other

reproductive harm.

For more information go to

www.P65Warnings.ca.gov.

This warning is applicable to all

Paciﬁc Energy Fireplace Products

100001042 z35

260619-56

Important Note for the Commonwealth

of Massachusetts .................................................... 3

Caution ....................................................................4

Safety ......................................................................5

Fireplace Dimensions ............................................. 6

Locating the Fireplace .............................................7

Framing and Finishing ............................................ 8

Framing in the z35 .................................................. 9

Framing in the z35 and Optional

Cool Wall Venting Kit .............................................. 9

Lower Opening Trim Piece ....................................11

Clearances to Combustibles .................................12

Standard Conguration .......................................12

Cool Wall Kit .......................................................12

Conguration.......................................................12

Venting Chart ........................................................ 16

Vent Terminal Minimum Clearances ......................17

Venting Conguration ........................................... 18

Vertical Termination .............................................. 19

Vertical Termination using a Duravent Terminal.. 19

Vertical Termination using an ICC Terminal ........ 19

Horizontal Termination .......................................... 20

Horizontal Termination

using a Duravent Terminal.................................. 20

Horizontal Termination using an ICC Terminal ... 20

Electrical Connection ............................................21

Wall Switch Installation ..........................................22

Home Automation ................................................ 23

Control Overview ...................................................24

Gas Valve for Conguration ...................................25

Gas valve and control module.............................25

Gas Connection .................................................... 26

Gas Supply ............................................................27

Gas Pressure Check ..............................................27

Gas pressure requirements .................................27

Gas Pressure Testing Procedure .......................... 29

Gas Leak Detection .............................................. 30

Lighting Instructions ..............................................31

Panel Installation ...................................................32

Glass Bafe Installation .........................................34

Log Set Installation ................................................35

Glass Media Installation ........................................41

Door Installation/Removal .....................................42

Front Surround Installation/Removal .................... 43

Venturi Adjustment ................................................44

Damper Adjustment ..............................................45

Control Panel Removal / Installation .................... 46

Maintenance ..........................................................47

Glass Door: .........................................................47

Annual Inspection: .............................................47

Periodically: ........................................................47

Pairing the Control Module and Fireplace ............ 48

Step 1: Procedure for linking / pairing wall

switch to replace .............................................. 48

Step 2: Procedure for linking / pairing the wall

switch to remote handset................................... 49

Halogen Lamp Replacement ................................ 50

Module & Gas Valve Details ..................................51

Wiring Diagram ......................................................52

Replacement Parts ............................................... 53

Rating Label ..........................................................55

Important Note for the Commonwealth of Massachusetts

From Massachusetts Rules and Regulations 248 CMR 5.08:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential

purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet

above nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised.

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the

installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor

level where the gas equipment is to be installed, in addition, the installing plumber or gas tter shall observe that a battery operated or hard-wired

carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal

vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the

installation of hard-wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard-wired carbon monoxide

detector with alarm and battery back-up may be installed on the next adjacent oor level.

b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of thirty

(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide

detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall

comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet

above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall

read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,

upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.089(2)

(a) 1 through 4.

(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.

1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the

Board; and

2. Product Approved side wall horizontal vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure

used in whole or in part for residential purposes.

(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall

horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided

by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved

side wall horizontally vented gas fueled equipment does not provide the parts for venting the fuel gases, but identies “special venting systems”, the

following requirements shall be satised by the manufacturer.

1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed

installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts

lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

260619-56 100001042

z35

Caution

This ﬁreplace is equipped with a micro mesh safety screen for your protection and

must be installed with the unit. Removal of the safety screen will cause the ﬁreplace

to become a burn and ﬁre hazard.

FOR YOUR SAFETY - Do not install or operate your Pacic Energy replace without rst reading

and understanding this manual. Any installation or operational deviation from the following

instructions voids the Pacic Energy Warranty and may prove hazardous.

This appliance and its individual shut off valve must be disconnected from gas supply piping system

during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

This appliance must be isolated from the gas supply piping system by closing its individual manual

shut off valve during any pressure testing of the gas supply piping system at test pressures equal to

or less than 1/2 psi (3.5 kPa).

Do not use the replace if any part has been under water. Immediately call a qualied service

technician to inspect the replace and to replace any part of the control system and any gas control

which has been under water.

100001042 z35

260619-56

Safety

• Due to high temperatures, this gas appliance should be located out of trafc and away from

furniture and draperies.

• Children and adults should be alerted to the hazards of high surface temperatures and should

stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical

barrier is recommended if there are at risk individuals in the house. To restrict access to a

replace or stove, install an adjustable safety gate to keep toddlers, young children and other at

risk individuals out of the room and away from hot surfaces.

• Clothing or other ammable material should not be placed on or near the appliance.

• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the

replace and shall be installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturers barrier

for this appliance.

• Any grill, panel or door removed for servicing the unit must be replaced prior to operating.

• Installation and repair should be done by a qualied service person. The appliance should be

inspected before use and at least annually by a professional service person. More frequent

cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is

imperative that control compartments, burners and circulating air passageways of the appliance

be kept clean.

• This appliance must not be connected to a chimney ue serving a separate solid fuel burning

appliance.

• It is our policy that no responsibility is assumed by the Company or by any of its employees or

representatives for any damages caused by an inoperable, inadequate, or unsafe condition which

is the result, either directly or indirectly, of any improper operation or installation procedures.

260619-56 100001042

z35

41 3/4”

38 1/4”

34 1/4” 37 1/4”

34 7/8”

27 7/8”

8”

5”

28 7/8”

8”

Figure 1: Front view.

22 3/4”

23 1/4”

7”14”

42 3/8”

Figure 2: Side view.

34 1/8”

28 1/4”

9 3/8”

Figure 3: Top view.

Fireplace Dimensions

The installation must conform with local codes or, in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the National Gas and Propane Installation Code, CSA

B149.1

A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such

a standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or standard for Gas Equipped Recreational Vehicles and Mobile Housing , CSA Z240.4

100001042 z35

260619-56

Figure 4: Common installation examples.

Front of the appliance is an open side of the combustion chamber covered with the glass.

Facing the front of the appliance side from left is the left side of the appliance and side from right is

the right side of the appliance.

Locating the Fireplace

In planning the installation for the replace, it is necessary to determine where the unit is to

be installed, location of vent system and where gas supply piping may be plumbed. Various

installations are possible, such as, into an existing wall, a corner, a built in wall or a wall projection.

Due to high temperatures, do not locate this replace in areas of high trafc or near furniture or

draperies. For places where a second side wall is specied, replace should be accessible for

service

260619-56 100001042

z35

Framing and Finishing

Note: This replace should be in place and venting installed before framing in or building an

enclosure around the unit.

The z35 replace must be framed in as described below or totally enclosed with non-combustible

material, such as facing brick.

If preferred, additional masonry type non-combustible material can be installed above the appliance.

The ﬁnishing material must not interfere with glass door and safety screen removal.

The sides, back and top of the replace can be framed in using conventional lumber. Consult local

building codes for specic requirements.

Due to high temperatures, non-combustible material board, such as cement board or its equivalent,

must be used to sheet in above the replace, extending a minimum of 13” above the replace

opening so that the top of the non-combustible board is level with the top of the standoffs - (Figure

20 on page 15). Standard sheet rock (dry wall) may be used up to the sides of the replace

opening.

A header using two 2 x 4’s must be installed so that the bottom of the header is level with the top

standoffs (Figure 5). This header will support both combustible and non-combustible facing material

above the replace opening.

If backer board is not to be used, other non-combustible material such as tiles may be used. It

is recommended that top sections of the board be a single sheet of calcium silicate board or its

equivalent. Taped and mudded joints may crack due to the elevated temperatures.

Chase Insulation: When installing this replace against a non-insulated exterior wall or chase, it is

recommended that the outer walls be insulated to same degree as other exterior walls. Do not place

replace directly against the insulation. Cover the insulation and plastic vapour barrier with a solid

surface, such as dry wall (sheet rock). Consult local codes. Do not insulate between the top of the

replace and the top of the stand-offs.

100001042 z35

260619-56

2”

20”

53 5/8”

74 3/8”

Figure 8: z35 Corner Installation.

41 3/4”

42 3/8”

Figure 5: Framing front view.

23 1/4”

Figure 6: Right side view.

Figure 7: Isometric framing.

For complete Cool Wall Venting installation instructions, see the installation manual which is

included with the Cool Air Venting Kit.

Framing in the z35

Framing in the z35 and Optional Cool Wall Venting Kit

260619-56 100001042

z35

Note: Position of bottom of the header should be

parallel with the top of the stand-offs (Figure 5).

Note: Each of the exible

vent pipes come to the

customer site compressed

to 3 feet lengths and each

is expandable to 5 feet.

Therefore, the nal position

of the vent register must

take this range into

account when building

supports for the register.

42” Minumum

Vent register

distance is variable

42 3/8”

Figure 9: Framing front view with cool wall kit.

Figure 10: Side view of cool wall kit.

Note: An offset will be

required when using

the Cool Wall Kit.

NOTE: If using the Cool Wall

Vent option, the cool wall vent

must be secured by headers

above and below the vent

(Figure 9).

100001042 z35

260619-56

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pacific energy Cheminée intérieure

Pacific energy

Pacific energy Pacific Wood Insert DESIGN-D Manuel utilisateur

Pacific energy

Pacific energy CASCO Manuel utilisateur

Pacific energy

Pacific energy SUMMIT INSERT SERIES - B Mode d'emploi

Pacific energy

Pacific energy NEO 2.5 INSERT Manuel utilisateur

Pacific energy

Pacific energy SUPER INSERT DESIGN-E SPNE Manuel utilisateur

Pacific energy

Pacific energy GESM.BODYA Manuel utilisateur

Pacific energy

Pacific energy G Series Manuel utilisateur

Pacific energy

Pacific energy SUMMIT WOOD INSERT DESIGN-A Manuel utilisateur

Pacific energy

Pacific energy T5 Manuel utilisateur

Pacific energy

Pacific energy SUPER INSERT DESIGN-E SPNE Manuel utilisateur

Pacific energy

Pacific energy BROADWAY Manuel utilisateur

Pacific energy

Pacific energy FP30AR Manuel utilisateur

Pacific energy

Pacific energy CASCO Manuel utilisateur

Pacific energy

Pacific energy BROADWAY GBWY.BODYA Manuel utilisateur

Pacific energy

Pacific energy FP25 Instructions de montage

Pacific energy

Pacific energy TOFINO i30s Manuel utilisateur

Pacific energy

Pacific energy neo 1.2 Manuel

Pacific energy

Pacific energy ULC S628 Manuel utilisateur

Pacific energy

Pacific energy Alderlea T5 Insert Manuel utilisateur

Pacific energy

Pacific energy ALDERLEA T5 LE Manuel utilisateur

Pacific energy

Pacific energy BRISTOL A Series Manuel utilisateur

Pacific energy

Pacific energy ESPR.BODYA Manuel utilisateur

Pacific energy

Pacific energy SUMMIT INSERT Manuel utilisateur

Pacific energy

Pacific energy Series A Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation

Pacific energy z35 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques