oxic XCAA201 Manuel utilisateur
1
WDR Day/Night 650 TVL
Backfocus Camera
Version2010-A
Oringinal English user Manual. Keep for future use
2
Introduction
Dear Customer,
Thank you for purchasing this product.
This product meets the requirements of the applicable European and national
guidelines. The corresponding declarations and documents can be obtained
from the manufacturer.
To maintain this condition and to ensure risk-free operation, you as the user must
observe these operation instructions!
Before initial start-up, read through the complete operating instructions observing
operating and safety instructions.
All company and product names mentioned in this document are registered
trademarks.
All rights reserved.
If you have any questions, please contact your installer or your local dealer!
Disclaimer
This user manual was prepared with greatest care. If you should notice omissions or
inaccuracies, please inform us about these on the back of this manual given
address.
product or user manual without a previous announcement.
The company is not liable or responsible for direct and indirect subsequent
damages which are caused in connection with the equipment, the performance and
the use of this product.
No guarantee for the content of this document is taken.
3
Important safety instructions
The warranty will expire for damage due to non-compliance with these
operating instructions. We shall not be liable for any consequential loss!
We do not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety-instructions. In
such cases the warranty will expire.
Dear customer,
The following safety instructions are intended not only for the protection of your health,
but also for the protection of the device. Please read through the following points
carefully:
•There are no parts on the inside of the product which need to be serviced. Apart from
this, the license (CE) and the guarantee/warranty will lapse if you open/take the
product apart.
•The product will be damaged even it falls from a low height.
Avoid using the device under the following unfavorable ambient conditions:
•wetness or excessive air humidity
•extreme cold or heat
•direct sunlight
•dust or combustible gases, vapors or solvents
•strong vibration
•strong magnetic fields, such as those found in the vicinity of machinery or
loudspeakers
•the camera should not positioned with opened iris towards the sun -
this can lead to destruction of the sensor.
•the camera may not be installed on unstable surfaces
General safety instructions:
•Do not leave packaging material lying around carelessly. Plastic/ foil/bags and
polystyrene parts etc. could become dangerous toys for children.
•For safety reasons don’t give the camera into child hands due to them being able to
swallow small parts.
•Please do not insert objects through the openings into the device.
4
•Use only accessories which are specified by the manufacturer.
Please do not connect incompatible parts to the device.
•Please pay attention to the safety instructions and user manuals of the other
connected devices.
•Check the device for damages before installation. If this should be the case please do
not use it.
•Please adhere to the operational voltage limitations listed in the technical data. High
voltage could destroy the device and pose a health hazard (electric shock).
During the installation into an existing video surveillance system make sure that all
devices are disconnected from the low and supply voltage circuit.
If in doubt allow a professional electrician to mount, install and wire-up your device.
Improper or make-do electrical connection to the mains does only represent at
threat to you but also to other persons.
Wire-up the entire system making sure that the mains and low voltage circuit
remain separated and cannot come into contact with each other in normal use or
due to any malfunctioning.
5
Table of contents
1. Intended use.............................................................................................................06
2. Explanation of symbols...........................................................................................06
3. Scope of delivery.....................................................................................................07
4. Features and functions ...........................................................................................07
5. Description of device ..............................................................................................07
5.1 Overview – article numbers ..............................................................................07
5.2 Unpacking ........................................................................................................07
6. Mounting...................................................................................................................08
6.1 Power supply....................................................................................................08
6.2 Lens mounting..................................................................................................08
6.3 Mounting of the video cable..............................................................................09
6.4 Mounting of the camera....................................................................................09
7. Rear view..................................................................................................................10
8. OSD...........................................................................................................................11
9. Servicing and cleaning............................................................................................14
9.1 Function test.....................................................................................................14
9.2 Cleaning ...........................................................................................................14
10. Disposal....................................................................................................................14
11. Technical data..........................................................................................................15
6
1. Intended use
The WDR Day/Night 540 TVL Standard Camera is equipped with a high quality image
sensor. It is used for video surveillance in internal areas in connection with a recorder
or monitor.
You can find a detailed description of functions in section “4. Features and functions”.
The product should not become damp or wet. The camera is only for use in dry indoor
areas.
Any other use than that described above can lead to damage to the
product and in addition involve other risks. This does not include
operation for other applications and would in case of doing so the
guarantee and any related liability will lapse. This is also the case if any
unauthorized changes or additions have been made to the product.
Please read through the entire manual carefully before putting this
product into operation. This operating manual contains guidelines that
are important for correct mounting and operating.
2. Explanation of symbols
A flash in the triangle is used if there is danger for the health, e.g. by an
electric shock.
An exclamation mark in the triangle points to an important note in this
user manual which must be minded.
This symbol can be found when you are to be given tips and information
on operation.
7
3. Scope of delivery
•WDR Day/Night 650 TVL Standard Camera
•C-Mount lens adapter ring
•Mounting bracket and screws for camera bracket
•User manual
4. Features and functions
•Sony Effio-Pro newest DSP
•Backlight compensation with high dynamic range (WDR)
•Day/Night camera with removable IR cut filter (ICR)
•2D + 3D DNR Support.
•On-Screen-Menu for easy camera setup (OSD)
•Dual-Video output (2 x BNC)
5. Description of device
5.1 Overview – article numbers
Article Number DUAL POWER AC TYPE
Resolution 650 650
Day/Night
(removable IR cut-filter)
√√
Operating voltage 12VDC/24VAC 110-240VAC
5.2 Unpacking
While you are unpacking the device please handle it with utmost care.
If you notice any damage of the original packaging, please check at first the
device.
If the device shows damages, please contact your local dealer.
8
6. Mounting
6.1 Power supply
Before you start with the installation please make sure that the main voltage and the
nominal voltage of the camera comply together.
MONITOR
VIDEO
POWER
EXT
12VDC/24VAC
DUAL POWER
MONITOR
VIDEO
POWER
EXT
110-240VAC
AC TYPE
(1) DUAL POWER is run by a 12VDC/24VAC power supply. The polarity can be
ignored.
In order to connect a 12VDC power supply (DC Connector 5.5mm x 2.1mm)
to the camera you have to first install the included connector cable. Therefore
you need to press the pins and insert the cable ends into the terminals.
(2) AC type is run by a 110~240VAC power supply (preinstalled cable).
6.2 Lens mounting
The camera is designated for lenses with CS-Mount. A lens with C-Mount
can be mounted with the enclosed lens adapter ring.
Before a lens with C-Mount can be mounted, please make sure that the
lens adapter ring is mounted on the camera. Otherwise you may damage
the image sensor.
9
For lenses with DC-drive the connector for the lens cable is on the right
side of the camera. The lens type is identified automatically by the
camera. A lens with DC-drive is recommended for an optimal image
quality.
Back-Focus adjustment:
6.3 Mounting of the video cable
To connect the video signal of the camera with a monitor or recorder, use a coaxial
cable of the type RG59 with BNC-Connector (male) at the “VIDEO” connector.
The cable length up to the next device should not rise 100 meters.
6.4 Mounting of the camera
For the mounting of the camera, mount the provided socket at the upper or underside
of the camera. For this the plate is aligned with the already predefined screw openings
and fastened with the enclosed screws.
ATTENTION!
During the assembly the camera must be separated from the main
voltage.
CAUTION!
The camera should not be positioned with opened iris towards the sun.
This can lead to the destruction of the sensor.
10
7. Rear view
MONITOR
VIDEO
POWER
EXT
12VDC/24VAC
12VDC Version
MONITOR
VIDEO
POWER
EXT
110-240VAC
110~240VAC Version
(1) OSD menu buttons
(2) Relay output (triggered by motion, max. 60VDC/400mA)
(3) Power Supply (12VDC/24VAC or 110~240VAC)
(4) Status LED (active if power is connected)
(5) BNC Video output (MONITOR)
(6) BNC Video output (VIDEO)
(7) Auto iris DC lens driver connector
Buttons Function
(1) Enter : Enter menu / execute
(2) Up : Navigate upwards
(3) Down : Navigate downwards
(4) Left : Increase value / select option
(5) Right : Decrease value / select option
2
3
1
4
5
1
1
2 2
3 3
4
4
5
5
6 6
7 7
Table des matières
Autres manuels oxic Caméra de sécurité
