Ovation 300C Manuel utilisateur

USER
MANUAL
SOLAR PANEL 300C

Table of contents
Caution!������������������������������������������������������������������������������������������������������������������������������������������������ 3
Introduction������������������������������������������������������������������������������������������������������������������������������������������ 3
Safety instructions ������������������������������������������������������������������������������������������������������������������������������� 3
Installation ������������������������������������������������������������������������������������������������������������������������������������������� 4
Read ‘Safety information’ before installing the xture. ................................................................................4
Fastening the xture to a at surface ...........................................................................................................4
Mounting the xture on a truss .....................................................................................................................4
Securing with a safety cable .........................................................................................................................4
DMX-512 connection/connection between xtures ....................................................................................5
Power connection ..........................................................................................................................................5
Operation ��������������������������������������������������������������������������������������������������������������������������������������������� 6
Control Menu Map .........................................................................................................................................6
Control menu ..................................................................................................................................................7
Main Menu ......................................................................................................................................................7
Addressing ......................................................................................................................................................8
Universal DMX Control ...................................................................................................................................9
RDM control ....................................................................................................................................................9
Rotary Knob function .....................................................................................................................................9
Set dimmer curves .......................................................................................................................................10
DMX Protocol ������������������������������������������������������������������������������������������������������������������������������������� 11
Fixture Cleaning ��������������������������������������������������������������������������������������������������������������������������������� 12
Troubleshooting ��������������������������������������������������������������������������������������������������������������������������������� 12
The xture does not work, no light ..............................................................................................................12
Technical specications ��������������������������������������������������������������������������������������������������������������������� 13

Studio Panel
3hotion.com V5.0
Caution!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires!
Avoid looking directly into the light source!
Wear protective glasses and other PPE (personal protective equipment) when working on or
near the xture.
For your own safety, please read this user manual carefully before you initial start-up.
Follow operating safety precautions and pay attention to warning signs methods and equip-
ment on the user manual.
Indoor use only! To prevent risk of re or shock, do not expose this product to rain or moisture.
IP 20 rating.
The ambient temperature must always be between -5° C and +45° C.
Always make sure you are connecting this product to the proper voltage in accordance with the
specifications in this manual or on the product’s specification label.Make sure it is grounded
when using it!
Unplug mains lead before opening the housing!
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture
and the powercord from time to time.
Make sure to replace the fuse with another of the same type and rating.
Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot
during operation. After use, wait for a cool-down period of at least 10 minutes before handling
or transporting the device.
Every person involved with the installation, operation and maintenance of this device has to
- be qualied
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
Introduction
Thank you for having chosen Solar Panel 300C. You will see you acquired a powerful and versatile de-
vice.
Unpack your item. Before you initial start-up, please make sure that there is no damage caused by
transportation. Should there be any, consult your dealer and do not use the device.
Safety instructions
This device has left our premises in absolutely perfect condition. In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and
warning notes written in this user manual. Always disconnect from the mains, when the device is not in

Studio Panel
4hotion.com V5.0
use or before cleaning it. Keep away children and amateurs from the device! There are no serviceable
parts inside the device. Maintenance and service operations are only to be carried out by authorized
dealers.
Installation
Read ‘Safety information’ before installing the xture.
The xture is designed for indoor use only and must be used in a dry location with adequate ventilation.
Ensure that none of the xture’s ventilation slots are blocked.
Fasten the xture to a secure structure or surface. Do not stand it on a surface or leave it where it can
be moved or fall over. If you install the fixture in a location where it may cause injury or damage if it
falls, secure it as directed in this user manual using a securely anchored safety cable that will hold the
xture if the primary fastening method fails.
Fastening the xture to a at surface
The fixture can be fastened to a hard, fixed, flat surface that is oriented at any angle. Ensure that the
surface and all fasteners used can support at least 10 times the weight of all xtures and equipment to
be installed on it.
Fasten the xture securely. Do not stand it on a surface or leave it where it can be moved or fall over. If
you install the xture in a location where it may cause injury or damage if it falls, secure it as directed
below with a securely anchored safety cable that will hold the fixture if the primary fastening method
fails.
Mounting the xture on a truss
The xture can be clamped to a truss or similar rigging structure in any orientation. When installing the
xture hanging vertically down, you can use an open-type clamp such as a G-clamp. When installing in
any other orientation, you must use a half-coupler clamp that completely encircles the truss chord.
To clamp the xture to a truss:
1. Check that the rigging structure can support at least 10 times the weight of all xtures and equip-
ment to be installed on it.
2. Block access under the work area.
3. Fold the legs of the mounting bracket together and bolt a rigging clamp securely to the mounting
bracket. The bolt used must be M10, grade 8.8 steel min-
imum. It must pass through both mounting bracket legs
and be fastened with a self-locking nut.
4. Working from a stable platform, hang the fixture with its
clamp on the truss and fasten the clamp securely.
5. Secure the xture with a safety cable as directed below.
Securing with a safety cable
Secure the xture with a safety cable (or other secondary attachment) that is approved for the weight
of the xture so that the safety cable will hold the xture if a primary attachment fails.

Studio Panel
5hotion.com V5.0
Loop the safety cable through the eyebolt in the back of the fixture and around a secure anchoring
point. Do not loop the safety cable around the xture’s mounting bracket only, as this will leave the x-
ture unsecured if it separates from the bracket.
DMX-512 connection/connection between xtures
Occupation of the XLR-connection:
1. Group
2. Signal (-)
3. Signal (+)
DMX OUT
1. Group
2. Signal (-)
3. Signal (+)
DMX IN
If you are using controllers with this occupation, you can connect the DMX-output of the controller di-
rectly with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers
with other XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture.
Always connect one output with the input of the next xture until all xtures are connected.
DMX-512 connection with DMX terminator:
For installations where the DMX cable has to run a long distance or is in an electrically noisy environ-
ment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing
corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug
with a 120 resistor connected between pins 2 and 3, which is then plugged into the output XLR socket
of the last xture in the chain.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω
resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the
last xture.
Power connection
Power Requirements
The Solar Panel 300C luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire
contains an auto-ranging power supply.
Power linking between xtures:
The xture with powercon in and out socket. Connect the power out to the power in socket in the next
xture till all are connected.
Caution: maximum power linking - 6 units.
Connection with the mains:
Connect the device to the mains with the enclosed power supply cable.
The occupation of the connection cables as below:

Studio Panel
6hotion.com V5.0
Cable color Connection International
Brown Live L
Blue Neutral N
Yellow/green Earth(Ground)
Operation
The Solar Panel 300C can operate in three different modes. This next section will detail the differences
in the operating modes.
Control Menu Map
Default setting in bold.
MAIN MENU LEVEL 1 LEVEL 2 LEVEL 3 FUNCTION INSTRUCTION
DMX 001-512 DMX address setting
Mode
DMX 2/7/11CH DMX channel mode
Auto Program 001-005 Preset programs
Speed 001-009 Programs speed
Maunal
Red 000-255 Red dimmer 0 - 100%
Green 000-255 Green dimmer 0 - 100%
Blue 000-255 Blue dimmer 0 - 100%
Warm 000-255 WW dimmer 0 - 100%
Cold 000-255 CW dimmer 0 - 100%
Strobe 000-255 Strobe, speed increasing
Dimmer
Curve 0.3-3.0 Dimmer curves adjustment
Mode
Standard Dimmer mode, Standard
Stage Dimmer mode, Stage
TV Dimmer mode, TV
Architecture Dimmer mode, Architecture
Theatre Dimmer mode, Theatre
Studio Less power, lower fan speed
Turbo Trubo mode, 300W output max.
Custom
Fade in
(150 ms~2230 ms) Custom dimmer curve
Fade out
(150 ms~2230 ms)

Studio Panel
7hotion.com V5.0
Advance
Authorization On/Off
Advanced settings/calibration(Only
qualified technicians should
perform this function. Inqure your
local dealer for password.)
Signal Priority DMX DMX signal priority setting
Signal Hold On/Off Run if signal cut
RDM On/Off RDM function on/off
Screen Timeout 30S Display shut off time
Never
Screen Brightness 25-100% Display brightness
Dimming Freq 1.20-24.00KHz adjustable Dimmer frequency setting
Software version xxx Software version
Reset Yes/No System reset
Reverse Yes/No Display reverse 180 degree
Control menu
The information menu will appear after the xture is switched on. In this menu, the following status is
displayed:
Main Menu
Press the MENU button to enter the Main Menu interface.

Studio Panel
8hotion.com V5.0
Menu
DMX
Advance
Mode
Dimmer
Addressing
All xtures should be given a DMX starting address when using a DMX signal, so that the correct xture
responds to the correct control signals. This digital starting address is the channel number from which
the xture starts to listen to the digital control information sent out from the DMX controller. The allo-
cation of this starting address is achieved by setting the correct number on the display located on the
base of the device.
You can set the same starting address for all xtures or a group of xtures, or make different address
for
each xture individually.
If you set the same address, all the units will start to listen to the same control signal from the same
channel number. In other words, changing the settings of one channel will affect all the xtures simulta-
neously.
If you set a different address, each unit will start to listen to the channel number you have set, based on
the quantity of control channels of the unit. That means changing the settings of one channel will af-
fect only the selected xture.
In the case of the Solar Panel 300C, which is 2/7/11 channels fixture. If you set, for example, the ad-
dress in the 2 channel mode to channel 3, the device will use the channel 3-4 for control.
Note: After switching on, the device will automatically detect whether DMX 512 data is received or
not. If there is data received at the DMX input, you will see the DMX indicator light in green.

Studio Panel
9hotion.com V5.0
Universal DMX Control
This function allows you to use a universal DMX-512 controller to control the dimmer and strobe. A
DMX controller allows you to create unique programs tailored to your individual needs.
RDM control
The Solar Panel 300C can communicate using RDM (Remote Device Management) in accordance with
ESTA’s American National Standard E1.20-2006: Entertainment Technology RDM Remote Device Man-
agement Over DMX512 Networks.
RDM is a bi-directional communications protocol for use in DMX512 control systems, it is the open
standard for DMX512 device conguration and status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without affecting ex-
isting non-RDM equipment. It allows a console or dedicated RDM controller to send commands to and
receive messages from specic xtures.
With RDM function, you can set the DMX address of your fixtures remotely. This is especially useful
when the device is installed in a remote area.
Each Solar Panel 300C has a factory set RDM UID (unique identication number).
Note: Before operation, enable RDM function in Advanced settings.
Menu
DMX Mode
Dimmer Advance
Rotary Knob function
The knob in the rear panel of the Solar Panel 300C act as multi function. Including rotary control of
dimmer, rotary control of dimmer, up/down/enter function function.
Dimmer function:
1. Press the MENU button to enter the main menu.
2. Press the UP or DOWN button to select Mode menu and press ENTER.
3. Press DOWN menu and select Manual sub menu.
4. Press ENTER and select Brightness or Strobe in third menu.
5. Rotate the rotary knob to control the dimmer(right stop = maximum output, left stop = zero output),
or strobe(right stop = maximum strobe, left stop = no strobe).

Studio Panel
10hotion.com V5.0
Note: Rotary dimmer or strobe function works in information Menu and Mode-Manual menu.
Up, Down, Enter function:
The knob can also act as up, down and enter function.
1. Press the MENU button to enter the main menu interface.
2. Right rotation = Down, left rotation = Up, press = Enter function.
Set dimmer curves
This function allows you to select preset dimmer curves as well as custom dimmer curves.
Menu
DMX Mode
AdvanceDimmer
Menu>Dimmer
Curve
1.0
Mode
Standard
Stage
TV
Architecture
Theatre
To set preset dimmer curves:
1. Press the MENU button to enter the main menu.
2. Press the UP or DOWN button to select Dimmer menu and press ENTER.
3. Press DOWN menu and select Mode sub menu.
4. Select disired dimmer mode.
Custom dimmer curves:
1. Press the MENU button to enter the main menu.
2. Press the UP or DOWN button to select Dimmer menu and press ENTER.
3. Press DOWN menu and select Mode sub menu.
4. Press the UP or DOWN button to select Custom menu and press ENTER.
5. Adjust fade in and fade out time to customize yout dimmer curves. Time vary from 150 ms to 2230
ms.
Table des matières

















