Outwater DGL-RFKY-CAB-SL Manuel utilisateur
DIGITAL CABINET LOCK
DGL-RFKY-CAB-SL
USER GUIDE
24 River Road • Bogota, NJ 07603 | Phone: 1.800.631.8375 | www.outwater.com
Page 2Outwater Industries, Inc. assumes no liability for improper installation.
PROGRAMMING INSTRUCTIONS
LOCK INTERFACE OVERVIEW
Page 3Outwater Industries, Inc. assumes no liability for improper installation.
KEY GUIDE
INITIALIZING LOCK(S)
REGISTER MASTER KEY
• Provides highest level management access
• Registers master key(s) and master code
• Each lock accepts only (1) master key
• Provides second level management access
• Registers permanent code and user key
• Each lock accepts only (1) supervisor key
• Provides third level management access
• Each lock accepts up to (5) user keys
Master Key (Red) Supervisor Key (Blue) User Key (Black) [OPTIONAL]
Disassemble the lock, connect back body with front body to keep power supply and press the red button to reset the lock.
Start at locker #1. Touch the Master Key
(Red) to the key reader for one full second.
A three tone beep will be heard and
the green LED light will ash thrice.
This lock is programmed with the
Master Key.
Test the programming by touching the
Master Key (Red) to the key reader of
lock. If programming is successful the
lock will operate.
Page 4Outwater Industries, Inc. assumes no liability for improper installation.
REGISTER SUPERVISOR KEY(S)
Go to a lock previously programmed with
existing Master Key, and is under a locked
state.
Touch the Master Key (Red) to the key
reader for one full second. The lock will
unlock and the green LED light will ash.
While LED light is ashing, touch each
of the Supervisor Key(s)(Blue) to the key
reader at a time. A single tone beep will
be heard each time a new key is touched
to the lock indicating acceptance.
When nished touching all Supervisor Keys
(Blue), end programming by touching the
Master Key (Red) to the key reader.
Test the programming by touching the
Supervisor Key (Blue) to the key reader
of lock. If programming is successful, the
lock will operate.
REGISTER/CHANGE MASTER CODE
Go to a lock previously programmed with
existing Master Key, and is under a locked
state.
Test the programming by key in master
code of lock. If programming is successful,
the lock will operate.
While LED is ashing, Press:
(any 1-9 digit code). A two tone beep will
be heard and the lock will lock to indicate
acceptance.
Touch the Master Key (Red) to the key
reader for one full second. The lock will
unlock and the green LED light will ash.
*#
Page 5Outwater Industries, Inc. assumes no liability for improper installation.
FOR LOST OF STOLEN KEY(S)
For Lost Master Key
For Lost Supervisor Key(s) or Deleted Master Code
Disassemble the lock, connect back body with front body to keep power supply and press the red button to reset the lock.
NOTE: Lock will not reset by removing the batteries.
Under locked state. Touch the Master Key (Red) to the
key reader for one full second. The
lock is unlocked, a single tone beep
will be heard and the green LED
light will ash.
While the green LED light is ashing,
touch the Master Key (Red) to the
key reader for one full second again,
a three tone beep will be heard and
the red LED light will ash thrice, the
existing Supervisor Key and Master
Code is deleted.
Page 6Outwater Industries, Inc. assumes no liability for improper installation.
OPTIONAL PROGRAMMING
KEYBOARD QUIET MODE
To Enable Keyboard Quiet Mode:
To Disable Keyboard Quiet Mode:
Keyboard quiet mode is an option where the sound can be activated or deactivated when pressing the keyboard.
Perform steps 1 through 3 of "To Enable Keyboard Quiet Mode" as shown above.
Under locked state. Touch the Master Key (Red) to the key
reader for one full second. The lock will
unlock and the green LED light will
ash.
While the green LED light is ashing, touch
the Master Key (Red) to the key reader for
one full second again, a two tone beep will
be heard and the green LED light will ash
twice, the lock is locked and keyboard quiet
mode is active.
While the green LED light is ashing, touch
the Master Key (Red) to the key reader for
one full second again, a single tone beep
will be heard and the green LED light will
ash once, the lock is locked and keyboard
quiet mode is deactivated.
While LED is ashing, Press: + , the
green LED light will keep ashing.
*#
Page 7Outwater Industries, Inc. assumes no liability for improper installation.
ALARM QUIET MODE
To Enable Alarm Quiet Mode:
To Disable Alarm Quiet Mode:
Alarm quiet mode is an option where the sound can be activated or deactivated when the lock is under incorrect operation.
Under locked state.
Under locked state.
Touch the Master Key (Red) to the key
reader for one full second. The lock will
unlock and the green LED light will
ash.
Touch the Master Key (Red) to the key
reader for one full second. The lock will
unlock and the green LED light will
ash.
While the green LED light is ashing, touch
the Master Key (Red) to the key reader for
one full second again, a two tone beep will
be heard and the green LED light will ash
twice, the lock is locked and alarm quiet
mode is active.
While the green LED light is ashing, touch
the Master Key (Red) to the key reader for
one full second again, a single tone beep
will be heard and the green LED light will
ash once, the lock is locked and alarm
quiet mode is deactivated.
While LED is ashing, Press: + , the
green LED light will keep ashing.
*#
While LED is ashing, Press: + , the
green LED light will keep ashing.
*#
Page 8Outwater Industries, Inc. assumes no liability for improper installation.
LOCKER USE WORKING MODE (ONE TIME CODE)
ENABLE ONE-TIME CODE WORKING MODE
ONE-TIME CODE USE INSTRUCTION
TO OPERATE WITH A ONE-TIME CODE
Make sure both S1 & S2 are moved to 1
Under locked state. Lock is locked, one-time code is registered.
Press: (any 1-9 digit code).
A two tone beep will be heard and the red
LED light will ash twice.
*#
1) Find an available lock.
2) Press: (any 1-9 digit code).
1) Same as lock.
2) Press: (any 1-9 digit code).
# #
To Lock: To Unlock:
NOTE: If an incorrect code is entered four consecutive times, the lock will alarm for one full minute, or until a registered
Master Key or Supervisor Key is touched to the key reader.
Page 9Outwater Industries, Inc. assumes no liability for improper installation.
TO OPERATE WITH MASTER KEY
TO OPERATE WITH SUPERVISOR KEY
TO OPERATE WITH MASTER CODE
To Lock:
To Lock:
To Lock:
To Unlock:
To Unlock:
To Unlock:
NOTE: If an incorrect iB key attempts to unlock the lock, there is no reaction from the lock.
NOTE: If an incorrect iB key attempts to unlock the lock, there is no reaction from the lock.
Touch the Master Key (Red) to the key reader.
Touch the Supervisor Key (Blue) to the
key reader.
Enter Master Code + Enter Master Code +
Touch the Supervisor Key (Blue) to the
key reader.
Touch the Master Key (Red) to the key reader.
NOTE: If an incorrect code is entered four consecutive times, the lock will alarm for one full minute, or until a registered
Master Key is touched to the key reader.
##
Page 10Outwater Industries, Inc. assumes no liability for improper installation.
STATION USE WORKING MODE (PERMANENT CODE)
ENABLE PERMANENT CODE WORKING MODE
ENABLE PERMANENT CODE WORKING MODE
Make sure S1 is moved to 2, S2 is moved to 1
Under locked state. Unlock the lock with Supervisor Key (Blue) or Master Code, green LED light will ash.
Press: (any 1-9 digit code).
While LED light is ashing. Lock is locked and a two tone beep
will be heard. Permanent code is
now registered.
Test the programming by entering
the Permanent Code. If programming
is successful, the lock will operate.
*#
Table des matières
