Outsunny A33-028RD Manuel utilisateur
ASSEMBLY & INSTRUCTION MANUAL
INaab045_CA_FR
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Stand-Up-Paddle Board-Set
OWNER’S MANUAL
(All Around SUP Board)
Thank you for choosing this inflatable stand up saddle board (ISUP).
To get the best out of your new product you must read and fully un-
derstand this user manual.
Get professional instructions before you go stand up paddle boarding.
Always be extremely careful when using this product. Only use this
product if you are in good physical and mental shape. Due to safety
precautions, ISUP’s should only be used on and above water surfac-
es. While using this product, you’re responsible for your own and
others safety. Never go stand up paddle boarding if you are not famil-
iar with the area and surroundings. Never go paddling in strong or
offshore winds. Never go paddling on an outgoing tide or strong tidal
currents.
All persons should wear a suitable buoyancy aid (life jacket/personal
floatation device) when using an ISUP. Be aware that some countries
make it is a legal requirement to wear a buoyancy aid that complies
with their national regulations.
Table Of Contents
ISUP Structure Terminology --------------------------------------------------------------------------------------------------------3
PACKING LIST -------------------------------------------------------------------------------------------------------------------------------------3
SET-UP PREPARATION-------------------------------------------------------------------------------------------------------------------4
ALU telescopic ISUP paddle -------------------------------------------------------------------------------------------------------7
LEAK DETECTION AND REPAIR-------------------------------------------------------------------------------------------------8
INSTRUCTION FOR CARE AND STORAGE---------------------------------------------------------------------------9
FOR YOUR SAFETY------------------------------------------------------------------------------------------------------------------------- 10
WARNING -------------------------------------------------------------------------------------------------------------------------------------------11
-2-
ISUP Structure Terminology
Tri fin set: One centre fin and
two small fins on the side.
PACKING LIST
● Stand up paddle board
● Three shafted aluminium adjustable oar
● Hand pump w/ pressure gauge
● Valve wrench
● Repair kit
● Professional carry bag
● Middle fin
● Instruction manual
-3-
SET-UP PREPARATION
1.Remove the board from the packaging.
Choose a smooth and clean surface and unroll your board so it lays
top-side up.
2.Valve operation
Follow the instructions below to inflate and deflate the ISUP properly.
The inflation valve is near the nose of the board. To close off the
valve for inflation, ensure the centre valve pin is in the UP position.
For deflation, press the valve pin so it is in the DOWN position.
Be careful of any sand or debris around the valve area when deflating
- small particles could become airborne with the release of the air
pressure.
Always lock the valve cover over the stem when in use. This will pre-
vent accidental air release and any particles getting into the openings.
-4-
3.ISUP Board inflation Steps
a.Unscrew the valve cap and press down on the pin to open the
valve. Let the air flow naturally into the product, then press down on
the pin again to close the valve (in the ‘UP’ position).
b.Make sure the pump hose is connected to the ‘inflate’ outlet.
c.Attach the pump hose with a half twist clockwise onto the valve.
d.Start pumping air into the board by sliding the piston up and down.
Inflate until you reach the required pressure. Minimum 12psi for
proper ISUP operation and a maximum of 15psi for this product.
e.After inflation, tighten the valve cap, so the board stays secure.
4.Fin installation
The two side fins are fixed onto the product. Once the board is
inflated, slide in the middle fin to the base and insert the fixed pin.
-5-
5. Inflation tips and precautions
DO NOT use an air compressor – if your board gets damaged from
over inflation, it will void your warranty.
After a few days, the pressure could decrease due to temperature
change – add a few more pumps of air.
Before using, inflate the board for a full 24 hours to ensure the board
is secure. If you see a consistent decrease in air pressure, follow the
instructions for leak detection in the repair section of this manual.
DO NOT over inflate this board – the maximum pressure should be
15 psi. To ensure the pressure is good, check the chambers are firm
by pressing on them.
DO NOT pump to a high pressure and expose the board to direct sun-
light. If the board is in a warm environment, slightly deflate the board
– the heat from the sun will increase the internal pressure. When pad-
dling, the cold water could cause a slight loss in chamber pressure. It
is recommended to carry a pump to use when necessary.
Put the four buckles on the seat into the D-ring of the paddle.
-6-
ALU telescopic ISUP paddle
Your board paddle comes in three pieces. To build the paddle, hold
the button in while sliding the pieces together until they click into
place. The last section (top) of the paddle is adjustable. To find the
ideal height for your paddle, start by building the paddle so it is 6
inches taller than your own height. From this point, adjust the top sec-
tion up or down until the length is comfortable for you. a longer paddle
is better suited for a smooth, easier paddling motion. A shorter paddle
is good for performance or competition riding.
After closing the button, if the adjustable section is a little loose,
tighten the screw properly using a screwdriver.
Features:
Adjustable length from 165-205 cm
Light and FLOATING: 960g
Shaft of 29 and 27mm in alloy 6005-T6
Compact: Removable in 3 parts of 79cm
-7-
LEAK DETECTION AND REPAIR
Air Leak Detection
If the board is losing air pressure which isn’t caused by cold tempera-
tures, check the board for leaks starting with the valves. A leaking
valve is rare – if this does happen, we will send a replacement. To
find a leak, it is recommended mixing soap and water in a spray
bottle, then spray around the valve. If bubbles appear, check the
valve seating and base to ensure it is screwed tight. If the problems
persist, it is best to get a new valve.
If the board is losing air and there is no issue with the valves, it could
be a small puncture. Spray around the board until air bubbles appear
– mark the position of the leak. If there are no air bubbles, inflate the
board to its maximum capacity and listen for any leaks. If you can
narrow the area of the puncture, spray the board so you can identify
where the leak is.
Repair Kit
Punctures less than 1/8” can be repaired without a patch. Deflate your
board, then clean and dry the area that needs repairing. Apply a small
drop of glue to cover the puncture – let it dry for 12 hours.
If the punctures are bigger, use the patches in the repair kit and follow
these steps:
● Ensure the board is fully deflated, dry and laying flat.
● Cut a patch that is two inches bigger than the tear on all sides.
● Use alcohol to clean the repair area that needs repairing.
● Apply three coats of adhesive to both the patch and board. Wait 5
minutes between each coat.
● Place the patch over the tear – the adhesive will react quickly, so
ensure the positioning is accurate. Use the roller to keep the patch flat
and even.
● Wait 24 hours before inflating the board.
-8-
INSTRUCTION FOR CARE AND STORAGE
ISUPs are easy to transport and store – just follow these steps:
● Before storing, rinse the board and let dry completely to prevent
mildew.
● Do not use harsh chemicals when cleaning – it is best to clean with
mild soap and fresh water.
● The board can be stored inflated or deflated. If deflating, it is recom-
mended to use the provided bag when storing.
● If storing the board outdoors, keep it off the ground and use a cover
to keep it from direct sunlight.
● Hanging the board is not recommended.
● Do not store above 66℃/150℉or below-23℃/-10℉.
● Store in a clean and dry place.
● When storing your board deflated, it is best to leave it loosely rolled
or unrolled.
● If the fins become bent, place them in boiling water to soak for a
few minutes or use a hairdryer, before bending them back to position.
-9-
FOR YOUR SAFETY
-10-
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Manuels Bateau populaires d'autres marques
Raymarine
Raymarine ST70 Instrument Manuel utilisateur
Pro-Line Boats
Pro-Line Boats Pro Line 19 Sport Manuel utilisateur
Jeanneau
Jeanneau CAP CAMARAT 8.5 CC Manuel utilisateur
Tiara Yachts
Tiara Yachts C49 2024 Manuel utilisateur
Monterey Boats
Monterey Boats Sport Yacht 330 Manuel utilisateur
J
J 105 Manuel utilisateur
PURSUIT
PURSUIT OS 335 Manuel utilisateur
Boston Whaler
Boston Whaler CONQUEST 345 Manuel utilisateur
Jeanneau
Jeanneau SUN ODYSSEY 41 DS Manuel utilisateur
Meridian
Meridian 490 Pilothouse Manuel utilisateur
Advanced Elements
Advanced Elements AdvancedFrame Expedition AE1009 Manuel utilisateur
Robo Marine Indonesia
Robo Marine Indonesia GEOMAR Manuel utilisateur
