OSS OSS-CPCIe3-3U-10GbE-x4-QUAD Manuel utilisateur
INSTALLATION GUIDE
OSS-CPCIe3-3U-10GbE-x4-QUAD
OSS-CPCIe3-3U-10GbE-x4-QUAD
www.onestopsystems.com
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 2
Table of Contents
1Getting Started .............................................................................................................................................................. 3
2Unpacking ...................................................................................................................................................................... 3
3Description of Parts........................................................................................................................................................ 4
4Module Installation........................................................................................................................................................ 5
5SFP module and Cable Installation ................................................................................................................................. 7
5.1 Supported SFP and SFP module ................................................................................................................................................................ 7
6Turning ON the Device ................................................................................................................................................... 8
7LED Panel Indicator ........................................................................................................................................................ 8
8Verify Device Installation ............................................................................................................................................... 9
8.1 Linux.......................................................................................................................................................................................................... 9
8.1 Windows ................................................................................................................................................................................................. 11
9Troubleshooting............................................................................................................................................................14
9.1 Device is not detected or recognized ...................................................................................................................................................... 14
9.2 Device is recognized but the front LED indicator is not coming ON ........................................................................................................ 14
9.3 Intel82599 devices are showing UP with a Yellow Exclamation mark ..................................................................................................... 14
9.4 Broken OSS-529 board ............................................................................................................................................................................ 14
10 Contacting Technical Support ........................................................................................................................................15
10.1 Returning Merchandise to One Stop Systems ................................................................................................................................... 15
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 3
1 Getting Started
This installation guide tells you step by step how to install the module. You will find instructions for the following procedures:
Unpacking
Description of Parts
Module Installation
SFP module and Cable Installation
Turning ON the Device
SFP module and Cable Installation
LED Panel Indicator
Verify Device Installation
2 Unpacking
Check and identify the standard supplied item. Inspect the card / module to make sure it is free from physical
defects / damages.
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 4
3 Description of Parts
Side
Front
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 5
4 Module Installation
1. Turn the chassis off and unplug the chassis from AC power.
2. Before inserting the module, inspect the chassis slot to ensure there aren’t any bent pins in the slot connectors.
3. Set the injector /ejector handle in down position.
Caution:
To avoid damaging the module, do not touch exposed board end connectors or components on the printed circuit board when
installing the module.
4. Slowly insert the module in the chassis slot by placing the module card edges into the top and bottom card guides.
With the injector/ejector handle in the down position, carefully slide the module to the rear of the chassis.
Caution:
Ensure that the module is aligned perpendicularly to the chassis as you begin sliding it in. Otherwise, it’s possible for components
on the module (or on adjacent modules) to be damaged by contact between modules.
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 6
5. When you begin to feel resistance from the backplane connectors, push up on the injector/ejector handle to complete
insertion of the module and latch it into place.
6. Secure the module front panel to the chassis using the captive front panel mounting screws. The module has two
captive mounting screws.
a. 1st mounting screw on top
b. 2nd mounting screw (bottom) beneath the injector/ejector
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 7
5 SFP module and Cable Installation
Carefully insert SFP+ Cable (Fiber or Cat6) to any available port on the module.
5.1 Supported SFP and SFP module
What are the SFP+ and SFP module requirements for the Intel® Ethernet Converged Network Adapter X520 Series?
Check Intel website for further information on the supported SFP and SFP modules.
https://www.intel.com/content/www/us/en/support/articles/000005528/network-and-i-o/ethernet-products.html
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 8
6 Turning ON the Device
Once the SFP modules are inserted correctly, you can turn ON the expansion unit.
After the expansion unit is powered UP, the LED located on the front module will illuminate depending on the link connection (either 1G or
10G).
7 LED Panel Indicator
10g: Indicates 10G link
1g: Indicates 1G link
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 9
8 Verify Device Installation
8.1 Linux
On Linux operating system, to verify or check if the device is detected or not, type the command below on the terminal window
$ lspci –tv | grep 82599
See output below, four Intel 82599ES are detected.
$ lspci –D | grep ‘Network\|Ethernet’
See output below, four Intel 82399ES are detected
To find out the device assigned name, type the command below on the terminal window.
$ lspci - c network –businfo
See output below, four 82599ES are detected and each has their corresponding device name (i.e. enp9s0f0)
One Stop Systems
OSS-CPCIe3-3U-10GbE-x4-QUAD 10
The following two photos below represent the device slot address /B/D/F (Bus#, Device#, Function#) and its corresponding physical SFP port
on the card.
The OSS-PXIE-10GBe-QUAD uses a PLX PEX 8732. You can check or query the PEX 8732 by using the command below on the terminal window.
$ lspci –v | grep –I ‘PEX 8732’. See output below
Table des matières
Autres manuels OSS Adaptateur
