Osmio Clarity Manuel utilisateur

Osmio Clarity

Gravity Water Filter System

User Manual

Telephone: 0330 113 7181

Email: [email protected]

The Osmio Clarity uses the best performing gravity water filter elements on

the market we know of, the Coldstream Sentry filters made in the UK. The

Housing is made using borosilicate glass and with mango wood stand and

lid, making it a beautiful and functional shrine to your blessed water for your

home. Recommend for households up to 4 people. Filters are recommended

to change every 6 months, but it depends on water quality. Please note, the

filters do not reduce calcium and magnesium which causes scale in kettles.

Please see the test reports below to find out what it reduces.

Introduction

TAKE NOTE! This item is made of glass. There are holes that have

been diamond drilled and this creates small shards of glass. The

holes are sealed from both sides with the gaskets. The system

must be brushed or washed to ensure any microscopic glass

shards are cleaned before the system is used.

KEEP OUT OF REACH OF SMALL CHILDREN

Important Notice:

The holes for the two filters must be

covered by gaskets on BOTH sides.

The hole for the tap has gaskets for

both sides.

It is important to note that tiny

shards of glass can come off during

initial set up or during filter chang-

es.

Please ensure that after the system

is brushed and cleaned (to remove

any possible shards) after the filters

have been installed, every time they

are changed, and when the tap is

installed, or removed and

reinstalled.

Two Coldstream Sentry Filters - these will come with two

gaskets and a wing nut each.

One 304 Stainless Steel Spigot Tap - this comes with two

silicone rubber gaskets, two Stainless Steel gasket covers,

one tightening nut and a mini-gauze to filter the water

before it comes out the tap.

The Clarity Housing Lid

Two Glass Bowls (upper and lower reservoirs)

Mango Wood Stand

Dimensions

A - 204 mm

B - 660 mm

C - 540 mm

D - 240 mm

E - 135 mm

Unpacking - the contents

Before Assembly

Cleanliness is paramount. Ensure that you wash your hands or wear

rubber gloves before commencing. Carefully unpack the box and

familiarise yourself with all the components. Carefully clean the glass

bowls. Ensure there are no shards of glass.

Choose the location for the housing

Choose a cool, dry location with a flat and steady surface. Please note

that if the system is in direct sunlight, this can cause the water to receive

lovely energy from the sun, but if left for a long time will make the water

go bad!

Installation Step 1: Install the Tap

From the outside, insert the tap thread through the hole in the lower reser-

voir. From the inside of the reservoir; Place the second silicon gasket over

the thread, remove the protective film from the stainless steel washer before

placing this over the thread and ensure it is correctly seated.

Using your fingers, tighten the nut onto the thread, ensuring the tap is cor-

rectly orientated. Holding the tap in place, tighten the in inside until the sili-

con gaskets match the shape of the reservoir inside and out. Do not

over-tighten beyond this point. Usually it is not necessary to use a spanner

to make the nut really tight. Most people can do it by hand.

Unscrew the nut from the stain-

less steel tap. Remove the protec-

tive film (if applicable) from the

outer stainless steel washer and

place it onto the tap thread.

Ensure the concave shape is ori-

entated to match the silicone

grommet that is to be fitted next.

Place a silicon gaskets onto the

tap thread and push down to rest

against the washer.

TAKE NOTE! Fitting the tap for the first time (or

when refitting the tap) can cause very small

fragments of glass to shed off.

After fitting the tap, ensure you wipe the area

and bowl clean with a dry cloth and also rinse

the bowl with water.

Glass Lower Reservoir

Tap

Gasket

Cover

Rubber Silicone

Gaskets

Gasket

Cover

Nut

PLEASE NOTE

If you have any water coming from between the glass and the gaskets it

normally indicates the nut needs further tightening.

Please note the tap lever should be closed before the lower reservoir fills

with water.

Glass Lower Reservoir Installation Step 2:

Install the Filters

• First insert one rubber

gasket through the filter

stem and place all the

way to the end of the

filter.

• Insert the filter cap thread

through one of the holes

in the base of the top

reservoir.

• While holding the filter,

(See FIG 2) place the

second washer over the

stem and use the wing nut

to tighten it up.

• Both gaskets are used for

the filter. There must be

one of either side of

the glass to ensure any

shard areas are covered

over.

• Do not over tighten the

wing-nut as this will

cause the glass to crack

or for the wing nut to

cross thread.

• Repeat the above for the

second filter.

FIG: 1 - Two gaskets must be

either side of the glass.

FIG: 2- Use both hands and the

stand to assemble the two

filters

Installation Step 3: Flushing the filters

Make sure the tap is in the closed position. This is when the lever is at an

angle to the tap (not in the line with the tap).

• Fill the upper tank to the top with water using a separate jug, bottle or

other container. If you are not using mains treated water, ensure that the

water used is in the very least running clear before use (unless if

needed in disaster and emergency situations).

• Usually within 10 minutes or much sooner, the water will drip

through the ceramic filter.

• Check that the water is dropping from the filters themselves, and not

between the rubber gaskets that make the seal between the filter and

the two holes in the upper reservoir.

• Wait now for 1 hour and then discard then open the tap and discard the first

filtered batch of water. Then repeat the process of filling the upper

reservoir. After this has come through the water is ready to use.

• The maximum flow will be reached when the filter is completely

saturated and all the air has been primed out. Ceramic contains many

air pores after manufacturing and it will take up to 5 full cycles for trapped

air to escape completely and maximum flow to be achieved.

• When filling the upper tank, take care not to overfill. The water level in

the upper tank must not exceed the empty volume of the lower tank to

prevent the joint from spilling between the tanks.

For the initial filter of the filter there may be carbon or ce-

ramic residue there. The filter system also does not reduce

more than approximately 30% of limescale so white particle

build up can happen because of that. Ensure you regularly

clean your lower reservoir or as required.

Filter Changing & Cleaning

• If after months of use the flow decreases, it may be possible to

extend the life of the filter and improve the flow by cleaning the

Coldstream Sentry Ceramic Filter Candle. It is recommended to change the

filters every 6 months.

• Carefully remove candle from the unit and handle it as any fragile

ceramic. Using a new and clean soft toothbrush or soft scouring pad,

scrub the filter under running water or in a bowl of water.

• Always brush away from threaded mount, taking care not to

contaminate the mount. Never use soap, detergents nor steel wool.

Be sure to follow the process in Step2 for reinstalling the filters. If you

accidentally drop the candle and it did not brake, to ensure the integrity do the

following test. First the filter needs to be air dried for at least 24 hours.

Submerge it into water container while holding a finger over the outlet to keep

the air inside. If there is a crack the trapped air would exit through it and you

would see bubbles indicating replacement.

Housing cleaning

• Vinegar or citric acid with a damp cloth works great to clean off any

limescale that would build up over time. It is recommend to clean the glass

upper and lower reservoir frequently to prevent algae and limescale build up.

System maintenance

Autres manuels pour Clarity

Table des matières

Autres manuels Osmio Système de filtration d'eau

Osmio

Osmio Fusion Manuel utilisateur

Osmio

Osmio Clarity Manuel utilisateur

Osmio

Osmio Zero Manuel utilisateur

Osmio

Osmio EZFITPRO Series Manuel utilisateur

Osmio

Osmio Infinity Hydroxy Manuel utilisateur

Osmio

Osmio Ecopure Eco-8 Manuel utilisateur

Osmio

Osmio EZFITPRO-300 Manuel utilisateur

Osmio

Osmio EZFITPRO Series Manuel utilisateur

Manuels Système de filtration d'eau populaires d'autres marques

Wisy

Wisy LineAir 100 Manuel utilisateur

Schaffner

Schaffner Ecosine FN3446 Series Manuel d'utilisation

Pentair

Pentair FLECK 4600 SXT Guide de l'utilisateur

H2O International

H2O International H20-500 Manuel utilisateur

Renkforce

Renkforce 2306241 Manuel utilisateur

Neo-Pure

Neo-Pure TL3-A502 Manuel utilisateur

FLTR

FLTR OBF Manuel utilisateur

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuel utilisateur

Applied Membranes

Applied Membranes W-G844EM Manuel utilisateur

BEGA

BEGA 116 Manuel utilisateur

WATA

WATA Standard Manuel utilisateur

Price

Price FFU series Manuel

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuel utilisateur

Brita

Brita SAFF-100 Manuel utilisateur

HEISSNER

HEISSNER FPU24000-00 Manuel utilisateur

BGS technic

BGS technic 1518 Manuel utilisateur

Reverse Osmosis

Reverse Osmosis RF Series Manuel utilisateur

ubbink

ubbink Filtramax Series Manuel utilisateur