Osaki Power Tools ENG003 Manuel utilisateur
THE ENVIRONMENT
QUALITY GUARANTEE & WARRANTY
OSAKI POWER TOOLS carry a one year manufacturer’s warranty.
OSAKI POWER TOOLS are designed & produced to the highest standards & specifications.
OSAKI POWER TOOLS are fully guaranteed against faulty materials & workmanship.
Should they be found to be defective, they will either be repaired or replaced free of charge
(fair wear and tear and/or misuse excepted). This does not affect your legal rights.
Please retain supplier invoice as proof of purchase.
OSAKI POWER TOOLS are designed for DIY and hobby use only.
They are not covered by an industrial warranty. Industrial use will invalidate this guarantee.
Specifications may change without prior notice. E&EO
DECLARATION OF CONFORMITY
We hereby certify that the
OSAKI ENG003 ELECTRIC ENGRAVER KIT
(ORDER CODE: OSA-279-9810K)
complies with all the relevant provisions of the
Machinery Directive 2006/42/EC
Standards Applied: EN 60745-1:2009+A11:2010
EMC Electromagnetic Compatibility Directive 2014/30/EU
Standards Applied: EN 55014-1:2006/+A1:2009/+A2:2011, EN 55014-2:2015, EN 61000-3-2:2014, EN 61000-3-3:2013
RoHS2 Restriction of Hazardous Substances Directive 2011/65/EU
Standards Applied: EN 50581-1:2012
Position:
Compliance Manager
Official Agent
KENNEDY TOOLS
Wigston, Leicester, England, LE18 2FS.
Always dispose of unwanted tools, accessories and packaging materials in an environmentally
friendly manner.
In observance of the European Directive on Waste Electrical and Electronic Equipment (WEEE) and
its implementation in accordance with national law, electrical goods that have reached the end
of their life must be collected separately and returned to an environmentally compatible recycling
facility.
Do not dispose of electrical goods with domestic waste materials as inappropriate disposal may
cause potential hazards to the environment and human health.
For further information, please contact your local authority or the retailer from whom you purchased
the product.
This product does not contain any restricted substances in concentrations and applications which
are banned by the European RoHS2 Directive.
© The Kennedy Group Ltd. 03/19
THE KENNEDY GROUP LTD, Wigston, Leicester, England, LE18 2FS.
ELECTRIC ENGRAVER KIT
§5-Position adjustable engraving depth
§6000rpm
§Soft grip
§Positive on/off
§1.8m Cable
§Includes 2 tips and template for letters and numbers
ENG003
ORDER CODE
OSA-279-9810K
OPERATOR’S MANUAL
Please retain this information for future reference.
WARNING:
THE SAFETY INFORMATION GIVEN INSIDE MUST BE READ
AND UNDERSTOOD BY ANY PERSON USING, INSTALLING, REPAIRING OR
MAINTAINING THIS PRODUCT.
lAlways keep your work area clean and tidy
and ensure it is always well lit. Cluttered dark
areas may cause accidents.
lAlways use the power tool and accessories in
accordance with these instructions and in
the manner the tool is intended.
lAlways stay alert to ensure your personal
safety at all times and do not use the
engraver when tired or under the influence of
medication, alcohol or drugs.
lAlways plug the engraver into an appropriate
outlet that is properly installed and grounded
in accordance with all local codes
and ordinances. Check with a qualified
electrician if you are in doubt as to whether
the outlet is properly grounded.
lAlways keep children away from work area.
lAlways ensure the engraver is OFF before
plugging in to the mains in order to avoid
any accidents
lAlways ensure the mains power supply
corresponds to the power rating on the data
label on the machine.
lAlways disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing power tools.
lAlways wear eye protection.
lNever operate tools in the presence of
flammable liquids, gases or dust; power tools
create sparks that could potentially ignite dust
or fumes.
lNever allow inexperienced people to use
the engraver without supervision.
lNever expose the engraver to rain or wet
conditions.
lNever carry the engraver by the cable and do
not use the tool at all if the cable is damaged.
lNever use the engraver with a blunt tip: cutting
tools with sharp cutting edges are easier
to control.
OPERATING INSTRUCTIONS
Osaki Power Tools are committed to the Production of Quality Power Tools that are
designed for high performance and long service life. If safety and maintenance
procedures are observed they will last for many years.
To ensure the best possible use of the Osaki Engraver tool please follow these simple operating
instructions.
1.Before you start using the engraver you must firstly install the engraver tip.
To do this you must unscrew the grub screw which is located in the engraver
point holder. Place the engraver tip inside the tip holder and firmly tighten
the grub screw (see Fig. 1). It is important to ensure that the tip is held
firmly in place by the grub screw. In order to replace a worn out tip the same
procedure should be followed. Replacement engraver tips are available from
your local supplier; please quote order code OSA-280-3100A (pack of 5 tips).
2.
This engraver is powered by an AC motor, therefore you will need
to ensure that the current you are using is the same as shown on
the label of the engraver unit.
To use the engraver, turn it “ON” by moving
the on/off switch located at the end of the engraver housing (see Fig. 2).
Then hold the engraver at a slight angle (as if holding a pencil) and ensure
your arm is comfortable by resting it on a table. It is recommended that you
start by familiarising yourself with the tool by experimenting on a few bits of scrap material and
when you are ready to start work select the setting to produce an engraving mark to meet your
requirements. Use a light touch to guide the tip and for maximum results work slower than you
would normally write.
3.To control the stroke length and depth of engraving use the adjustment dial
on the side of the engraver housing (see Fig. 3), please note this dial cannot
be used as an OFF switch. The lowest setting is pointing to number one and
the highest is number five.
4.The engraver tip is carbide steel and under most conditions it will perform very satisfactorily
on hard materials such as glass, ceramics and steel. Do not engrave electronic media such
as DVDs, CDs etc. Engraving on these materials will damage the media.
GENERAL SAFETY
Fig. 1
Fig. 2
Fig. 3
SAFETY INSTRUCTIONS
SPECIFICATIONS
Man, Earth and the Universe
are forces that create an
immovable centre of balance ... the
balance of power
“
”
CAUTION: NEVER USE THE ENGRAVER WITH A BROKEN TIP.
Model Number ENG003
Order Code OSA-279-9810K
Nominal Voltage 230v
~
50 Hz
RPM 6000
Vibration Level 1.76m/s2
Sound Power Level 65dBA
Sound pressure Level 76dBA
Power Cord Length 1.8m
Net Weight engraver 375g
Ce manuel convient aux modèles suivants
1
