Ortech OE-212BP Manuel utilisateur
WARNING
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a competent electrician.
INSTALLATION GUIDE
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY
A QUALIFIED ELECTRICIAN.
1. DO NOT let power cords touch hot surfaces
2. DO NOT install near gas or electric heaters
3. DO NOT use this LED Emergency Light other than its intended purpose
4. LED Emergency Lights can only be installed by a qualified electrician
5. This LED Emergency Light is for indoor use ONLY
Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
CAUTION
Application Notice
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE INSTRUCTIONS BELOW:
1. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes.
If acid is spilled on skin or eyes, flush acid with fresh water and contact a physician immediately
2. LED Emergency Lights should be mounted in locations and at heights where unauthorized personnel will not readily subject it to tampering
3. The use of accessory equipment not recommended by manufacturer may cause an unsafe condition, and will void the unit's warranty
4. DO NOT use this LED Emergency Light for other than its intended purpose
5. Failure to insulate unused wire may result in shock hazard or unsafe condition as well as equipment failure
Hardwire Installation
1. Extend un-switched 20 hour AC supply of rated voltage to a junction box (supplied by others) installed in
accordance with all applicable codes and standards. Leave a minimum of 8 inches of slack on the wire.
This circuit should NOT be energized / live at this time
2. Open the unit by unscrewing the cover screws on the sides of the unit. The front cover can then be removed
3. Unit is supplied with universal spider knockouts and keyhole slots stamped into the back of the cabinet.
Knock out of the appropriate hole(s) and bring wires through the hole(s) into the cabinet
4. Mount the unit securely into place. DO NOT rely on the electrical box as the only support for the unit
5. Make proper wiring connections between the AC supply and the unit's transformer:
White, Black — wire 120V-347V; Green — ground; (see Wiring Diagram below)
Wiring Diagram
AC Wiring
Working voltage: 120V-347V AC/ 50-60Hz
Black Wire (L)
White Wire (N)
Green Wire (E/G)
LED Emergency Lights
MODEL OE-212BP
INSTALLATION GUIDE
Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
LED Emergency Lights
MODEL OE-212BP
Hardwire Installation
6. Insulate unused wire. Connect ground to supplied green ground wire in accordance with local codes.
6. Reassemble all wire connections and connectors. FAILURE TO INSULATE UNUSED WIRE MAY RESULT IN A SHOCK HAZARD
6. OR UNSAFE CONDITION AS WELL AS EQUIPMENT FAILURE
7. Batteries on larger units may be shipped separately to avoid damage in shipping. Install batteries into the cabinet and
7. complete the appropriate battery connections (see Fig.2 below)
Fig.1Fig.2
8.Batteries already installed in the cabinet must be connected to the circuit board (see Wiring Diagram on page 1 and Fig.2)
9. Secure all internal wires
10.Replace cover and secure cover screws
11. Turn on AC line voltage supply
12. If the unit is supplied with a line cord, connect the line cord plug into the appropriate receptacle previously installed
13. If unit is complete with lamp heads, position the lamp heads to provide best lighting distribution by loosening head set 13.
13...screws to adjust angle and swivel. Manually rotate or turn head(s) to the desired position,
13. then tighten the set screws to lock position
IMPORTANT REMINDER — The LED Emergency Light is furnished with a sophisticated low voltage battery dropout circuit to
protect the battery from over-discharge after the useful output has been used. Allow 20 hours recharge time after installation
or power failure for full-load testing or usage
Fig.3Fig.4Fig.5
Conduit Stem
Mount Adapter
Conduit
(Non Fourni)
INSTALLATION GUIDE
Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
LED Emergency Lights
MODEL OE-212BP
Operation
1. To test, depress the TEST switch. Charge indicator will go out and the DC lamps will come on
2. Release the TEST switch. DC lamps will be extinguished, and the charge indicator will come on
3. A bright charge LED indicator light indicates a high charge rate. After the battery has reached full charge, the indicator light
will go out. Under normal operation, the high charge indicator will turn ON and OFF intermittently while the unit is in
standby mode (regular AC is present) since the charge rate will vary in order to maintain an optimal battery performance
Fig.6 Fig.7
OPERATION AND MAINTENANCE
Maintenance
1. Code requires that the equipment be tested every 30 days for 30 seconds, and that written records be maintained for all
test results and repairs. Furthermore, the equipment is to be tested once a year for the required duration as per Code.
The battery is to be replaced or the equipment repaired whenever the eqeuipment fails to operate as intended during the
duration test. The manufacturer strongly recommends compliance with all Code requirements
2. Clean lenses on a regular basis to provide maximum light distribution in case of an emergency.
NOTE — The servicing of any parts should be performed by qualified service personnel ONLY. The use of replacement
parts not furnished by the manufacturer may cause equipment failure and will void the warranty
Emergency Lamps do not come on at all:
Pilot Light is out before test...
1. Check AC supply — be sure unit has 20 hour AC supply (un-switched)
2. AC supply is OK, and indicator light is out, replace PC Board Assembly. Pilot Light is on before test
3. Either the output is shortened or overloaded, or the battery is not connected
4. Battery is severely discharged. Allow 20 hours for recharge and then retest. NOTE — This could be the result of a switched
AC supply to the unit (which has been turned OFF at some point), a battery with a shortened cell, an old battery or a
battery which has been discharged due to a long power outage and is not yet fully recharged
TROUBLESHOOTING
TROUBLESHOOTING
Instruction Manual
1-888-543-6473
1-888-541-6474
13376 Comber Way
Surrey BC V3W 5V9
www.ortechindustries.com
375 Admiral Blvd
Mississauga, ON L5T 2N1
LED Emergency Lights
MODEL OE-212BP
Emergency Lamps come on dim when test button is pressed:
Battery discharged — permit unit to charge for 20 hours and then retest. If lamps are still dim, check charger for proper
function. If charger functions correctly, replace battery.
Emergency Lamps come on when battery is first connected:
Battery may be connected in reverse polarity. Check connections. Connect Positive (+) lead to Positive (+) battery terminal
and Negative (-) lead to Negative (-) battery terminal. The lamps should then turn OFF and the charge indicator should light
when AC power is applied (see Fig.3 on page 2 of this instruction manual).
Emergency Lamps come on dim when AC power is ON:
1. Check supply voltage and AC connections. This emergency light is provided with brownout protection.
The AC supply must be at least 80% of nominal (120V on a 347V) for equipment to function normally.
2. At lower voltages, the emergency lamps will begin to glow dimly until the source voltage drops below the full turn-on point.
NOTE — This condition may also be caused by incorrectly connecting a 120V supply to the 347V transformer lead.
Nothing happens when the unit is energized:
Some model have a standard time delay built into the design of the charger board. Please allow 15 minutes with AC current
connected. At this point, the LED AC-ON and CHARGE lights should illuminate.
IMPORTANT REMINDER
**BATTERY VOLTAGE IS NEGATIVELY RELATIVE TO INPUT WATTAGE.
OE-212BP is constructed with steel housing and lightweight thermal plastic head in matching colour. It has simple and
modern design with high efficiency LED remote heads. Universal mounting pattern and keyhole slots are stamped on
the back and conduit knockouts on the sides of each unit.
≥ 90 min
Table des matières
Autres manuels Ortech Équipement d'éclairage
Ortech
Ortech OL-2HS Manuel utilisateur
Ortech
Ortech OE-DC126 Manuel utilisateur
Ortech
Ortech OE-216-150W Manuel utilisateur
Ortech
Ortech ST-PC1025 Manuel utilisateur
Ortech
Ortech VT-40W Manuel utilisateur
Ortech
Ortech 1051-S Manuel utilisateur
Ortech
Ortech OL-1H Manuel utilisateur
Ortech
Ortech WP-100W Manuel utilisateur
Ortech
Ortech Photo-eBox Plus Manuel utilisateur
Ortech
Ortech L PL50FT-3000K Manuel utilisateur
Ortech
Ortech 2400-3CCT Manuel utilisateur
Ortech
Ortech OE-212 Manuel utilisateur
Ortech
Ortech OE-316 Manuel utilisateur
Ortech
Ortech LPL-2FT-30W Manuel utilisateur
Ortech
Ortech VT-40W Manuel utilisateur
Ortech
Ortech OE-C212 Manuel utilisateur
Ortech
Ortech MH20-ST Manuel utilisateur
Ortech
Ortech DISC-RG2 Manuel utilisateur
Ortech
Ortech OD-LLG Manuel utilisateur
Ortech
Ortech OE-126 Manuel utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
