Origio Titan Manuel utilisateur

Titan Workstation

User Manual

Version 2.3 March 2019 • 2

INDEX

How To Use This Manual.......................................................................................................................................... 3

Introduction............................................................................................................................................................... 4

SAFETY INSTRUCTIONS........................................................................................................................................ 5

Before operation of the workstation.................................................................................................................... 5

INSTALLATION ........................................................................................................................................................ 6

Device Placement .............................................................................................................................................. 6

AIR FLOW WORKING PRINCIPLE.......................................................................................................................... 7

CONTROL PANEL.................................................................................................................................................... 8

GENERAL OPERATING PROCEDURES ................................................................................................................ 9

Connecting the power cord ................................................................................................................................ 9

Switching the Fans ON / OFF at Normal Speed ................................................................................................ 9

Switching the Fans ON / OFF at Reduced Speed.............................................................................................. 9

Alarm .................................................................................................................................................................. 9

Internal Light..................................................................................................................................................... 10

UV Light............................................................................................................................................................ 10

Working Heated Surface .................................................................................................................................. 10

CONTROL & PROGRAMMING.............................................................................................................................. 11

Overview of the Control Panel Menu................................................................................................................ 12

 Generalairowinformation&counter ............................................................................................................. 12

Adjusting the level intensity of the internal light................................................................................................ 13

Programming and Controlling the UV light tlmer . ............................................................................................ 13

Programming Time and Date ........................................................................................................................... 16

Display Mode Functions ................................................................................................................................... 19

HEATED SURFACE ............................................................................................................................................... 21

Operational Characteristics .............................................................................................................................. 21

Temperature Controller..................................................................................................................................... 22

User Setup ....................................................................................................................................................... 23

Accessing the parameters and information menu ............................................................................................ 23

Resetting the THI and TLO recordings............................................................................................................. 23

Channel 1 set point .......................................................................................................................................... 23

Standby ............................................................................................................................................................ 24

Keypad lock...................................................................................................................................................... 24

Operating the heated areas.............................................................................................................................. 24

Normal Operation ............................................................................................................................................. 24

Checking the temperature ................................................................................................................................ 24

TROUBLESHOOTING Your Workstation ............................................................................................................... 25

TECHNICAL SPECIFICATIONS............................................................................................................................. 29

SPARE PARTS....................................................................................................................................................... 30

OPERATING THE STEREO MICROSCOPE HEATED GLASS AND LIGHT SOURCE CONTROLLER............... 31

OPERATING THE LCD MONITOR ........................................................................................................................ 36

WARRANTY AND LIABILITY ................................................................................................................................. 37

CUSTOMER SERVICE CONTACT INFORMATION .............................................................................................. 38

Version 2.3 March 2019 • 3

HOW TO USE THIS MANUAL

Warning, Cautions and important Notes

Throughout this manual, blocks of text may be accompanied with a pictogram. These blocks are WARNINGS,

CAUTIONS, and IMPORTANT NOTES and they are used as follows:

Symbols used in this Manual:

NOTE

Used to direct attention to a special item.

WARNING

DANGER

UV light radiation hazard. Use only with shielding in

place. Protect eyes and skin from exposure to UV light.

FURTHER INFORMATION

Further information is provided in other sections or

manuals.

Version 2.3 March 2019 • 4

INTRODUCTION

You are now in possession of a high quality microprocessor-controlled TITAN workstation

and it is designed to provide:

• Protection of the processed product against particle /microbiological contamination

• Heating control of the heated work area for sample handling

 •GassingandHumidicationcontrol(Optional)

 •Heatingcontrolofthelightopeningformorphologystudyundermicroscopy(Optional)

This user manual covers the following models:

• TITAN IVF

• TITAN LAF

The TITAN workstation has a built-in microprocessor controller featuring:

• LCD display indicating fan and alarm status.

• Air velocity sensors

 •Clock(7days)andhour-counter.

• Pre-setting of automatic start-up and UV timer.

• Alarm for any deviation from safety conditions.

Furthermore, the TITAN workstation has the following characteristics:

• Negative pressure plenum for highest sample safety.

• Adjustable fan speeds.

 •Workchamberwithtabletopinstainlesssteel(AISI304).

Version 2.3 March 2019 • 5

SAFETY INSTRUCTIONS

To avoid unintended or improper operation of the workstation, please read

this manual carefully

Before operation of the workstation

Before operating your workstation, please note the following:

The work chamber is to be carefully cleaned and/or disinfected. Use only hydrogen peroxide

(H2O2Solutions)orproductssuitabletobeusedinanIVFlab.NEVERuseammoniaor

chlorinated cleaners. It is recommended to use special lint-free wipes.

To ensure that the working area is clean and sterile the workstation fan must be run at normal

speed for at least 30 minutes prior to working inside the Workstation.

Objects and instruments must be carefully cleaned and/or disinfected before bringing them into

the work chamber.

Necessary instruments for use during work must be placed within reach to avoid unnecessary

movement inside the Workstation.

Forreliableoperationitisimportantthattheair-owconditionsareasunobstructedasmuchas

possible. Therefore, never overload the work chamber.

Putonnecessarypersonalclothingforreducingparticleemissionfromoperator(i.e.gloves,

masksandgeneralcleanroomclothing).Specialattentionshouldbegiventohandsandlower

parts of the arms, as these are the parts of the operator most likely to emit particles near the

product.

All work in the workstation must be performed with slow movements. Rapid arm movements in

the chamber may cause slipstreams, which will draw contaminated air into the work chamber.

Transportofpossiblycontaminatedmaterialmaycreateairowswhichcancontaminatethe

product.

The safety cabinet must not be used for working with materials which can cause allergic

reactions, or any harm to the health of the operator or the personnel. Attention is drawn to the

riskassessmentrequirementsoftheControlofSubstancesHazardoustoHealth(COSHH)

Regulations1999.(UK)

The cabinet is not suitable for HIGH-RISK biological agents. HIGH RISK biological agents

include all etiologic agents designated Class 4 by CDC, and oncogenic viruses classed high risk

byNCI.(USA)

Never operate the workstation cabinets if the fan compartment cover is removed. If this cover is

removed, the cabinet will give no protection of the operator or the environment and the fan will

run with openly rotating blades.

The workstation will not provide any protection for operator or environment against harmful

gases or vapors.

Version 2.3 March 2019 • 6

INSTALLATION

Please see the installation manual

Device Placement

The device should be placed on a level secure surface, away from heaters, coolers and air-conditioning outlets.

The device may only be operated at temperatures ranging between 15 °C and 35°C, with a maximum

80% relative humidity, and at normal air pressure.

Do not place under a HVAC outlet

Version 2.3 March 2019 • 7

AIR FLOW WORKING PRINCIPLE

Theverticalcleanaircabinetisaturbulence-free(laminar)verticaldisplacementowofclean

air in the work chamber protecting the product against particle contamination.

Filters:TheTITANworkstationmainlterisahigh-e󰀩ciencyHEPAlterclass(H14)andthe

pre-lterofTITANisEU-3typetocapturedustparticlesforincreasedlifetimeoftheHEPA

lter.

Airvelocitymonitoring:Theturbulence-freeverticalowcanbemonitoredbymeansofanair

velocity sensor. Any deviation from safe conditions will be indicated visually and acoustically.

Version 2.3 March 2019 • 8

CONTROL PANEL

During normal use, the LED display shows the time and the day and the “Control and programming keys”

to navigate through the menu program. The numbers 0 to 9 in the control and programming keys are

for programming purposes.

Version 2.3 March 2019 • 9

GENERAL OPERATING PROCEDURES

Connecting the power cord

Connect the power cord to the mains power inlet.

The power inlet is located at the back of the workstation.

The power outlet must be grounded.

As soon as the device is connected an audible alarm will be

activated, an LED light will turn on and a message with

POWER UP ERROR will be activated on the control panel.

Pressthe“enter”buttontoswitcho󰀨thealarmandtoreturn

to safe mode.

Please see the installation manual for further information.

Switching the Fans ON / OFF at Normal Speed

Press the “1- Fan Velocity” button to turn the fans ON. When activated a small green light on top

of the button will switch on.

Press the “1- Fan Velocity Button” to turn the fans OFF. When activated the small light on top of

the button will be OFF.

Topreventanyaccidentalswitchingonoro󰀨ofthefan,thebuttonsfornormaland

reducedvelocitymustbeactivatedforatleast15secondsbeforetheytakee󰀨ect.

DO NOT WORK IN THE WORK SPACE AREA WHEN THE FANS ARE SWITCHED OFF

Switching the Fans ON / OFF at Reduced Speed

Press the “2- Fan Reduced Velocity” button to turn the fans ON. When activated a small blue

light on top of the button will switch on.

Press the “2- Fan Velocity Reduced Button” to turn the fans OFF. When activated the small light

on top of the button will be OFF.

WhenturningONthereducedspeedvelocity,theinternallightwillturno󰀨toalert

the user. The internal light can be switched on again if needed.

Alarm

When an alarm is activated an audible acoustic signal is activated. On the control panel a small

red light is activated on the Alarm button. Press the Alarm Button to mute the acoustic alarm

signal.

The error causing the alarm will be explained on the LED display.

Version 2.3 March 2019 • 10

Whentheerrorhasbeenxedtheaudiblealarmandthesmallredlightareswitchedo󰀨.

MUTING THE ACOUSTIC SIGNAL WILL NOT SOLVE THE PROBLEM THAT

CAUSED THE ERROR

Internal Light

To switch ON the illumination light of the work chamber, press the “4-Internal Light” button.

When activated, a small blue light on top of the button will switch on.

To switch OFF the illumination light of the work chamber, press the “4-Internal Light” button

again. The small light on top of the button will be OFF.

To adjust the light intensity, refer to the section “Adjusting the level intensity

of the internal light”.

UV Light

The UV light and UV light timer are optional features.

For increased safety against unintended UV radiation which will harm eyes

and skin, use the timer to start the UV decontamination when no personnel

is present in the room where the workstation is located. Use the front shield

cover (Optional) to contain the radiation

To program the UV light time, refer to the section “Programming

and Controlling the UV light timer”.

To switch OFF the illumination light of the work chamber, press the “4-Internal Light” button

again. The small light on top of the button will be OFF.

To switch ON the UV light for decontaminating the work chamber, press the “5- UV Light” button.

When activated a small yellow light on top of the button will switch on

Working Heated Surface

To operate the heated work area, refer to the section “Heated Surface”.

ToswitchONtheORIGIOLightSourceandtheworkingheatedsurface(s),pressthebutton.

When activated a small blue light on top of the button will switch on. This button simultaneously

activatestheworkingheatedsurface.(NotethisfeatureisnotavailableontheFORTUNAICSI

models)

ToswitchOFFtheworkingheatedsurface(s),pressthebuttonagain.Thesmalllightontopofthe

button will be switched OFF.

Table des matières

Autres manuels Origio Ordinateur de bureau

Origio

Origio MARS 900 CLASS II Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur