Oriental motor BLE2 Series Manuel utilisateur

Brushless Motors

QUICK START GUIDE

BLE2 Series

□Motor

□Driver

Thank you for purchasing an Oriental Motor product.

Use the product correctly after thoroughly reading the section "Safety precautions" of the operating

manual.

This document describes methods till rotating the motor after connecting it to the driver.

For details about how to use the product, refer to the supplied with the driver.

Operating manual

HM-5190

Many other useful features are also available

□QUICK START GUIDE (this document)

□Mounting screw set

Package contents

Motor (sold separately)

The gure shows an

example of the

combination type.

∗Be sure to match the motor output power with the

driver output power.

Supplied with the

combination type.

□OPERATING MANUAL



To display the rotation speed of the

gearhead output shaft.

To display the conveyor transfer speed.

To set the rotation speed externally.

To suppress the motor torque.

To hold a load by the slight

position-keeping function.

To lock the data setting.

The motor can be operated by external signals

There are two types of connection cables

which cable leading directions are dierent.

(→Refer to the right gure)

To connect the motor and driver, the dedicated

connection cable is always needed.

For the round shaft type, only the cable for leading in

opposite direction of output shaft can be used.

Connection cable (sold separately)

Leading in opposite direction

of output shaft

Leading in direction of

output shaft

Model: CC__HBLF Model: CC__HBLB

ORIENTALMOTOR CO.,LTD.

The package includes the items shown below.

Be sure to ground the Protective Earth Terminal

(ground terminal) to ensure the safe use of the product.

Refer to "1 Connecting" for details, and ground securely.

For example.....

And others.....

As mentioned in the right, various

functions are available.

Operating using

external signals

p. 33

Operating in two or

more speeds

p. 40

Refer to "Convenient functions."

OPERATING MANUAL

Motor Driver

To power supply

Programmable controller,

etc.

1 Connecting 2 Operating a motor

Connector

cap

Remove

Attach

Secure

Be sure to turn down the locking lever

till the position shown in the gure.

When the power supply is turned on, the

display shows as follows.

Display: Rotation speed

0 r/min (standstill)

Single-phase

100-120 VAC

Single-phase

200-240 VAC

Three-phase

200-240 VAC

Refer to "Connecting" Refer to "Operating"

OPERATING MANUAL OPERATING MANUAL

10 mm

(0.39 in.)

Connect a power supply cable according to the power-supply

voltage specications of the driver. Prepare the power supply

cable since it is not supplied with the product.

Be sure to ground using the

Protective Earth Terminal .

Protective Earth

Terminal

Be sure to ground the product. Failure to do so may result in electric shock or damage to the product.

Static electricity may cause damage to the product if the Protective Earth Terminals are not grounded.

Note

モーター

ケーブル

モーター

Prepare a grounding wire since

it is not supplied with the product.

AWG18 to 14 (0.75 to 2.0 mm )

AWG18 to 14

(0.75 to 2.0 mm )

Insert into CN1

Motor

To power supply

Ground terminal

Connection cable

Press

50 r/min (factory setting)

Press The motor stops.

AC power ON

Turn

Accelerate

Decelerate

Change of motor speed [ Example: 50 →1000 r/min ]

The display blinks.

You can adjust the speed while blinking.

Press

Set

Adjustment

Press

CN4

CN2

Start of motor

The display changes to lighting

from blinking, and the speed will

be set.

When you start the motor next

time, it will rotate at the set speed.

This is an example for when the cable is "leading

in direction of output shaft." In the case of the

cable of "leading in opposite direction of output

shaft," the cable leading direction is opposite in

and .

Keep the locking

lever in the position

shown in the gure, and insert.

LOCAL

RUN key

STOP key

LOCAL key

MODE key

Setting dial

LOCAL LED

Operation panel

To stop the motor

Ground

Grounding

Driver

Connection for motor and cable

Lead wire

Screwdriver

Position of lever

Locking

lever

The motor rotates.

Press

The LOCAL LED

is lit in green.

The operation using the operation

panel was set, and the rotation speed

and rotation direction are alternately

continued to show on the display.

Interval of approximately 1 second

Press the LOCAL key.

Operation selection

2Rotation direction selection

∗ The gures show the round shaft type.

With the combination type, the gearhead output

shaft rotates in the opposite direction to the above

gure when the gear ratio is 30, 50, and 100.

(When the gear ratio is 30 and 50 for the 200 W type)

The motor rotation

direction changes whenever

the MODE key is pressed.

Press

L

N

L 1

L 2

L 1

L 2

L 3

Autres manuels Oriental motor Moteur

Oriental motor

Oriental motor AR Series Manuel utilisateur

Oriental motor

Oriental motor NX Series Manuel utilisateur

Oriental motor

Oriental motor NX Series Manuel utilisateur

Oriental motor

Oriental motor aStep ARM24 Manuel utilisateur

Oriental motor

Oriental motor CRK Series Manuel utilisateur

Oriental motor

Oriental motor PKP Series Manuel utilisateur

Oriental motor

Oriental motor World K Series Manuel utilisateur

Oriental motor

Oriental motor BMU Series Manuel utilisateur

Oriental motor

Oriental motor Alpha Step AZ Series Manuel utilisateur

Oriental motor

Oriental motor BLH Series Manuel utilisateur

Oriental motor

Oriental motor AR Series Manuel utilisateur

Oriental motor

Oriental motor BLE Series Manuel utilisateur

Oriental motor

Oriental motor BLV Series Manuel utilisateur

Oriental motor

Oriental motor NX Series Manuel utilisateur

Oriental motor

Oriental motor BMU Series Manuel utilisateur

Oriental motor

Oriental motor SMK Series Manuel utilisateur

Oriental motor

Oriental motor PK Series Manuel utilisateur

Oriental motor

Oriental motor AZ Series Manuel utilisateur

Oriental motor

Oriental motor CSK Series Manuel utilisateur

Oriental motor

Oriental motor K II S Series Manuel utilisateur

Oriental motor

Oriental motor BMU Series Manuel utilisateur

Oriental motor

Oriental motor CVK Series Manuel utilisateur

Oriental motor

Oriental motor MCS14 Manuel utilisateur

Oriental motor

Oriental motor PK Series Manuel utilisateur

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur