Oricom CARE80 Manuel utilisateur
User Guide
CARE80
Amplified Phone with direct dial picture buttons
Keep this user guide for future reference. Always retain your proof of purchase
in case of warranty service and register your product on line at: AUSTRALIA:
www.oricom.com.au
1
Table of contents
General Information ...............................................................2
Installation.............................................................................4
Location of Controls...............................................................6
Operation...............................................................................7
Memory...............................................................................10
Consumer Support............................................................... 11
Warranty Informationrt.........................................................12
Need Help?
If you need assistance setting up or using your Oricom product now or in
the future, call Oricom Support.
Australia 1300 889 785
www.oricom.com.au
Mon-Fri 8am – 6pm AEST
New Zealand 0800 67 42 66
www.oricom.co.nz
Mon-Fri 10am – 8pm NZST
2
General Information
General Information
WARNING
It is very important that you read the User Guide
carefully as it contains detailed information on
installation, programming and operational issues which
you will need to be aware of to ensure the Care Phone
operates properly. Following is a list of some of the
important issues and important warnings which you
need to be aware of.
This is a summary of the important issues you must
still read the User Guide in full.
• Thetelephoneisdesignedforindooruseonly.Donot
install the telephone in areas where there is the risk
of an explosion, excessive exposure to smoke, dust,
vibrations, chemicals, moisture and heat.
• Donotuseyourtelephoneduringanelectrical
thunderstorm as it is possible to get an electric
shock. Refer to information contained in Telstra White
pages directory.
• Theearpieceofthehandsetmayattractsmallmetal
objects such as staples and pins. Care should be
taken when placing the handset near these items.
• Settingthereceivervolumetomaximummay,under
some situations cause ear damage. We suggest
returning the handset volume control to the “0”
position after each call.
• Donotinstallindamplocationssuchasabathroom
or laundry, do not expose the unit to direct sunlight.
3
General Information
Notes for operation in New Zealand
The grant of a Telepermit for any item of terminal equipment indicates
only that Telecom has accepted that the item complies with the minimum
conditions for connection to its network. It indicates no endorsement
of the product by Telecom, nor does it provide any sort of warranty.
Above all, it provides no assurance that any item will work correctly in
all respects with another item of Telepermitted equipment of a different
make or model, nor does it imply that any product is compatible with all
of Telecom’s network services.
This equipment shall not be set to make automatic calls to the Telecom
“111” Emergency Service.
This equipment may not provide for the effective hand-over of a call to
another device connected to the same line.
This equipment should not be used under any circumstances that may
constitute a nuisance to other Telecom Customers.
REN (RN for New Zealand)
The REN (Ringer Equivalence Number) or (RN) is of signicance only if you
wish to connect more than 1 telephone to your telephone line. A standard
telephone line has a maximum REN capacity of 3 (RN of 5). It is possible
to connect 3 devices with a REN of 1 (RN of 1) with no degradation to the
product’s performance. Exceeding this limit may cause the volume of the
ringer in any phone to decrease or not ring at all.
4
Installation
Installation
Connecting the telephone
1. Plug one end of the telephone cable supplied into the TEL. LINE jack
at the back of the telephone base.
2. Plug the other end of the telephone cable into the wall outlet.
3. Plug one end of the curly cord into the socket on the handset.
4. Plug the other end of the curly cord into the left side of the telephone.
Wall Mounting
Method A. To t to an existing telephone wall plate with modular
connector simply,
1. Press and lift out the handset holder
on base. Rotate it 180°, and snap it
into place (see Fig A) so it will hold the
handset in place when the phone is
mounted on the wall.
2. Insert the mounting bracket’s two tabs
into the matching slots on the phone’s
base. (see Fig B)
3. Then press down and slide the bracket
Upward until the tabs snap into place.
4. Plug the short telephone line cord
(supplied) into the base of the phone and
plug the other end into the telephone
wall plate socket.
5. Position the mounting holes on the base of the phone over the two
protruding screws on the wall plate. Gently push the phone flush
against the wall plate then slide the phone downwards locking it into
place.
4 4
4
4
4
Fig A
1
2
33
Fig B
5
Installation
Method B. Attach directly to a wall
1.Drilltwoholesvertically,oneabovetheother,83mmapart,andleave
the screws protruding from the wall by 5mm.
2. Follow steps 1 and 2 above.
3. Then press down and slide the bracket upward until the tabs snap into
place.
4. Plug one end of the telephone cable into the TEL. LINE jack at the
back of the base.
5. Plug the other end of the telephone cable into the telephone socket,
then align the base’s keyhole slots with the screws and slide the phone
downward to secure it.
6
Location of Controls
Location of Controls
1. Hook switch
2. Handset holder
3. Coil cord socket
4. Receiver volume controller
5. Store button
6. Telephone line socket
7. One touch button(M1-M6)
8. Ring Hi/Mid/Off switch
9. Recall Time Switch
10. Memory button
11. Recall button
12. Tone Hi/Low switch
13. Redial button
14. Amplify key
15.RingLEDindicator
16. Keypad
17.AmplifyLEDindicator
1
2
3
4
8
12
10
11
13
14
6
15 16
7
9
17
5
7
Operation
Operation
Recall switch Setting
For Australia the Recall switch should be set to 100.
For New Zealand the Recall switch should be set to 600.
Making a call
1. Pick up the handset and wait for a dial tone.
2.Dialthenumberyouwishtocall.
3. When you have completed your call, hang up the handset.
Receiving a Call
Whenyoureceiveacall,thetelephonerings,theRingerLEDashes.
If you want to talk to the caller:
1. Pick up the handset to answer the call.
2. At the end of the call, return the handset to the cradle.
Redial function
If a number that you have dialed is engaged or you were unable to get
through to anybody. The last number dialed will be saved in the telephone
automatically.
To use the redial facility, proceed as follows:
1. Lift the handset.
2. Press the REDIAL button. The last saved redial number will now be
dialled.
Pause
If needed for phone banking or behind a PBX system. You can insert a
3.6 seconds pause while dialing or storing a number into MEM. Press
REDIAL button at the desired point in number to insert a pause.
8
Operation
Recall and call waiting
Press the Recall button followed by the extension number to transfer
calls when connected to a PBX.
Access to additional network services can be gained by using the Recall
button * and # keys. Contact your network operator for more information.
To Turn on Telstra call waiting (Australia)
You can use the recall button to answer a second call while you are on
the phone. However this service will need to be turned on. For example to
turn on Telstra’s Call Waiting service:
1. Lift the handset and wait for dial tone then Press *43#.
2. You will hear the service message and then hang up.
Take two different calls at the same time
Duringacall,youwillheartwoloudbeepsperiodicallytonotifyyouof
another incoming call. If you wish to answer this call
1. Press Recall button listen for dial tone then Press 2 to put the
current call on hold and talk with the second caller.
2. Subsequent presses of Recall button listen for dial tone then Press
2will toggle you between these 2 callers.
Ringer Volume Control
The ringer sound level can be adjusted by sliding the RINGER switch to
select high (HI) or soft (MID) sound level. When you don’t
want to be disturbed, slide the RINGER switch to the Off position.
ThebrightRedlight(LED)onthebasewillashwithallincomingcalls.
Autres manuels pour CARE80
1
Table des matières
Autres manuels Oricom Téléphone
Oricom
Oricom TP6 Manuel utilisateur
Oricom
Oricom TP9 Manuel utilisateur
Oricom
Oricom HP100 Manuel utilisateur
Oricom
Oricom ECO7100-1 Manuel utilisateur
Oricom
Oricom Pro900 Manuel utilisateur
Oricom
Oricom CARE920-1 Manuel utilisateur
Oricom
Oricom TP58 Manuel utilisateur
Oricom
Oricom TP150 Manuel utilisateur
Oricom
Oricom BT9500 Manuel utilisateur
Oricom
Oricom CARE95 Manuel utilisateur
Oricom
Oricom TCR10 Manuel utilisateur
Oricom
Oricom CARE80 Manuel utilisateur
Oricom
Oricom TP68 Manuel utilisateur
Oricom
Oricom care60 Manuel utilisateur
Oricom
Oricom Professional Series PRO90 Manuel utilisateur
Oricom
Oricom CARE80S Manuel utilisateur
Oricom
Oricom TP9 Manuel utilisateur
Oricom
Oricom TP30 Manuel utilisateur
Oricom
Oricom TP170WP Manuel utilisateur
Oricom
Oricom Care10 Manuel utilisateur
