Orbit OceanTRx7 Fiche technique
COMMUNICATION WITHOUT BOUNDARIES
Orbit Communication Systems Ltd. P.O.B. 42504, Israel, Tel: +(972) 9 892 2777, Fax: +(972) 9 885 5944 www.orbit-cs.com
OceanTRx7TM
Maritime Stabilized VSAT System
Technical Note
OceanTrx CCU Installation and replacement
Document: TEC32-1664-014
Jan 2016
TEC32-1664-014_A OceanTRx™ CCU Technical Note ii
Copyright
© 2013 Orbit Communication Systems Ltd. All rights reserved.
All product names are trademarks of Orbit Communication Systems Ltd.
Other names are the property of the respective owners.
No part of this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any form or
by any means, electronic or otherwise, without the prior written permission of Orbit
Communication Systems Ltd.
Disclaimer of Warranty
Orbit Communication Systems Ltd. has made every effort to ensure the accuracy and
relevancy of the material in this document. It is expected that all sections of this
document will be read thoroughly and that all information and procedures should be
fully understood.
However, Orbit Communication Systems Ltd. assumes no responsibility for any errors
that may appear in this document, and reserves the right to make changes to the
document without notice.
Orbit Communication Systems Ltd. makes no warranty of any kind in regard to this
document, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose.
Orbit Communication Systems Ltd. disclaims any responsibility for incidental or
consequential damages in connection with the furnishing, performance or use of this
document.
Parts of this document may be based on hardware or software developed by
third-party vendors. Orbit Communication Systems Ltd. disclaims any responsibility for
the accuracy of this document with respect to such hardware and software, and
assumes no responsibility for incidental or consequential damages arising due to
discrepancies between this document and such hardware or software.
TEC32-1664-014_A OceanTRx™ CCU Technical Note iii
Revision History and Control
Revision History
Rev #
Modified by
Date
Comments
.
Albert
September 24, 2013
New Release
A
Albert/Tal.I
January 07 ,2016
Update according Changing CCU Software
and Part numbers
TEC32-1664-014_A OceanTRx™ CCU Technical Note iv
About this Manual
This manual is designed to guide you through the procedures required for maintaining the
CENTRAL CONTROL UNIT (CCU) for the OceanTRx7™ Maritime Satellite Communication
System.
Text Conventions
Style
Indicates
Example
Text
Normal descriptive text
Contents
Text
Words or figures that appear on the
screen or that should be typed
The name of a file or directory
System Status
<Text>
A key to be pressed
<ESC>
TEXT
The name of a hardware
component
ANTENNA
Text
The name of a GUI element
Operation Screen
The description of a procedure
To configure…
Notations
Indicates important information that should be noted.
Indicates a potential hazard.
Indicates the safest method of installation or an operation that must be adhered
to.
TEC32-1664-014_A OceanTRx™ CCU Technical Note v
Effective Releases
This document is effective for both OrBand™ and OceanTRx™ Maritime Satellite
Communication Systems.
For a description of the changes between OrBand™ and OceanTRx7™, refer to the
OceanTRx7™Maritime Satellite Communication System Release Notes
.
TEC32-1664-014_A OceanTRx™ CCU Technical Note vi
Table of Contents
1Introduction .....................................................................................................................1
1.1 Purpose....................................................................................................................1
1.2 CCU Description .....................................................................................................2
1.2.1 CCU Description .................................................................................................2
1.3 Spare Kit Contents ...................................................................................................4
1.4 Required Tools and Parts.........................................................................................4
2Preliminary Procedures ...................................................................................................5
3Replacing the CCU..........................................................................................................6
3.1 Removing the CCU ..................................................................................................6
3.2 Installing a CCU .......................................................................................................7
4SETUP............................................................................................................................8
4.1 Select CCU mode (working set) ...............................................................................8
4.2 Configuring the CCU IP and host communication IP address...................................9
4.3 Configuring the compass input. ..............................................................................10
4.4 Updating the system with General Software update module (GSU)........................11
5Perform Verification Test...............................................................................................13
6Appendices ...................................................................................................................14
6.1 Appendix A: Routing and Wiring.............................................................................14
TEC32-1664-014 OceanTRx7™ CCU Technical Note Page 1 of 15
1Introduction
1.1 Purpose
The purpose of this Technical Note is to provide detailed instructions on how to replace and
configure the CENTRAL CONTROL UNIT (CCU).
Figure 1-1: Central Control Unit
TEC32-1664-014 OceanTRx7™ CCU Technical Note Page 2 of 15
1.2 CCU Description
1.2.1 CCU Description
The CENTRAL CONTROL UNIT (CCU) is the interface between the system, the ship’s
equipment and the human operator.
The CCU provides the following functions:
Modem interface.
Conversion of compass readings.
Integrated Receiver/Decoder (IRD) interface.
Tx and Rx signal attenuation.
De-muxing and muxing of Tx and Rx signals, LAN and 10MHz reference signal.
Ethernet Hub
Running platform for MtsVLink software.
Transmission of system GPS data to the CFE modem.
SNMP support for network management.
The CCU is 1U high and is typically installed on a dedicated 19-inch rack in the ship’s radio
room.
There are two versions of the CCU supported by the system:
CCU –requires 10 MHz reference to be supplied by CFE modem And
Nmea-0183 Compass Only .
CCU WITH 10 MHZ –includes an internal 10 MHz reference source And
Synchro step by step ,Nmea-0183
The CCU requires external VGA display and keyboard with touchpad.
Orbit offers foldable 1U 17’ LCD drawer P/N: KIT32-1664-082-SP
TEC32-1664-014 OceanTRx7™ CCU Technical Note Page 3 of 15
The rear panel includes several connectors that connect to the ADE, the modem and the
ship’s gyrocompass (NMEA-0183, Synchro or Step-by-Step). An ATTENUATOR SWITCH
allows adaptation to various ADE-BDE cable lengths.
The CCU contains the BDMX module that connects to the ADMX via a single coaxial cable. The
BDMX provides integral amplification/attenuation of the Tx and Rx paths.
System operation is fully controlled from the CCU. Using the HMI, the operator can select the
desired satellite and channel from the CCU’s Satellite database. The system automatically
extracts the required data and deploys the ACU to acquire and track the selected satellite,
while compensating for the platform’s pitch, roll and yaw movements.
Figure 1-2: Front Panel Central Control Unit
Figure 1-3:Rear Panel Central Control Unit
TEC32-1664-014 OceanTRx7™ CCU Technical Note Page 4 of 15
1.3 Spare Kit Contents
The following table provides a list of the parts in the CCU spare kit.
Table 1-1: Spare Part Kit Contents (CCU regular)
KIT32-1664-031-SP
P/N
Description
Quantity
L00720008
CENTRAL CONTROL UNIT 1U W/O 10MHz&SYNCHRO
1
USB33-0823
MARINE USB LOAD WITH I/O MAN&DCD
1
Table 1-2: Spare Part Kit Contents (CCU with 10MHz source)
KIT32-1664-032-SP
P/N
Description
Quantity
L00720009
CENTRAL CONTROL.U W/10MHz&SYN
1
USB33-0823
MARINE USB LOAD WITH I/O MAN&DCD
1
1.4 Required Tools and Parts
The following table provides a list of tools and customer-supplied parts that are needed to
perform the procedures in this Technical Note.
Table 1-3: Required Tools and Parts
Tool/Part Name
Figure
Medium Phillips screwdriver
Small Flat screwdriver
Open wrench 13mm
Autres manuels pour OceanTRx7
3
Table des matières
Autres manuels Orbit Équipement marin
Manuels Équipement marin populaires d'autres marques
Clarion
Clarion GR10BT Manuel de réparation
Raymarine
Raymarine Maxiview ST80 Guide de l'utilisateur
GUIDANCE MARINE
GUIDANCE MARINE 20- Series Instructions de montage
Raymarine
Raymarine ST60 Tridata Guide de l'utilisateur
olympia electronics
olympia electronics ΒS-531/1/MAR Manuel utilisateur
Sonic
Sonic 2024 Manuel utilisateur